Page 1137 of 2896
DI-28
WARNING LAMPS
Revision: June 20062007 Versa
LKWA0354E
Page 1138 of 2896
WARNING LAMPS
DI-29
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
LKWA0355E
Page 1139 of 2896
DI-30
WARNING LAMPS
Revision: June 20062007 Versa
LKWA0356E
Page 1140 of 2896
WARNING LAMPS
DI-31
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
LKWA0357E
Page 1141 of 2896
DI-32
WARNING LAMPS
Revision: June 20062007 Versa
LKWA0358E
Page 1142 of 2896
WARNING LAMPS
DI-33
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
LKWA0359E
Page 1143 of 2896

DI-34
WARNING LAMPS
Revision: June 20062007 Versa
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)EKS00I0T
1. CHECK OIL PRESSURE WARNING LAMP OPERATION
Activate IPDM E/R auto active test. Refer to PG-21, "
Auto Active Test" .
Does oil pressure warning lamp blink?
YES >> GO TO 2.
NO >> GO TO 5.
2. CHECK IPDM E/R INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R harness connector and
ground.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
NG >> GO TO 3.
3. CHECK OIL PRESSURE SWITCH
1. Turn ignition switch OFF.
2. Disconnect oil pressure switch connector.
3. Check oil pressure switch. Refer to DI-36, "
OIL PRESSURE SWITCH" .
OK or NG
OK >> GO TO 4.
NG >> Replace oil pressure switch.
4. CHECK OIL PRESSURE SWITCH CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between IPDM E/R harness connector (A) and
oil pressure switch harness connector (B).
OK or NG
OK >> Replace IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
5. CHECK CAN COMMUNICATION
Select “METER” on CONSULT-II, and perform self-diagnosis of combination meter.
Self
-diagnostic results content
No malfunction detected>> GO TO 6.
Malfunction detected>> Check applicable parts, and repair or replace as necessary.
Te r m i n a l s
ConditionVoltage
(Approx.) (+)
(–)
IPDM E/R
connectorTe r m i n a l
E46 37 Ground Engine stopped 0 V
WKIA5458E
AB
Continuity
Connector Terminal Connector Terminal
E46 37 F32 1 Yes
WKIA5459E
Page 1144 of 2896

WARNING LAMPS
DI-35
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: June 20062007 Versa
6. CHECK COMBINATION METER INPUT SIGNAL
Select “METER” on CONSULT-II. Operate ignition switch with “OIL
W/L” of “DATA MONITOR” and check operation status.
OK or NG
OK >> Replace combination meter. Refer to IP-19, "COMBINA-
TION METER" .
NG >> Replace IPDM E/R. Refer to PG-29, "
Removal and
Installation of IPDM E/R" .
Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal)EKS00I0U
NOTE:
For oil pressure inspection, refer to LU-5, "
OIL PRESSURE CHECK" .
1. CHECK OIL PRESSURE WARNING LAMP OPERATION
Activate IPDM E/R auto active test. Refer to PG-21, "
Auto Active Test" .
Does oil pressure warning lamp blink?
YES >> GO TO 2.
NO >> GO TO 5.
2. CHECK IPDM E/R OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect oil pressure switch connector.
3. Turn ignition switch ON.
4. Check voltage between oil pressure switch harness connector
and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. CHECK OIL PRESSURE SWITCH
1. Turn ignition switch OFF.
2. Check oil pressure switch. Refer to DI-36, "
OIL PRESSURE SWITCH" .
OK or NG
OK >> Replace IPDM E/R. Refer to PG-29, "Removal and Installation of IPDM E/R" .
NG >> Replace oil pressure switch.“OIL W/L”
When ignition switch is in ON
position (Engine stopped.): ON
When engine running : OFF
PKIA2064E
Te r m i n a l s
Voltage (Approx.) (+)
(–)
Oil pressure switch
connectorTe r m i n a l
F32 1 Ground 12 V
PKIC11 44 E