2007 NISSAN LATIO headlamp

BCS-4
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
NOTE:
Headlamp has a dual system switch.
4. Example operation: (When lighting switch 1st position is turned ON)

When lighting switch 1st position is turned ON, contact in combination switch turns ON. At this time if
OUTPUT 4 transistor is activated, BCM detects that voltage changes in INPUT 5.

When OUTPUT 4 transistor is ON, BCM detects that voltage changes in INPUT 5, and judges lighting
switch 1st position is ON. Then BCM sends tail lamp ON signal to IPDM E/R using CAN communica-
tion.

When OUTPUT 4 transistor is activated again, BCM detects that voltage changes in INPUT 5 and rec-
ognizes that lighting switch 1st position is continuously ON.
SKIB7614E

BCM (BODY CONTROL MODULE)
BCS-7
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa

BCM is activated with low current consumption mode.

CAN communication is not active.

When CAN communication operation is detected, it switches to CAN communication status.

When a state of the following switches changes, it switches to CAN communication state:
–Ignition switch
–Key switch (without Intelligent Key)
–Key switch and ignition knob switch (with Intelligent Key)
–Hazard switch
–Door lock/unlock switch
–Front door switch (LH, RH)
–Rear door switch (LH, RH)
–Back door lock assembly
–Combination switch (passing, lighting switch 1st position, front fog lamp)
–Keyfob (lock/unlock signal)
–Front door key cylinder switch LH

When control performed only by BCM is required by switch, it shifts to CAN communication inactive
mode.

Status of combination switch reading function is changed.
SYSTEMS CONTROLLED BY BCM DIRECTLY

Power door lock system. Refer to BL-23, "POWER DOOR LOCK SYSTEM" .

Remote keyless entry system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Power window system. Refer to GW-17, "POWER WINDOW SYSTEM" . NOTE

Room lamp timer. Refer to LT- 9 1 , "INTERIOR ROOM LAMP" .

Rear wiper and washer system. Refer to WW-30, "REAR WIPER AND WASHER SYSTEM" .
NOTE:
Power supply only. No system control.
SYSTEMS CONTROLLED BY BCM AND IPDM E/R

Panic system. Refer to BL-54, "REMOTE KEYLESS ENTRY SYSTEM" .

Vehicle security (theft warning) system. Refer to BL-193, "VEHICLE SECURITY (THEFT WARNING)
SYSTEM" .

NVIS(NATS) system. Refer to BL-212, "NATS (Nissan Anti-Theft System)" .

Headlamp, tail lamp and battery saver control systems. Refer to LT- 7 5 , "PARKING, LICENSE PLATE AND
TA I L L A M P S" , LT- 5 , "HEADLAMP (FOR USA)" or LT-27, "HEADLAMP (FOR CANADA) - DAYTIME
LIGHT SYSTEM -" .

Front fog lamp. Refer to LT-41, "FRONT FOG LAMP" .

Front wiper and washer system. Refer to WW-4, "FRONT WIPER AND WASHER SYSTEM" .

Rear window defogger system. Refer to GW-50, "REAR WINDOW DEFOGGER" .
SYSTEMS CONTROLLED BY BCM AND COMBINATION METER

Warning chime. Refer to DI-47, "WARNING CHIME" .

Turn signal and hazard warning lamps. Refer to LT- 5 1 , "TURN SIGNAL AND HAZARD WARNING
LAMPS" .
SYSTEMS CONTROLLED BY BCM AND INTELLIGENT KEY UNIT

Intelligent Key system. Refer to BL-80, "INTELLIGENT KEY SYSTEM" .

