1998 SSANGYONG MUSSO four wheel drive

5A-42 AUTOMATIC TRANSMISSION
POWER TRAIN SYSTEM
The Power Train System consists of:
lA torque converter with single face lock-up clutch
lFour multi-plate clutch assemblies
lTwo brake bands
lTwo one-way clutches
lPlanetary gearset
lParking mechanism
A conventional six pinion Ravigneaux compound planetary gearset is used with overdrive (fourth gear) being obtained
by driving the carrier.
The cross-sectional arrangement is very modular in nature. Four main sub-assemblies are installed within the case
to complete the build. These sub-assemblies are:
lGearset-sprag-centre support
lC1 -C2-C3-C4 clutch sub-assembly
lPump assembly
lValve body assembly
One, or a combination of selective washers are used between the input shaft flange and the number 4 bearing to
control the transmission end float. This arrangement allows for extensive subassembly testing and simplistic final
assembly during production.
A general description of the operation of the Power Train System is detailed below. Refer to table 4.1 and figure 4.1.
First gear is engaged by applying the C2 clutch and locking the 1-2 One Way Clutch (1-2 OWC). The 1-2 shift is
accomplished by applying the B1 band and overrunning the 1-2 OWC. The 2-3 shift is accomplished by applying the
C1 clutch and releasing the B1 band. The 3-4 shift is accomplished by re-applying the B1 band and overrunning the
3-4 OWC. Reverse gear is engaged by applying the C3 clutch and the B2 band.
The C4 clutch is applied in the Manual 1,2 and 3 ranges to provide engine braking. In addition, the C4 clutch is also
applied in the Drive range for second and third gears to eliminate objectionable freewheel coasting. The B2 band is
also applied in the Manual 1 range to accomplish the low-overrun shift.
Both the front and rear servos are dual area designs to allow accurate friction element matching without the need for
secondary regulator valves. All the friction elements have been designed to provide low shift energies and high static
capacities when used with the new low static co-efficient transmission fluids. Non-asbestos friction materials are used
throughout.
Gear
First
Second
Third
Fourth
Reverse
Manual 1Gear
Ratio
2.741
1.508
1.000
0.708
2.428
2.741C1
X
XC2
X
X
X
X
XC3
XC4
X
XB1
X
X
XB2
X
X1-2
OWC
X3-4
OWC
X
X
XLU
CLUTCH
X*
X ELEMENTS ENGAGED
* For Certain Vehicle Applications, Refer to the Owner's Manual. Table 4.1 - Engaged Elements vs Gear Ratios

5A-44 AUTOMATIC TRANSMISSION
CLUTCH PACKS
There are four clutch packs (refer to figure 4.3). All clutch packs are composed of multiple steel and friction plates.
C1 CLUTCHWhen applied, this clutch pack allows the input shaft to drive the planet carrier.
This occurs in third and fourth gears.
C2 CLUTCHWhen applied this clutch pack allows the input shaft to drive the forward sun gear via the 3-4 OWC.
This occurs in all forward gears.
C3 CLUTCHWhen applied this clutch pack allows the input shaft to drive the reverse sun gear. This only occurs in
reverse gear.
C4 CLUTCHWhen applied this clutch provides engine braking on overrun. This occurs in Manual 1, 2 and 3 and
also Drive 2 and Drive 3 to prevent objectionable free wheel coasting.
Figure 4.3 - Clutch Packs

5D1-36 TRANSFER CASE (PART TIME 4408)
TRANSFER CASE CONTROL UNIT
(TCCU)
System Description
TCCU is located under the front left handed seat and permits
the vehicle to shift from two-wheel drive to four-wheel drive
(and back shift) according to driver’s switch operation during
driving (For the shifting between 4WD HIGH and 4WD LOW,
stop the vehicle).
1. Shifting from 2H to 4H
lPosition the transfer case switch from '2H' to '4H'.
lShifting is possible during driving.
l'4WD Hl' indicator light will turn on.
2. Shifting from 4H to 2H
lPosition the transfer case switch from '4H' to '2H'.
lShifting is possible during driving.
l'4WD Hl' indicator light will turn off.
3. Shifting between 4H and 4L
lShifting is possible when the vehicle is almost stopped
(below approx. 2 km/h), so it would be better stop the
vehicle.
lIn case of manual transmission equipped vehicle, apply
clutch pedal.
lIn case of auto transmission equipped vehicle, put the
lever position into 'N'.
lPosition the transfer case switch '4H' to '4L' or '4L' to
'4H'.
lAccording to the shifted position, indicator light will turn
on.
Notice
If there are malfunctions during shifting,'4H' or '4L' indicator
light will blink.