2004 DAEWOO LACETTI Service Repair Manual

change key battery center console jack points tire type power steering fluid MPG

Page 481 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 235
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0445
EVAP PURGE CONTROL CIRCUIT FAULT
Circuit Description
The evaporative emission (EVAP) system includes the fol-
lowing

Page 482 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 236IENGINE CONTROLS
DAEWOO V–121 BL4
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record op

1F – 236IENGINE CONTROLS
DAEWOO V–121 BL4
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Although this DTC is considered a type. A diagnostic, it
acts like a type B diagnostic under certain conditions.
Whenever this diagnostic reports the system has passed,
or if the battery is disconnected, the diagnostic must fail
twice before setting a DTC. The initial failure is not re-ported to the diagnostic executive or displayed on a scan
tool. A passing system always reports to the diagnostic
executive immediately.
Check for the following conditions :
S Missing or damaged fuel cap.
S Missing or damaged O–rings at fuel vapor and
EVAP purge line canister fittings.
S Cracked or punctured EVAP canister.
S Damaged source vacuum line, EVAP purge line,
EVAP vent hose or fuel tank vapor line.
S Poor connection at the ECM. Inspect the harness
connectors for the following conditions.
S Backed–out terminals.
S Improper mating.
S Broken locks.
S Improperly formed.
S Damaged terminals.
S Poor terminal–to–wire connection.
S Damaged harness. Inspect the wiring harness to
the EVAP vent solenoid, EVAP canister purge
valve, and the fuel tank pressure sensor for an in-
termittent open or short circuit.
S Kinked, pinched or plugged vacuum source, EVAP
purge, or fuel tank vapor line. Verify that the lines
are not restricted.
DTC P0445 – EVAP Purge Control Circuit Fault
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Disconnect the evaporative emission (EVAP)
canister purge valve connector.
2. Measure the resistance of the EVAP canister
purge valve connector.
Does the resistance measure near within the value
specified?30WGo to Step 3Go to Step 9
3Connect a test light between EVAP canister purge
valve connector terminal 2 and ground.
Is the test light ON?–Go to Step 4Go to Step 6
41. Disconnect the ECM connector.
2. Connect a test light between the ECM connec-
tor terminal 65 and ground.
Is the test light ON?–Go to Step 5Go to Step 7
51. Repair the high voltage or ground in the wire
between the EVAP canister purge valve con-
nector terminal 2 and the ECM connector ter-
minal 65.
2. Clear any Diagnostic Trouble Codes (DTCs)
from the ECM.
3. Perform the diagnostic system check.
Is the repair complete?–System OK–

Page 483 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 237
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
61. Disconnect the EVAP canister purge valve con-
nector.
2. Connect a test light between the EVAP canister
purge valve conn

Page 484 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 238IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0462
FUEL LEVEL SENSOR LOW VOLTAGE (1.6L DOHC ONLY)
Circuit Description
The engine control module(ECM) uses the fuel level

Page 485 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 239
DAEWOO V–121 BL4
DTC P0462 – Fuel Level Sensor Low Voltage (1.6L DOHC Only)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the s

