1998 DODGE RAM 1500 Workshop Manual

fuelengine oilAUXair suspensionwiper fluidwindow
Popular search:
Fuel pump Wiringfuel additivesHeated SystemsDiagnosing no startwheel bolt torqueBrake light wiresrocker panel
Previous
Next
Load previous 8 pages

Page 145 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual SPECIAL TOOLS PULLER C-293-PA INSTALLER C-3095-A DIAL INDICATOR SET C-3339 HANDLE C-4171 CUP INSTALLER D-146 DIAL INDICATOR STUD L-4438 SPLITTER 1130 REMOVER/EXTRACTOR 6310 3 - 64 FRONT AXLE - 9 1/4 A

Page 146 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual PINION DEPTH SET 6730 ARBOR DISCS 8289 RECEIVER 8498 PINION BLOCK 8878 ADAPTERS 8879 BEARING INSTALLER 8881 SEAL INSTALLER 8882 DRFRONT AXLE - 9 1/4 AA 3 - 65 FRONT AXLE - 9 1/4 AA (Continued)

Page 147 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual ADJUSTER WRENCH 8883 SEAL INSTALLER 8885 CUP INSTALLER 8886 PLUG 8888 PINION DRIVER 8976 FLANGE WRENCH 8979 3 - 66 FRONT AXLE - 9 1/4 AADR FRONT AXLE - 9 1/4 AA (Continued)

Page 148 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual AXLE SHAFTS REMOVAL (1) With the vehicle in neutral, position vehicle on hoist. (2) Remove brake caliper, rotor and ABS wheel speed sensor if equipped. (3) Remove axle shaft cotter pin, hub nut and wa

Page 149 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (5) Remove hub bearing from the steering knuckle. (6) Remove axle shaft (Fig. 21) from steering knuckle and axle housing. DISASSEMBLY Single cardan U-joint components are not service- able. If defecti

Page 150 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual ASSEMBLY (1) Pack the bearing caps 1/3 full of wheel bearing lubricant. Apply extreme pressure (EP), lithium-base lubricant to aid in installation. (2) Position the spider in the yoke. Insert the seal

Page 151 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (6) Install Extractor Rod 6310 with Extractor Foot 6310-9 through the receiver and the axle seal (Fig. 27). (7) Install Extractor Plate 6310-2 and Nut 6310-7 on the extractor rod. (8) Tighten nut on t

Page 152 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (6) Hold pinion flange with Flange Wrench 8979 (Fig. 31) and remove pinion flange nut and washer. (7) Remove pinion flange with Pinion Flange Puller 8992 (Fig. 32). (8) Remove pinion shaft seal with a
Load next 8 pages
Page:   < prev 1-10 ... 113-120 121-128 129-136 137-144 145-152 153-160 161-168 169-176 177-184 ... 2632 next >
air filterfog lighthood releasewiper sizechange languagebelt
Popular search:
Crankshaft position sensorlow beamcup holderTurn signal indicator diagramtv cablecruise controlkey fob battery