BCS-8
BCM (BODY CONTROL MODULE)
Revision: June 20062007 Versa
MAJOR COMPONENTS AND CONTROL SYSTEM
CAN Communication System DescriptionEKS00I82
Refer to LAN-4, "SYSTEM DESCRIPTION" .
System Input Output
Remote keyless entry systemRemote keyless entry receiver
(keyfob)

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Intelligent Key system Intelligent Key unit

All door locking actuators

Turn signal lamp (LH, RH)

Combination meter (turn signal lamp)
Power door lock systemFront power door lock/unlock
switch (LH, RH)All door locking actuators
Power supply (IGN) to power window Ignition power supply Power supply to power window system
Power supply (BAT) to power window Battery power supply Power supply to power window system
Panic alarm

Key switch

KeyfobIPDM E/R
Battery saver control

Ignition switch

Combination switchIPDM E/R
Headlamp Combination switch IPDM E/R
Tail lamp Combination switch IPDM E/R
Front fog lamp Combination switch IPDM E/R
Turn signal lamp Combination switch

Turn signal lamp

Combination meter
Hazard lamp Hazard switch

Turn signal lamp

Combination meter
Room lamp timer

Key switch

Keyfob

Main power window and door
lock/unlock switch

Front door switch LH

All door switchInterior room lamp
Key warning chime

Key switch

Front door switch LHCombination meter (warning buzzer)
Light warning chime

Combination switch

Key switch

Front door switch LHCombination meter (warning buzzer)
Seat belt warning chime

Seat belt buckle switch LH

Ignition switchCombination meter (warning buzzer)
Front wiper and washer system

Combination switch

Ignition switchIPDM E/R
Rear window defogger Rear window defogger switch IPDM E/R
Rear wiper and washer system

Combination switch

Ignition switchRear wiper motor
A/C switch signal Front air control ECM
Blower fan switch signal Front air control ECM
A/C indicator signal Front air control A/C indicator
Low tire pressure warning system Remote keyless entry receiver Combination meter

BCM (BODY CONTROL MODULE)
BCS-17
C
D
E
F
G
H
I
J
L
MA
B
BCS
Revision: June 20062007 Versa
CONSULT-II Function (BCM)EKS00I87
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
ITEMS OF EACH PART
NOTE:
CONSULT-II will only display systems the vehicle possesses.
BCM diagnostic
test itemDiagnostic mode Content
Inspection by partWORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
MNTRThe results of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
System and itemCONSULT-II dis-
playDiagnostic test mode (Inspection by part)
WORK
SUPPORTSELF−
DIAG
RESULTSCAN DIAG
SUPPORT
MNTRDATA
MONITORECU
PA R T
NUMBERACTIVE
TESTCON-
FIGU-
RATION
BCM BCM×× × × ×
Power door lock sys-
temDOOR LOCK×××
Rear defoggerREAR DEFOG-
GER××
Warning chime BUZZER××
Room lamp timer INT LAMP×××
Remote keyless entry
systemMULTI REMOTE
ENT×××
Headlamp HEAD LAMP×××
Wiper WIPER×××
Turn signal lamp
Hazard lampFLASHER××
Blower fan switch sig-
nal
Air conditioner switch
signalAIR CONDI-
TIONER×
Intelligent KeyINTELLIGENT
KEY×
Combination switch COMB SW×
NVIS (NATS) IMMU××
Interior lamp battery
saverBATTERY
SAVER×××
Back door TRUNK××
Theft alarm THEFT ALARM×××
Retained accessory
power controlRETAINED PWR×××

