1998 SSANGYONG MUSSO Workshop Repair Manual

M162 ENGINE CONTROLS 1F1-71
If the measured value is not within the specified value, the
possible cause may be in cable or HFM sensor in itself.
Perform the 5V power supply inspection procedures.
HFM Sensor 5V Power Supply Inspection
1. Measure the voltage between the HFM sensor No.108(+) and
No.105(-) after removing the HFM sensor connector.
HFM Sensor Input Voltage Inspection
1. Measure the HFM sensor signal voltage between the ECU
terminal No.103 and No.104.
Specified Value (coolant temperature is over 70°C)
If the measured value is not within the specified value, the
possible cause may be in cable or ECU coupling.
Iginition"ON” 0.9 - 1.1 V
Engine at Idle 1.3 - 1.7 V
Specified Value 4.7 - 5.2 V
2. Measure the voltage between the HFM sensor wining
connector terminal No.3 pin(-) and No.4 after removing the
HFM sensor connector.
Specified Value
If the measured value is not within the specified value, the
possible cause may be in cable or over voltage protection
relay.
Perfrom the 12V power supple inspection procedures.
Specified Value 4.7 - 5.2 V
HFM Sensor 12V Power Supply Inspection
1. Measure the voltage between the HFM sensor wiring
connector 1G No.2 pin(+) and No.104 after removing the
HFM sensor connector.
If the measured value is not within the specified value, the
possible cause may be in cable or over voltage protection
relay.
Specified Value 11 - 14 V

1F1-72 M162 ENGINE CONTROLS
OXYGEN SENSOR
1 Electricity Wire
2 Oxygen Sensor Housing
3 Sensor Ceramic
4 Electrode (Internal)
5 Electrode (External)
6 Heating Coil
7 Open Space
8 Protector Tube
Functions
The oxygen sensor optimizes the combustion (Air-Fuel Ratio
14.7:1) and resets the Air-fuel ratio in the ECU after sensing
the amount of oxygen from the exhaust gases to diminish the
exhaust gases.
- Rich(<1) above approx. 450mV
- Lean(>1) below approx. 450mV
Locatoin of Sensor
Oxygen sensor is located on the front exhaust pipe.

M162 ENGINE CONTROLS 1F1-73
Oxygen Sensor Signal Voltage Inspection
1. Measure the oxygen sensor signal voltage between the ECU
terminal No.11 and No.9. Maintain the engine speed ia at
idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Voltage Inspection
1. Measure the oxygen sensor heating voltage between the
ECU terminal No.11 and No.9. Maintain the engine speed ia
at idle while the coolant temperature is over 80°C.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Oxygen Sensor Heating Current Consumption
Inspection
1. Measure the oxygen sensor heating current consumption
between the ECU terminal No.9 and No.5 while the ignition
switch is in "ON" position.
If the measured value is not within the specified value, the
possible cause may be in cable, oxygen sensor or ECU.
Specified Value 0.2 - 2.0 A
Specified Value -0.2 - 1.0 V
Specified Value 11 - 14

1F1-74 M162 ENGINE CONTROLS
KNOCK SENSOR
Functions
Vibration of the engine block is transmitted to the sensor and
transferred to the ECU in the form of an alternating voltage
signal via a shielded cable. The knock sensor is fastened to
the engine block to recognize knocking in all cylinders. The
ECU compares the signal and the retards firing point.
Removal & Installation Procedure
1. Disconnect the knock sensor connector from the intake
manifold bracket.
2. Unscrew the mounting bolt (M8 X 28) from the knock sensor
installed on the cylinder block and remove the knocking
sensor.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE CONTROLS 1F1-75
COOLANT TEMPERATURE SENSOR
1 Artificial Resin Housing
2 Metal Housing
3 NTC (negative temperature coefficient) Resistor
Removal & Installation Procedure
1. Remove the pressure by opening the pressure cap in the
coolant subtank.
2. Disconnect the connector and remove the coolant
temperature sensor.
Installation Notice
Replace the seals with new one.
3. Installation should follow the removal procedure in the
reverse order.
4. Check for leaks at each connections after starting the engine.4 Connector
5 Coolant Temperature Sensor
Tightening Torque 18 - 22 Nm

1F1-76 M162 ENGINE CONTROLS
2. Measure the resistance between the coolant temperature
sensor terminal No.1 and No.4 with the coolant temperature
sensor disconnected.
Inspection
1. Measure the coolant sensor input voltage between the ECU
terminal No.79 and No.78 while the ignition switch in "ON"
position.
Notice
Replace wiring and coolant temperature sensor if out of
specified value.
allowable error :±5%
allowable error :±5%
Voltage (V)
3.57
1.22
0.78
Temperature (°C)
20
30
40
Resistance (W)
2,500
322
185
Temperature (°C)
20
30
40

M162 ENGINE CONTROLS 1F1-77
Service Data
Resistance characteristic curve according to the coolant
temperatureTemperature(°C) Resistance(W) Voltage(V) Temperature(°C) Resistance(W) Voltage(V)
-40 48,550 4.8991 60 594 1.8632
-30 27,000 4.8214 70 434 1.5132
-20 15,670 4.7001 80 322 1.2179
-10 9,450 4.5215 90 243 0.9775
0 5,890 4.4273 100 185 0.7806
10 3,790 3.9562 110 143 0.6255
20 2,500 3.5714 120 111.6 0.5020
30 1,692 3.1426 130 88.0 0.4044
40 1,170 2.6959 140 71.2 0.3323
50 826 2.2618 - - -

1F1-78 M162 ENGINE CONTROLS
ACCELERATOR PEDAL MODULE
1 Accelerator pedal
2 Accelerator pedal Sensor
3 Bolts (2 Pieces).......................................4-8 Nm
Removal and Installation Procedure
1. Disconnect the 6-pin connector(arrow).
2. Unscrew the 2 bolts (3) / 1 nut (6) and remove the pedal
and sensor assembly.
Installatoin Notice
Tightining Torque 4 - 8 Nm
2. Installation should follow the removal procedure in the
reverse order.4 6-Pin Connector
5 Kick down Switch
6 Nut (1 piece)............................................4-8 Nm