2007 MITSUBISHI LANCER EVOLUTION drain bolt

BODY DIMENSIONS -Type A (Projected Dimensions)
124
9105,6,7,8
7
5
6
8
B-5
mm
690
1,335
1,545
1,230
185339162180330
563
100
345
340497
250502
338
253
203
11 4204142
1
2
3456
7
89
1011
No.Standard measurement pointHoleSize
shape mmNo.Standard measurement pointHoleSize
shape mm
1*Centre of under cover mounting holeÓ-87Front edge of center bearing mounting bolt-
2Notch of front sidemember inner-8Front edge of center bearing mounting bolt-
3*Centre of crossmember mounting holeÓ-189*Centre of rear seat crossmember positioning holeÓ-22·38
4*Centre of front fioor sidemember positioning holeÓ-2510*Centre of crossmember mounting holeÓ-14
5Front edge of center bearing mounting bolt-11*Centre of rear floor sidemember extension drain
holeÓ-20
6Front edge of center bearing mounting bolt-
NOTE: The ”*” in the No. column means the frame centre ring gauge mounting position.

BODY DIMENSIONS -Type B (Actual-measurement Dimensions)
123
495,6,7,8
7
5
6
8
1011
B-9
No.Standard measurement pointHoleSize
shape mmNo.Standard measurement pointHoleSize
shape mm
1Centre of under cover mounting holeÓ-87Front edge of center bearing mounting bolt-
2Notch of front sidemember inner-8Front edge of center bearing mounting bolt-
3Centre of crossmember mounting holeÓ-189Centre of rear seat crossmember positioning holeÓ-22·38
4Centre of front fioor sidemember positioning holeÓ-2510Centre of crossmember mounting holeÓ-14
5Front edge of center bearing mounting bolt-11Centre of rear floor sidemember extension drain
holeÓ-20
6Front edge of center bearing mounting bolt-

ENGINE -Oil Pan11A-24
1 2 34
5
39±5 N·m 42±2 N·m
9.0±3.0 N·m 22±4 N·m
6
7
8 9
10
11
9.0±3.0 N·m
26±5 N·m14±1 N·m 9.0±1.0 N·m

9.0±1.0 N·m

10±2 N·m
Removal steps
1. Bell housing cover
2. Oil return pipe gasket
3. Oil return pipe
4. Oil return pipe gasket
"CA5. Oil return pipe gasket
6. Engine oil cooler return hose7. Engine oil cooler tube gasket
8. Drain plug
"BA9. Drain plug gasket
AA""AA10. Oil pan
11. Baffle plate
REMOVAL SERVICE POINT
AA"OIL PAN REMOVAL
MD998727MD998727

ENGINE -Oil Pan11A-25
INSTALLATION SERVICE POINTS
"AAOIL PAN INSTALLATION
1. Remove sealant remained on the oil pan and the cylinder
block.
2. Apply sealant on the mounting surface of oil pan without
any gap as indicated in the figure, and install oil pan
on cylinder block.
Specified sealant:
MITSUBISHI GENUINE PART MD970389 or
equivalent
3. Tighten the mounting bolt of oil pan to the specified torque.
Be careful not to use a wrong bolt when tightening the
bolt as shown in the illustration.
Tightening Torque: 9.0±3.0 N·m
"BADRAIN PLUG GASKET INSTALLATION
Gasket should be replaced with a new one, and install it
in the direction specified in the figure.
"CAOIL RETURN PIPE GASKET INSTALLATION
Gasket should be replaced with a new one, and set the convex
part to the position as shown in the illustration for installation.
NOTE
There is no specific direction indicated for installing the
turbocharger side of the oil return pipe gasket.
INSPECTION
DCheck oil pan for cracks.
DCheck oil pan sealant - coated surface for damage and
deformation.
DCheck oil screen for cracked, clogged or damaged wire
net and pipe.
ø4 mm
at the groove
at the bolt hole
M6×8mm
Gasket
Oil Pan Side
Convex part

ENGINE OVERHAUL -Specifications11B-7
Items Tightening torque N·m
Water outlet fitting bolt10±1
Thermostat housing bolt23±4
Water inlet pipe bolt (M6)10±1
Water inlet pipe bolt (M8)13±2
Water pump bolt14±1
Knock sensor23±2
Rocker arm, camshaft
Cam position sensor bolt8.8±1.0
Cover bolt10±2
Cam position sensing cylinder bolt22±4
Cam position sensor support bolt14±1
Bearing cap bolt20±1
Oil delivery body bolt11±1
Cylinder head, valve
Cylinder head bolt78±2→Completely loosen→20±2→90_+90_
Oil pump, oil pan
Drain plug39±5
Oil pan bolt9±3
Oil screen bolt19±3
Baffle plate bolt22±4
Oil pressure switch19±3
Oil cooler bypass valve54±5
Relief plug44±5
Oil filter bracket bolt19±3
Plug cap23±3
Flange bolt36±3
Oil pump case bolt23±3
Oil pump cover bolt17±1
Oil pump cover screw10±2
Piston, connecting rod
Connecting rod cap nut20±2+90_-94_
Crankshaft, cylinder block
Flywheel bolt132±5
Rear plate bolt11±1
Bell housing cover bolt9±1
Rear oil seal case bolt11±1
Beam bearing cap bolt25±2+90_- 100_
Check valve32±2
Throttle body
Throttle position sensor bolt2.0±0.5
Turbocharger
Waste gate actuator bolt11.3±1.5