BL-3
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa Check Warning Chime in Combination Meter ...... 156
Hazard Function Check ........................................ 157
Horn Function Check ........................................... 157
Headlamp Function Check ................................... 158
Intelligent Key Battery Replacement .................... 159
DISASSEMBLY AND ASSEMBLY OF INTELLI-
GENT KEY ........................................................ 159
INTELLIGENT KEY BATTERY INSPECTION ... 159
Remote Keyless Entry Function ........................... 159
Removal and Installation of Intelligent Key Unit ... 160
REMOVAL ......................................................... 160
INSTALLATION ................................................. 160
DOOR ..................................................................... 161
Fitting Adjustment ................................................ 161
FRONT DOOR .................................................. 161
REAR DOOR .................................................... 163
BACK DOOR ..................................................... 164
Removal and Installation ...................................... 165
FRONT DOOR .................................................. 165
REAR DOOR .................................................... 166
BACK DOOR ..................................................... 167
FRONT DOOR LOCK ............................................. 169
Component Parts Location ................................... 169
Removal and Installation ...................................... 169
REMOVAL ......................................................... 169
INSTALLATION ................................................. 171
REAR DOOR LOCK ............................................... 172
Component Parts Location ................................... 172
Removal and Installation ...................................... 172
REMOVAL ......................................................... 172
INSTALLATION ................................................. 174
BACK DOOR LOCK ............................................... 175
Component Parts and Harness Connector Location . 175
System Description .............................................. 176
Wiring Diagram — TLID — .................................. 177
WITHOUT INTELLIGENT KEY SYSTEM ......... 177
WITH INTELLIGENT KEY SYSTEM ................. 178
Terminals and Reference Values for BCM ........... 179
Terminals and Reference Values for Intelligent Key
Unit ....................................................................... 179
CONSULT-II Function (BCM) ............................... 179
CONSULT-II START PROCEDURE .................. 179
CONSULT-II APPLICATION ITEMS .................. 180
Work Flow ............................................................ 180
Trouble Diagnosis Chart by Symptom .................. 180
BCM Power Supply and Ground Circuit ............... 180
Check Back Door Opener Switch Circuit (Without
Intelligent Key or Power Windows) ...................... 181
Check Back Door Opener Switch Circuit (Without
Intelligent Key, With Power Windows) .................. 184
Check Back Door Opener Switch Circuit (With Intel-
ligent Key) ............................................................ 187
Check Back Door Lock Assembly (Actuator) Circuit . 189
Removal and Installation ...................................... 190
BACK DOOR LOCK .......................................... 190
BACK DOOR HANDLE ..................................... 191FUEL FILLER LID OPENER ...................................192
Removal and Installation of Fuel Filler Lid Opener .192
REMOVAL .........................................................192
INSTALLATION .................................................192
VEHICLE SECURITY (THEFT WARNING) SYSTEM .193
Component Parts and Harness Connector Location .193
System Description ...............................................194
DESCRIPTION ..................................................194
POWER SUPPLY AND GROUND ....................194
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ...................................................................195
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ................................................................195
VEHICLE SECURITY SYSTEM DEACTIVATION .195
PANIC ALARM OPERATION ............................195
CAN Communication System Description ............196
Schematic .............................................................197
Wiring Diagram — VEHSEC — ............................198
..........................................................................198
Terminals and Reference Values for BCM ............202
Terminals and Reference Values for Intelligent Key
Unit .......................................................................202
CONSULT-II Function (BCM) ...............................202
CONSULT-II START PROCEDURE ..................202
CONSULT-II APPLICATION ITEM ....................202
Trouble Diagnosis .................................................204
WORK FLOW ....................................................204
Preliminary Check ................................................205
Symptom Chart .....................................................206
Diagnostic Procedure 1 ........................................207
Diagnostic Procedure 2 ........................................210
Diagnostic Procedure 3 ........................................211
Diagnostic Procedure 4 ........................................211
Diagnostic Procedure 5 ........................................211
Diagnostic Procedure 6 ........................................211
NATS (NISSAN ANTI-THEFT SYSTEM) ................212
Component Parts and Harness Connector Location .212
System Description ...............................................213
DESCRIPTION ..................................................213
SECURITY INDICATOR ....................................213
System Composition .............................................213
ECM Re-communicating Function ........................214
Wiring Diagram — NATS — .................................215
Terminals and Reference Values for BCM ............216
CONSULT-II Function ...........................................216
CONSULT-II INSPECTION PROCEDURE ........216
CONSULT-II DIAGNOSTIC TEST MODE FUNC-
TION ..................................................................217
HOW TO READ SELF-DIAGNOSTIC RESULTS .217
NATS SELF-DIAGNOSTIC RESULTS ITEM
CHART ..............................................................218
Trouble Diagnosis Procedure ...............................219
PRELIMINARY CHECK .....................................219
WORK FLOW ....................................................220
Trouble Diagnoses ...............................................222
SYMPTOM MATRIX CHART 1 ..........................222
SYMPTOM MATRIX CHART 2 ..........................222
Diagnostic Procedure 1 ........................................223
Diagnostic Procedure 2 ........................................225

