1998 SSANGYONG MUSSO Workshop Repair Manual

4A-14 HYDRAULIC BRAKES
LCRV SETTING METHOD
1. LCRV setting should be performed with unladen vehicle
condition.
2. Install the connecting rod (a) to the No.1 hole.
Tightening Torque14 - 18 Nm
3. Adjust the clearance “X” to be 0 mm and tighten the bolt (c)
using the lock nut (b).
Tightening Torque 14 - 18 Nm
4. Remove the connecting rod (a) from the No.1 hole and
reinstall it to the No. 2 hole.
5. Place alignment marks between the lock nut (b) and
adjusting screw (c) after the valve setting.

SECTION 4B
MASTER CYLINDER
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4B-1
Fastener Tightening Specifications . . . . . . . . . 4B-1
Maintenance and Repair . . . . . . . . . . . . . . . 4B-2
TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Master Cylinder Nut
Booster NutN
· ·· ·
·m
14 - 22
8 - 18
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4B-2
Booster & Brake Master Cylinder . . . . . . . . . . 4B-2

4B-2 MASTER CYLINDER
1 Nut .......................................................14-22 Nm
2 Washer
3 Master Cylinder Assembly
4 Oil Level Sensor
5 Check Valve
6 Booster
7 Clevis Pin
8 Snap Pin9 Seal
10 Spacer
11 Nut .........................................................8-18 Nm
12 Front Tube (LH)
13 Front Tube (RH)
14 Rear Tube
15 1st Tube (Primary)
16 2nd Tube (Secondary)
MANDO
PBR
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
BOOSTER AND BRAKE MASTER CYLINDER

MASTER CYLINDER 4B-3
Removal & Installation Procedure
1. Remove the oil level sensor connector.
2. Remove the tube from the master cylinder.
Installation Notice
Notice
lBe careful not to drop the oil when removing the tube.
lIf the oil is dropped, promptly sweep up.
3. Remove the booster vacuum hose.
Notice
lConnect fully to the end of vacuum hose when installing.
4. Loosen the nut of master cylinder.
Installation Notice
5. Remove the clevis pin and disconnect the pedal and brake
booster push rod.
Notice
lInstall in the upper hole when PBR brake.
lConnect the snap pin in the hole of clevis pin fully.
lApply the grease around the hole of clevis pin.
Tightening Torque 14 - 22 Nm
Tightening Torque 15 - 19 Nm

4B-4 MASTER CYLINDER
6. Loosen the nut of booster and remove the booster from the
dash panel.
Installation Notice
Tightening Torque 8 - 18 Nm
7. Installation should follow the removal procedure in the
reverse order.
8. Add the fluid and bleed.
9. If necessary, adjust the pedal height, pedal stroke and free
play.

SECTION 4C
POWER BOOSTER
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4C-1
General Specifications . . . . . . . . . . . . . . . . . . 4C-1
Maintenance and Repair . . . . . . . . . . . . . . . 4C-2
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Type
RatioN
· ·· ·
·m
Vacuum Assisted
5.6 : 1
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4C-2
Booster & Brake Master Cylinder . . . . . . . . . . 4C-2
Pedal Stroke Inspection . . . . . . . . . . . . . . . . . 4C-5

4C-2 POWER BOOSTER
1 Nut .......................................................14-22 Nm
2 Washer
3 Master Cylinder Assembly
4 Oil Level Sensor
5 Check Valve
6 Booster
7 Clevis Pin
8 Snap Pin
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
BOOSTER AND BRAKE MASTER CYLINDER
9 Seal
10 Spacer
11 Nut .........................................................8-18 Nm
12 Front Tube (LH)
13 Front Tube (RH)
14 Rear Tube
15 1st Tube (Primary)
16 2nd Tube (Secondary)
MANDO
PBR

POWER BOOSTER 4C-3
Removal & Installation Procedure
1. Remove the oil level sensor connector.
2. Remove the tube from the master cylinder.
Installation Notice
Notice
lBe careful not to drop the oil when removing the tube.
lIf the oil is dropped, promptly sweep up.
3. Remove the booster vacuum hose.
Notice
lConnect fully to the end of vacuum hose when installing.
4. Loosen the nut of master cylinder.
Installation Notice
5. Remove the clevis pin and disconnect the pedal and brake
booster push rod.
Notice
lInstall in the upper hole when PBR brake.
lConnect the snap pin in the hole of clevis pin fully.
lApply the grease around the hole of clevis pin.
Tightening Torque 14 - 22 Nm
Tightening Torque 15 - 19 Nm