2007 MITSUBISHI LANCER EVOLUTION Service Repair Manual

STEERING - Power Steering Oil Hoses37A-31

Pre-removal and Post-installation Operation
Power Steering Fluid Draining and Refilling (Refer to
P.37A-9.)
12±2 N·m
17
16
15
12
18±3 N·m
Crossmember
1
57±7 N·m
9
8 47
32 5
12±2 N·m15±3 N·m
18±2 N·m 12±2 N·m
49±10 N·m
52±7 N·m*
12±2 N·m
6
10
11
167±10 N·m
14 13
18
12±2 N·m
12±2 N·m
Removal steps
1. Oil reservoir
"BA2. Suction hose
3. Return hose
4. Return hose
5. Return tube
DStrut tower bar (Refer to GROUP 42.)
6. Return hose
DClock spring (Refer to GROUP 52B.)
DCrossmember bar
(Refer to GROUP 33A.)
DCenter member (Refer to GROUP 32.)
DFront exhaust pipe
(Refer to GROUP 15.)
7. Steering gear and joint connecting
bolt8. Rear roll stopper connecting bolt
9. Rear roll stopper
(Refer to GROUP 32.)
AA"10. Eye bolt
11. Gasket
"BA12. Pressure hose assembly
"AA13. O ring
14. Return hose
15. Return tube
AA"16. Return tube
17. O ring
DFront bumper (Refer to GROUP 51.)
DIntercooler (Refer to GROUP 15.)
18. Cooler tube assembly

STEERING - Power Steering Oil Hoses37A-32

Pre-removal and Post-installation Operation
Power Steering Fluid Draining and Refilling (Refer to
P.37A-9.)
12±2 N·m
15
12
18±3 N·m
Crossmember
1
57±7 N·m
9
8 4
7
32 5
12±2 N·m
15±3 N·m
18±2 N·m 12±2 N·m
49±10 N·m
52±7 N·m*
12±2 N·m
6
10
11
167±10 N·m
14
13
12±2 N·m
Removal steps
1. Oil reservoir
"BA2. Suction hose
3. Return hose
4. Return hose
5. Return tube
DStrut tower bar (Refer to GROUP 42.)
6. Return hose
DClock spring (Refer to GROUP 52B.)
DCrossmember bar
(Refer to GROUP 33A.)
DCenter member (Refer to GROUP 32.)
DFront exhaust pipe
(Refer to GROUP 15.)7. Steering gear and joint connecting
bolt
8. Rear roll stopper connecting bolt
AA"9. Eye bolt
10. Gasket
"BA11. Pressure hose assembly
"AA12. O ring
AA"13. Return tube
14. O ring
DFront bumper (Refer to GROUP 51.)
DIntercooler (Refer to GROUP 15.)
15. Cooler tube assembly

STEERING - Power Steering Oil Hoses37A-33
REMOVAL SERVICE POINT
AA"EYE BOLT/RETURN TUBE REMOVAL
1. Loosen the crossmember mounting bolts and nuts, and
lower the crossmember to a position so that the eye bolts
or return tube at the steering gear side can be removed.
NOTE
In this case, do not remove the crossmember
mounting bolts and nuts.
2. Remove the eye bolts or return tube.
INSTALLATION SERVICE POINTS
"AAO RING INSTALLATION
No.ID×Width mm
111.0×1.9
213.0×1.9
"BAPRESSURE HOSE ASSEMBLY/SUCTION HOSE
INSTALLATION
Install the pressure hose assembly and suction hose as
illustrated.
1
2
Suction hose
Pressure hose
assembly
Marking
Notch

NOTES

42-1
BODY
CONTENTS
HOOD2 .................................
ON-VEHICLE SERVICE 2..................
Adjustment of Clearance around Hood 2......
Adjustment of Alignment of Hood Stepped
Portion and Hood Striker 2..................
Adjustment of Hood Height 2.................
HOOD 3..................................
FENDER4 ..............................
SPECIAL TOOL 4.........................
FENDER 5................................
FUEL FILLER DOOR7 .................
STRUT TOWER BAR AND REAR END
CROSS BAR8 ...........................
WINDOW GLASS9 .....................
ADHESIVE 9..............................
SPECIAL TOOLS 9........................
WINDOW REPAIR 9.......................
WINDSHIELD 11...........................
REAR WINDOW GLASS 16................
DOORS19 ..............................
SERVICE SPECIFICATIONS 19.............ADHESIVES 19............................
SPECIAL TOOLS 19.......................
TROUBLESHOOTING 20...................
ON-VEHICLE SERVICE 20.................
Door Adjustment 20.........................
Door Window Glass Adjustment 21...........
Adjustment and Replacement during Power
Window Malfunction 22......................
Power Window Safety Mechanism Check 22..
Power Window Timer Function Check 22......
Door Outside Handle Looseness Check 23....
Power Window Operation Current Check 23...
Circuit Breaker Check 23....................
Power Window Check 23....................
Door Inside Handle Looseness Check and
Adjustment 24...............................
DOOR ASSEMBLY 25......................
DOOR TRIM AND
WATERPROOF FILM 27....................
DOOR GLASS AND REGULATOR 32.......
DOOR HANDLE AND LATCH 35...........
WINDOW GLASS RUNCHANNEL AND
DOOR OPENING WEATHERSTRIP 38.......
TRUNK LID41 ..........................

BODY -Hood42-2
HOOD
ON - VEHICLE SERVICE
ADJUSTMENT OF CLEARANCE AROUND
HOOD
ADJUSTMENT OF ALIGNMENT OF HOOD
STEPPED PORTION AND HOOD STRIKER
ADJUSTMENT OF HOOD HEIGHT
With the marker as guide, turn the hood bumper to adjust
the hood height. The hood bumper height changes approx.
3mm (new hood bumper with one complete turn).
A
A
Section A-A
16.3 mmHood
Hood bumper

BODY -Hood42-3
HOOD
REMOVAL AND INSTALLATION
13
23
4 5
9 7
18
62
9.0±2.0 N·m
10
12 13
15
16 17
7
A A
Section A - ASection B - B
B B
1111
10
15
Remarks
and indicate the clip position.
Clip
11
151010
15
18
14
Clip
1. Hood bumper
Hood lock release cable removal
steps
DFront bumberassembly
(Refer to GROUP51.)
DSplash shield (Refer to P.42-5.)
2. Hood latch
3. Hood lock release handle
4. Hood lock release cable
Hood removal steps
5. Hood weather strip
6. Hood weather strip7. Head lamp weather strip
8. Hood support rod
9. Hood inlet garnish lower
10. Heat protector panel
11. Hood insulator
DWasher hose and nozzle connection
(Refer to GROUP51.)
12. Hood inlet garnish upper
13. Hood outlet garnish
"AA14. Hood hinge bolt (hood side)
15. Hood
16. Hood hinge
17. Shim
18. Hood weather strip

BODY -Hood/Fender42-4
REMOVAL SERVICE POINTS
"AAHOOD HINGE BOLT INSTALLATION
Caution
Use the special parts as the aluminum hood uses special
coatings on the of the hood hinge bolt.
FENDER
SPECIAL TOOLS
ToolNumberNameUse
MB990784Ornament removerSide turn signal lamp removal