ENGINE CONTROLS 1F – 239
DAEWOO V–121 BL4
DTC P0462 – Fuel Level Sensor Low Voltage (1.6L DOHC Only)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to ON.
2. Install a scan tool.
3. Operate the vehicle within Freeze Frame con-
ditions as noted.
Is the Diagnostic Trouble Code (DTC) P0462 set?–Go to Step 3Go to
”Diagnostic
Aids”
31. Disconnect the fuel sender electircal connector
from the fuel pump.
2. Using a digital voltmeter (DVM), measure the
voltage in the signal circuit at terminal 1.
Is the voltage within the specified value?0.2–4.8VGo to Step 4Go to Step 6
4Check for a proper ground connection at the fuel
tank and repair as necessary.
Is a repair necessary?–Go to Step 11Go to Step 5
51. Remove the fuel sender from the fuel tank.
2. Reconnect the fuel sender electrical connector.
3. Monitor the Fuel Level Sensor parameter on
the scan tool while moving the Fuel Level Sen-
sor float from the empty position to the full
position.
4. Repeat the procedure several times.
Does the Fuel Level Sensor value on the scan tool
increase and then decrease steadily when the float
is moved?–Go to
”Diagnostic
Aids”Go to Step 8
6Check for an open or short to ground in the Fuel Lev-
el Sensor circuit and repair as necessary.
Is the repair necessary?–Go to Step 11Go to Step 9
7Repair the open or short to ground in the Fuel Level
Sensor circuit between the Fuel Level Sensor har-
ness connector and the Fuel Level Sensor.
Is the repair complete?–Go to Step 11–
8Replace the fuel sender assembly.
Is the replacement complete?–Go to Step 11–
91. Connect the fuel sender electrical connector.
2. Disconnect the engine control module(ECM)
connector.
3. Using a digital voltmeter (DVM) measure the
voltage in the signal circuit, at terminal 46.
Does the DVM read within the specified value?0.2–4.8VGo to Step 10Go to
Section 9E, In-
strumentation/
Driver Informa-
tion
10Replace the ECM.
Is the repair complete?–Go to Step 11–

Page 486 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 240IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
111. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
tempera

Page 487 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 241
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0463
FUEL LEVEL SENSOR HIGH VOLTAGE
(1.6L DOHC ONLY)
Circuit Description
The engine control module(ECM) uses the fuel lev

Page 488 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 242IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0463 – Fuel Level Sensor High Voltage (1.6L DOHC Only)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the s

1F – 242IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0463 – Fuel Level Sensor High Voltage (1.6L DOHC Only)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to ON.
2. Install a scan tool.
3. Operate the vehicle within Freeze Frame con-
ditions as noted.
Is the Diagnostic Trouble Code (DTC) P0463 set?–Go to Step 3Go to
”Diagnostic
Aids”
31. Disconnect the fuel sender electircal connector
from the fuel pump.
2. Using a digital voltmeter (DVM), measure the
voltage in the signal circuit at terminal 1.
Is the voltage within the specified value?0.2–4.8VGo to Step 4Go to Step 6
4Check for a proper ground connection at the fuel
tank and repair as necessary.
Is a repair necessary?–Go to Step 11Go to Step 5
51. Remove the fuel sender from the fuel tank.
2. Reconnect the fuel pump electrical connector.
3. Monitor the Fuel Level Sensor parameter on
the scan tool while moving the Fuel Level Sen-
sor float from the empty position to the full
position.
4. Repeat the procedure several times.
Does the Fuel Level Sensor value on the scan tool
increase and then decrease steadily when the float
is moved?–Go to
”Diagnostic
Aids”Go to Step 8
6Check for an open or short to battery voltage in the
Fuel Level Sensor circuit and repair as necessary.
Is the repair necessary?–Go to Step 11Go to Step 9
7Repair the open or short to battery voltage in the
Fuel Level Sensor circuit between the Fuel Level
Sensor harness connector and the Fuel Level Sen-
sor.
Is the repair complete?–Go to Step 11–
8Replace the fuel sender assembly.
Is the replacement complete?–Go to Step 11–
91. Connect the fuel sender electrical connector.
2. Disconnect the engine control module(ECM)
connector.
3. Using a digital voltmeter (DVM) measure the
voltage in the signal circuit, at terminal 46.
Does the DVM read within the specified value?0.2–4.8VGo to Step 10Go to
Section 9E, In-
strumentation/
Driver Informa-
tion
10Replace the ECM.
Is the repair complete?–Go to Step 11–

Load next 8 pages

Page: < prev 1-10 ... 449-456 457-464 465-472 473-480 481-488 489-496 497-504 505-512 513-520 ... 2648 next >

dashboard brake rotor power steering hood open technical specifications remote control