1998 SSANGYONG MUSSO Workshop Repair Manual

REAR DRIVE AXLE 3D-15
Inspection of Ring Gear Tooth Contact Pattern
Normal Contact
Apply gear-marking compound (prussian blue / red lead) on
the ring gear teeth. Rotate the ring gear and check the tooth
contact pattern.
Abnormal Contact
Tooth Contact patternPossible CauseRemedy
1. Heel Contact
2. Toe Contact
3. Face Contact
4. Flank ContactInsufficient backlash (little)
lTooth can be damaged
or broken under heavy
load
Excessive backlash (much)
lDrive pinion shaft is apart
from the ring gear
lNoise can be occurred
Insufficient backlash (much)
lGear contacts on the low
flank
lGear can be damaged or
worn
lNoise can be occurredAdjust backlash(Decrease backlash)
lSelect proper shim(s) to move the
drive pinion toward the ring gear
(toward toe)
Adjust backlash(Increase backlash)
lSelect proper shim(s) to move the
drive pinion against the ring gear
(toward heel)
Adjust backlash(Increase pinion shim)
lMove the drive pinion toward the ring
gear (toward center of ring gear)
Adjust backlash(Decrease pinion shim)
lMove the ring gear toward the drive
pinion (toward ring gear center line) Excessive backlash (little)
lNoise can be occurred

3D-16 REAR DRIVE AXLE
LSD (LIMITED SLIP DIFFERENTIAL)
1 Limited Slip Differential Assembly
2 Shaft, Hub (left)
3 Shim
4 Thrust Washer
5 Face Cam (left)
6 Cam Whillom
7 Thrust Bearing
8 Radial Bearing9 Shaft, Hub (right)
10 Thrust Washer
11 Face Cam (right)
12 Cage
13 Thrust Bearing
14 Plate Spring
15 Radial Bearing
16 Oil Catcher

REAR DRIVE AXLE 3D-17
Inspection
lRemove the LSD assembly and check the pre-load torque.
lIf necessary, replace LSD assembly.
Procedure
1. Fix the right shaft of LSD to the special tool (A).
2. Install the special tool (B) to the left shaft and rotate
counterclockwise and check the pre-load torque.
Normal Torque 3.6 - 9.0kgm
Notice
If necessary, replace LSD assembly.

SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3
TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay
Type
Inner Diameter
Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
Operation
SpecificationPBR Brake
4.3 : 1
132 mm
f23.81 mm
5.0 : 1
f60.4 mm
¬
f40.5 mm
9.5 mm
¬ Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc
10 mm
24 mm
Rear Wheel Internal Expansion Type
Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder
Brake Booster
Front Brake
Rear Brake
Parking Brake
Brake FluidMANDO Brake
4.3 : 1
138 mm
f25.4 mm
5.6 : 1
f60 mm
Solid Disc
f38.2 mm
10.0 mm
10.4 mm
Application

4A-2 HYDRAULIC BRAKES
Check
Dirty or Lack of Fluid
Air in Brake System
Faulty Brake Booster
Poor Contact of Pad or Lining
Oil or Grease on Pad
Faulty Auto Adjuster
Over Heated Rotor Due to Dragging Pad or Lining
Clogging Brake Line
Faulty Proportioning ValveCheck
Incorrect Tire Pressure Between Left and Right
Poor Contact of Pad or Lining
Oil or Grease is Applied to Pad or Lining
Bent or Uneven Wear of Drum
Incorrectly Mounted Wheel Cylinder
Faulty Auto AdjusterAction
Repair
Retighten
Replace
Replace
Repair
Repair
Lubricate
Retighten Check
Incorrectly Mounted Back Plate or Caliper
Loosened Bolt of Back Plate or Caliper
Crack or Uneven Wear of Brake Drum or Disc
Pad or Lining Sticking to Contact Surface
Excessive Clearance Between Caliper and Pad
Uneven Contact of Pad
Lack of Lubrication
Loosened Suspension
DIGNOSIS
NOISE OR VEHICLE VIBRATION WHEN APPLIED BRAKE
PULLS TO ONE SIDE WHEN BRAKING
Action
Adjust
Repair
Replace
Replace
Repair
Replace
Action
Replenish or Replace(Check eventual leakage)
Bleeding
Replace
Repair
Replace
Replace
Repair
Repair
Repair
POOR BRAKING
( If low cut-in : Adjust )
( If Leakage : Replace )

HYDRAULIC BRAKES 4A-3
Check
Air in Brake system
Fluid Leaking
Excessive Clearance Between Push Rod and M/cylinder
Parking Brake is not Fully Released
Incorrect Adjustment of Parking Brake
Weak Return Spring of Brake Pedal
Incorrect Pedal Freeplay
Broken Rear Drum Brake Shoe Return Spring
Lack of Lubrication
Damaged Master Cylinder Check Valve or Piston Return SpringAction
Bleeding
Repair
Adjust
Repair
Adjust
Replace
Repair
Replace
lubricate
Replace
INCREASING PEDAL STROKE (PEDAL GOES TO FLOOR)
OR BRAKE DRAGGING
Check
Insufficient Clearance Between Push Rod and Master Cylinder
Worn Brake Lining
Oil or Grease on Lining
Binding Parking Brake Cable
Faulty Auto Adjuster
Excessive Lever StrokeAction
Adjust
Replace
Replace
Replace
Replace
Adjust or Check Cable
POOR BRAKING OF PARKING BRAKE

4A-4 HYDRAULIC BRAKES
COMPONENT LOCATOR
ABS
1 Actuation Assembly (Booster+TMC)
2 ABS Control Unit
3 Master Cylinder 2nd Tube (Secondary)
4 Master Cylinder 1st Tube (Primary)
5 Front Tube (LH)
6 Front Tube (RH)7 Brake Hose
8 Rear Tube
9 Bolt......................................................25-35 Nm
10 2-way Connector
11 3-way Connector

HYDRAULIC BRAKES 4A-5
ABS / ABD
1 Actuation Assembly (Booster+TMC)
2 Master Cylinder 1st Tube (Primary)
3 Master Cylinder 2nd Tube (Secondary)
4 Hydraulic Modulator
5 Front Tube (LH)6 Front Tube (RH)
7 Rear Tube (RH)
8 Rear Tube (LH)
9 2-way Connector