1998 SSANGYONG MUSSO Workshop Repair Manual

OM600 ENGINE MECHANICAL 1B3-67
Installation Procedure
1. Thoroughly clean the sealing surface and apply sealant.
2. Install the timing case cover.
Notice
Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque 10 Nm
Tightening Torque 23 Nm
4. Tighten the oil pan bolts.
Tightening Torque10 Nm
10 Nm
23 Nm
Socket bolt
M6 bolt
M8 bolt

1B3-68 OM600 ENGINE MECHANICAL
Tightening Torque25 Nm 5. Install the flange, vibration damper and crankshaft belt
pulley.
Notice
Replace front radial seal if necessary.
6. Install the alternator bracket.
25 Nm Front
Side
7. Install the alternator
Tightening TorqueUpper - 25 Nm
Low - 25 Nm
8. Install the cylinder head cover.
Tightening Torque 10 Nm
9. Tighten the injection pump mounting bolts.
Tightening Torque 23 Nm

OM600 ENGINE MECHANICAL 1B3-69
10. Install the fuel filter.
11. Install the vacuum pump.
12. Install the power steering pump.
13. Install the power steering pump pulley.
Tightening Torque 25 Nm
Tightening Torque 10 Nm
Tightening Torque 23 Nm
Tightening Torque 32 Nm
14. Install the guide pulley bracket.
Tightening Torque 9 Nm

1B3-70 OM600 ENGINE MECHANICAL
15. Install the guide pulley (22) and fit the closing cover (20).
16. Replace the gasket (3) and install the cylinder head cover
(2).
17. Install the cooling fan belt pulley and fan clutch.
18. Install the belt tensioning device and then install the belt.
19. Install the cooling fan.
20. Fill the engine oil and check oil leaks by running the engine.
Tightening Torque 23 Nm
Tightening Torque 10 Nm

OM600 ENGINE MECHANICAL 1B3-71
CRANKSHAFT END COVER
Preceding Work : Removal of flywheel and driven plate.
1 Crankshaft Flange
2 End Cover..............................Clean, Loctite 573
3 Bolt.........................................10Nm, Loctite 5734 Radial Seal............................................ Replace
5 Dowel Sleeve
6 Bolt.........................................10Nm, Loctite 573

1B3-72 OM600 ENGINE MECHANICAL
Tools Required
601 589 03 43 00 Oil Seal Assmbler
Removal Procedure
1. Remove the bolts (3, 6) from end cover, By pulling out the
lugs (arrow), remove the cover.
Notice
Be careful not to damage the oil pan gasket.
2. Remove the radial seal (4) with care not to damage the
sealing surface.
Installation Procedure
1. Thoroughly clean the sealing surface of end cover and apply
Loctite 573.
2. Clean the groove of radial seal.
3. Apply Loctite 573 on the bolts and install the end cover.
Tightening Torque 10 Nm
Notice
Be careful not to damage the oil pan gasket.
4. Install the inner oil seal assembler to the crankshaft flange.
Oil Seal Assembler 601 589 03 43 00

OM600 ENGINE MECHANICAL 1B3-73
Notice
The sealing lip of the repair radial seal is offset to the inside
by 3mm to ensure that it does not run in any groove which
the standard radial seal may have left on the crankshaft
flange.
7. Install the outer oil seal assembler on he seal and by
tightening the bolts, press the radial seal into the end cover
as far as the stop.
Notice
The seal must be positioned exactly at right angles in the
end cover to ensure that it provides a proper seal.
Oil Seal Assembler 601 589 03 43 00 A Standard Radial Seal
B Repair Radial Seal
5. Coat a little oil on the sealing lip of new radial seal and
contacting surface.
Notice
Don’t use grease.
6. Insert the new radial seal (4) onto the oil seal assembler
(7).

1B3-74 OM600 ENGINE MECHANICAL
VIBRATION DAMPER AND HUB
Preceding Work : Removal of the cooling fan
Removal of poly V-belt
1 Bolt............................................................10Nm
2 Cooling Fan Belt Pulley
3 Socket Bolt................................................23Nm
4 Crankshaft Belt Pulley
5 Vibration Damper6 Bolt................................................200Nm + 90°
7 Washer
8 Straight Pin
9 Hub
10 Oil Pan