2004 DAEWOO LACETTI Service Repair Manual

fuel pump auxiliary battery location sensor ESP spark plugs replace traction control

Page 545 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 299
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1382
ROUGH ROAD DATA INVALID (NON ABS)
Circuit Description
The VR sensor is used to detecting the road situation.
By sensi

Page 546 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 300IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performe

1F – 300IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1382.
Does the scan tool indicate that DTC P1382 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. VR sensor seal missing or damaged.
3. VR sensor mounting flanges cracked, missing,
or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the VR sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, terminal 2
and the VR sensor signal circuit, terminal 1 to-
gether at the VR sensor harness connector.
2. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
VR sensor, or for a poor connection at the ter-
minal 53 of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the VR sensor, or a
poor connection at the terminal 84 of the ECM and
repair as needed.
Is the repair complete?–Go to Step 14Go to Step 8
81. Turn the ignition OFF.
2. Disconnect the ECM and check the VR sensor
signal circuit for high resistance, an open, a low
voltage, or a short to the sensor ground circuit
and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9

Page 547 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 301
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
9Check the VR sensor signal circuit for a poor con-
nection at the ECM and repair as needed.
Is the repair complete?–Go to S

Page 548 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 302IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1382
ROUGH ROAD DATA INVALID (ABS)
Circuit Description
The wheel speed sensor is used to detecting the road situ-
ation.
As

Page 549 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 303
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?�

ENGINE CONTROLS 1F – 303
DAEWOO V–121 BL4
DTC P1382 – Rough Road Data Invalid (ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1382.
Does the scan tool indicate that DTC P1382 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. Wheel speed sensor seal missing or damaged.
3. Wheel speed sensor mounting flanges
cracked, missing, or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the defected Wheel speed sensor
electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the Wheel speed sensor value dis-
played on the scan tool.
Is the Wheel speed sensor value near the specified
value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, the Wheel
speed sensor signal circuit, together at the de-
fected Wheel speed sensor harness connector.
2. Observe the defected Wheel speed sensor val-
ue displayed on the scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
Wheel speed sensor, or for a poor connection
of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the Wheel speed
sensor, or a poor connection of the ECM and repair
as needed.
Is the repair complete?–Go to Step 14Go to Step 8

Page 550 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 304IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
81. Turn the ignition OFF.
2. Disconnect the ECM and check the Wheel
speed sensor signal circuit for high resistance,
an open

Page 551 of 2643

DAEWOO LACETTI 2004 Service Repair Manual ENGINE CONTROLS 1F – 305
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1385
ROUGH ROAD SENSOR CIRCUIT FAULT (NON ABS)
Circuit Description
The VR sensor is used to detecting the road situation.

Page 552 of 2643

DAEWOO LACETTI 2004 Service Repair Manual 1F – 306IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1385 – Rough Road Sensor Circuit Fault (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check

1F – 306IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1385 – Rough Road Sensor Circuit Fault (NON ABS)
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition ON, with engine OFF.
2. Install a scan tool to the Data Link Connector
(DLC).
3. Review and record the scan tool Failure Re-
cords data.
4. Operate the vehicle within Failure Records
conditions as noted.
5. Using the scan tool, monitor specific Diagnostic
Trouble Code (DTC) info for DTC P1385.
Does the scan tool indicate that DTC P1385 failed?–Go to Step 4Go to Step 3
31. Check for the following conditions and repair as
needed:
2. VR sensor seal missing or damaged.
3. VR sensor mounting flanges cracked, missing,
or incorrectly installed.
Is the repair complete?–Go to Step 14Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Disconnect the VR sensor electrical connector.
3. Turn the ignition ON, with the engine OFF.
4. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?0VGo to Step 5Go to Step 12
51. Jumper the 5 volt reference circuit, terminal C
and the VR sensor signal circuit, terminal 1 to-
gether at the VR sensor harness connector.
2. Observe the VR sensor value displayed on the
scan tool.
Is the VR sensor value near the specified value?4.95VGo to Step 14Go to Step 10
61. Turn the ignition OFF.
2. Disconnect the Engine Control Module (ECM)
and check the sensor ground circuit for high
resistance, an open between the ECM and the
VR sensor, or for a poor connection at the ter-
minal 53 of the ECM and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 10
7Check the 5 volt reference circuit for high resistance,
an open between the ECM and the VR sensor, or a
poor connection at the terminal 84 of the ECM and
repair as needed.
Is the repair complete?–Go to Step 14Go to Step 8
81. Turn the ignition OFF.
2. Disconnect the ECM and check the VR sensor
signal circuit for high resistance, an open, a low
voltage, or a short to the sensor ground circuit
and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9

Load next 8 pages

Page: < prev 1-10 ... 513-520 521-528 529-536 537-544 545-552 553-560 561-568 569-576 577-584 ... 2648 next >

fuse box diagram headrest warning light reset emergency towing radiator