ENGINE OVERHAUL -Oil Pump and Oil Pan11B-47
OIL PUMP AND OIL PAN
REMOVAL AND INSTALLATION
2
1
Apply engine oil on
all sliding sections
before installing.
4 56
12 13
16187 20
38
9
10 1415
1719
1139±5N•m 54±5N•m19±3N•m
36±3N•m23±3N•m 17±1N•m 10±2N•m
9±3N•m 22±4N•m 23±3N•m
19±3N•m
44±5N•m 23±3N•m
25
24232221
26272930
31
28
19±3N•m
Removal steps
1. Drain plug
"NA2. Drain plug gasket
"MA3. Oil filter
AA""LA4. Oil pan
5. Oil screen
6. Oil screen gasket
7. Baffle plate
"KA8. Oil pressure switch
9. Oil cooler bypass valve
10. Relief plug
11. Gasket
12. Relief spring
13. Relief plunger
14. Oil filter bracket
15. Oil filter bracket gasket
AB""JA16. Plug cap
17. O-ringAC""IA18. Flange bolt
"HA19. Oil pump case
20. Oil pump case gasket
21. Oil pump cover
"GA22. Oil pump driven gear
"GA23. Oil pump drive gear
"FA24. Crankshaft front oil seal
"EA25. Counter balance shaft oil seal
"DA26. Oil pump oil seal
27. Counter balance shaft, right
28. Counter balance shaft, left
AD""CA29. Counter balance shaft front bearing
AE""BA30. Counter balance shaft rear bearing,
right
AE""AA31. Counter balance shaft rear bearing,
left

ENGINE COOLING -Water Pump14-13
WATER PUMP
Caution
If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched.
REMOVAL AND INSTALLATION
Pre-remobal and Post-installation Operation
DEngine Coolant Draining and Supplying (Refer to P.14-6.)
DTiming Belt Removal and installation (Refer to GROUP 11A.)
1
Bolt specifications
28×22
2
23±3 N·m
14±1 N·m
Nominal diameter×Nominal length mm
8×70
8×14
8×22 8×25
3 4
22±4 N·m
Removal steps
1. Alternator brace
2. Water pump
3. Water pump Gasket
"AA4. O-ring
INSTALLATION SERVICE POINT
"AAO-RING INSTALLATION
Fit an O-ring into the O-ring groove located at the end of
the water inlet pipe and apply water to the O-ring or the
inside of the mounting surface of the water pump for insertion.
CAUTION
Do not let the O-ring get contaminated with grease, such
as engine oil.Water pump
O-ring
Water inlet pipe

ENGINE COOLING -Water Hose and Water Pipe/Radiator14-15
REMOVAL SERVICE POINT
AA"RADIATOR UPPER HOSE/RADIATOR LOWER
HOSE DISCONNECTION
After making mating marks on the hose and the hose clamp,
disconnect the hose.
INSTALLATION SERVICE POINTS
"AAO-RING INSTALLATION
Fit an O-ring into the groove of the water inlet pipe and
apply water to the circumference of the O-ring or the
inside of the mounting surface of the pipe for insertion.
CAUTION
Do not let the O-ring get contaminated with grease, such
as engine oil.
"BAWATER INLET PIPE INSTALLATION
After installing the water outlet fitting and the thermostat
case assembly, tighten the mounting bolt of the water
inlet pipe to the specified torque.
"CARADIATOR LOWER HOSE/RADIATOR UPPER
HOSE CONNECTION
1. Insert each hose as far as the projection of the water
inlet pipe or water outlet fitting.
2. Align the mating marks on the radiator hose and hose
clamp, and then connect the radiator hose.
INSPECTION
WATER PIPE AND HOSE CHECK
Check the water pipe and hose for cracks, damage, clog
and replace them if necessary.
RADIATOR
REMOVAL AND INSTALLATION
Pre-remobal and Post-installation Operation
DEngine Coolant Draining and Supplying (Refer to P.14-6.)
DUnder Cover Removal and Installation (Refer to GROUP 51 - Front Bumper.)
DAir Cleaner Assembly Removal and Installation (Refer to GROUP 15.)
DAir Hose E, Air Pipe C, Air hose D Removal and Installation (Refer to GROUP 15 - Intercooler.)
DBattery and Battery Tray Removal and Installation
Water pump or
thermostat case
O-ring
Warter inlet pipe