1998 SSANGYONG MUSSO Workshop Repair Manual

M162 ENGINE INTAKE & EXHAUST 1G1-5
INTAKE MANIFOLD
Preceding Work : Removal of fuel distributor and injection valve
1 Bolt (M6 X 40, 4 pieces)......................... 9-11 Nm
2 Softcap
3 Resonance Flap
4 Gasket ................................................... Replace
5 Upper Intake Manifold
6 Bolt (M8 x 50, 9 pieces).................22.5-27.5 Nm
7 Gasket ................................................... Replace
8 Blow-by Hose
9 Blow-by Hose
1 0 Clamp
11 Blow-by Nipple
12 Inlet Air Housing13 Bolt (M6 x 40, 4 pieces)......................... 9-11 Nm
14 Throttle Body - Electric
15 Gasket ................................................... Replace
16 Lower Intake Manifold.........................................
17 Bolt (M8 x 40, 4 pieces).................22.5-27.5 Nm
1 8 Nipple.................................................... Replace
19 Seal Ring
20 Connection House
2 1 Clamp
22 Noise Damper Assembly
23 Tapping Screw

1G1-6 M162 ENGINE INTAKE & EXHAUST
Removal & Installation Procedure
lUpper Intake Manifold
1. Disconnect the vacuum hose (8,9).
2. Loosen the clip (22).
3. Remove the upper intake manifold (5) after unscrewing the
bolt (6).
Installation Notice
Notice
Check the gasket and replace it if necessary.
4. Installation should follow the removal procedure in the
reverse order.
lLower Intake Manifold
Preceding work : removal of upper intake manifold
1. Remove the hose of brake booster vacuum line and idle
speed connector.
2. Disconnect the hot water inlet pipe from the bottom of lower
intake manifold.
3. Unscrew the bolt (17) and remove the lower intake manifold
(16).
Installation Notice
4. Start the engine and check for leaks at each connection
part.
Tightening Torque 22.5 - 27.5 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE INTAKE & EXHAUST 1G1-7
RESONANCE FLAP
1 Soft Cap (2)
2 Bolt (M6 x 25, 4 pieces)......................... 9-11 Nm
3 O-ring
Removal & Installation Procedure
1. Remove the 2 soft caps (1).
2. Remove the upper resonance flap coupling after removing
4 bolts (2).
Notice
Connect carefully the vacuum hose (4) for installation.
3. Check the O-ring (3) and replace it if necessary.
4. Remove the lower resonance flap (5).
5. Replace the gasket (6).
6. Installation should follow the removal procedure in the
reverse order.4 Vacuum Hose
5 Resonance Flap
6 Gasket ................................................... Replace

1G1-8 M162 ENGINE INTAKE & EXHAUST
Function Description
A pneumatically actuated resonance flap (5) is located on the
intake manifold, and will be opened and closed by load, which
operates resonance flap according to engine and controlled
by ECU and rpm.
1. Resonance flap closed (at idle/partial load : less than
3,800/rpm)
The switch valve (7) will be adjusted by ECU and resonance
falp will be colosed. By increasing air flow passage through
dividing intaking air flow toward both air collection housing
(8). This leads to a signficant increase in the torque in the
lower speed range.
2. Resonance flap open (at full load : over 3,800/rpm)
The switch valve (7) will not be adjusted by ECU and
resonance falp (5) will be open. The colllected air in the air
collection housing (8) will not be divided and intaking air
passage will be shorten.

M162 ENGINE INTAKE & EXHAUST 1G1-9
EXHAUST MANIFOLD
Preceding Work : Removal of air cleaner
1 Nut .......................................................36-44 Nm
2 Gasket ................................................... Replace3 Exhaust Manifold

1G1-10 M162 ENGINE INTAKE & EXHAUST
Tools Required
103 589 01 39 00 Caulking Bolt
Removal & Installation Procedure
1. Remove the flange bolt from the exhaust manifold, and
disconnect the front exhaust pipe.
Installation Notice
Notice
Check for nut damages and replace the nut if necessary.
2. Remove the 23 nuts (1) from the stud bolt, and remove the
exhaust manifold.
Installation Notice
3. Replace the gasket (2).
4. Installation is reverse order of the removal.
Replacement of Rivet Nut
1. Pull out the rivet nut from the connecting point of the exhaust
manifold and the exhaust pipe using a proper bolt (arrow).
2. Insert a new rivet nut into the exhaust manifold hole, and
tighten with a special tool (Caulking Bolt).
Installation Notice
Caulking Bolt 103 589 01 39 00
Tightening Torque 30 Nm
Tightening Torque 26 - 34 Nm
Tightening Torque 30 Nm

M162 ENGINE INTAKE & EXHAUST 1G1-11
Removal and Installation of Exhaust Line
1 Exhaust Manifold
2 Rivet Nut
3 Bolt........................................................... 30 Nm
4 Front Pipe
5 Oxygen Sensor
6 Bolt......................................................28-47 Nm
7 Rubber Pad
8 Catalytic Converter
9 Gasket ................................................... Replace1 0 Nut
11 Gasket ................................................... Replace
12 Rubber Pad
13 Nut .......................................................28-47 Nm
14 Center Muffler
15 Rubber Pad
16 Tail Muffler
17 Gasket ................................................... Replace
18 Nut .......................................................28-47 Nm

SECTION 1G2
M161 ENGINE INTAKE & EXHAUST
TABLE OF CONTENTS
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Nlm
9 - 11
22.5 - 27.5
22.5 - 27.5
9.5 - 12.5
15 - 28
28 - 47 Application
Air Cleaner Housing Cover Nut
Intake Manifold Bolt (M8 x 20)
Intake Manifold Bolt (M8)
Exhaust Mainfold Stud Bolt
Exhaust Pipe Nut (Engine)
Exhaust Pipe Bolt
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G2-1
Fastener Tightening Specifications . . . . . . . . 1G2-1
Maintenance and Repair . . . . . . . . . . . . . . 1G2-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G2-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G2-2Air Intake Shield . . . . . . . . . . . . . . . . . . . . . . 1G2-4
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G2-5
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G2-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G2-9