BL-14
HOOD
Revision: June 20062007 Versa
HOODPFP:F5100
Fitting AdjustmentEIS0090O
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1. Remove the front grille. Refer to EI-19, "FRONT GRILLE" .
2. Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3. Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4. Install the front grille. Refer to EI-19, "
FRONT GRILLE" .
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1. Remove the front grille. Refer to EI-19, "FRONT GRILLE" .
2. Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3. Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
4. Press the hood lightly with [approx. 29 N (3 kg] of force and adjust A and B as shown.
PIIB6508E
Hood and headlamp (B - B) : Less than 2.0 mm (0.08 in)
Hood and fender (C - C) : Less than 1.5 mm (0.06 in)
Hood and fender (D - D) : Less than 1.5 mm (0.06 in)
PIIB2526J
Hood and front bumper (A - A) : -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D) : -0.4 - 1.7 mm (-0.16 - 0.07 in)

BL-20
RADIATOR CORE SUPPORT
Revision: June 20062007 Versa
RADIATOR CORE SUPPORTPFP:62500
Removal and InstallationEIS0090S
REMOVAL
Radiator Core Support Upper
1. Remove the air duct. Refer to EM-16, "Removal and Installation" .
2. Remove the headlamp (LH/RH). Refer to LT-25, "
Removal and Installation" .
3. Remove the hood lock assembly, and remove hood lock cable. Refer to BL-17
.
4. Remove the air guide and hood lock cable clip.
5. Remove the washer tank inlet. Refer to WW-28, "
Removal and Installation of Washer Tank" .
6. Remove the radiator core support upper.
Radiator Core Support Lower
1. Remove the air duct. Refer to EM-16, "Removal and Installation" .
2. Remove the front bumper. Refer to EI-14, "
Removal and Installation" .
3. Remove the headlamp (LH/RH). Refer to LT-25, "
Removal and Installation" .
4. Remove the hood lock assembly, and remove hood lock cable. Refer to BL-17
.
5. Remove the air guide and hood lock cable mounting clip.
6. Remove the front bumper reinforcement. Refer to EI-14, "
Removal and Installation" .
7. Remove the radiator core lower stay.
8. Remove the undercover.
PIIB6515E
1. Radiator core support upper 2. Radiator core support lower 3. Radiator core support lower stay
4. Radiator core support side stay 5. Air guide
24.5 N·m (2.5 kg-m, 18 ft-lb)

BL-22
FRONT FENDER
Revision: June 20062007 Versa
FRONT FENDERPFP:63100
Removal and InstallationEIS0090T
REMOVAL
1. Remove the headlamp assemblies. Refer to LT- 2 5 , "Removal and Installation" .
2. Remove the cowl top cover (LH/RH). Refer to EI-20, "
Removal and Installation" .
3. Remove the front fender protector. Refer to EI-22, "
Components" .
4. Remove the bolt and the front fender.
CAUTION:
While removing use a shop cloth to protect the vechicle body from damage.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:

After installing, apply touch-up paint onto the head of the front fender bolts.

After installing, check front fender adjustment. Refer to BL-14, "Fitting Adjustment" and BL-161,
"Fitting Adjustment" .
1. Front fender 2 Bolt (LH 7 bolts required) (RH 8
bolts required)
LIIA2657E