2001 LAND ROVER FREELANDER Workshop Manual

INTERIOR TRIM COMPONENTS
76-3-4 REPAIRS
Trim casing - rear quarter - upper - 5 door
$% 76.13.13
Remove
1.Remove rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
2.Remove 3 screws securing upper casing to
body.
3.Remove retainer from tail door seal.
4.Release trim casing from 8 retaining clips.
5.Remove upper casing from loadspace.
6.Remove 8 retaining clips from casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit retainer to tail door seal.
4.Fit screws securing bottom of casing.
5.Fit rear quarter lower casing.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-5
Trim finisher - 'A' post - upper - renew
$% 76.13.26
Remove
1.Release seal from door aperture.
2.Release 4 clips and remove 'A' post finisher.
3.Remove clips from finisher.Refit
1.Fit clips to 'A' post finisher.
2.Fit finisher to 'A' post and secure with clips.
3.Fit seal to door aperture.

INTERIOR TRIM COMPONENTS
76-3-6 REPAIRS
Trim finisher - 'B/C' post - upper - renew
$% 76.13.28
Remove
1.Remove seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release finisher from 6 retaining clips and
remove finisher.
NOTE: Do not carry out further dismantling if
component is removed for access only.4.Remove 6 retaining clips from finisher.
5.Remove seat belt slide.
Refit
1.Fit seat belt slide to finisher.
2.Fit retaining clips to finisher.
3.Position finisher and engage retaining clips.
4.Position seat belt lower mounting, fit Torx bolt
and tighten to 40 Nm (29 lbf.ft).
5.Fit seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-7
Trim finisher - 'B' post - lower - 5 door
$% 76.13.29
Remove
1.Remove front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
2.Remove scrivet and 5 Torx screws securing
front carpet retainer and remove carpet
retainer.
3.Release 'B/C' post upper finisher.4.Remove 3 Torx screws from top of seat base
finisher.
5.Remove scrivet and Torx screw from 'B/C' post
lower finisher.
6.Release and remove 'B/C' post lower finisher
from seat base finisher.
Refit
1.Locate 'B/C' post lower finisher under seat base
finisher and rear carpet retainer.
2.Fit scrivet and Torx screw to 'B/C' post lower
finisher.
3.Fit Torx screws to seat base finisher.
4.Align and secure 'B/C' post upper finisher.
5.Fit front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
6.Fit carpet retainer and secure with Torx screws
and scrivet.

INTERIOR TRIM COMPONENTS
76-3-8 REPAIRS
Trim casing - body side - rear - 3 door
$% 76.13.57
Remove
1.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Remove 4 Torx bolts securing trim casing to
body.
4.Release 2 trim clips and trim casing.
5.Disconnect multiplug from tweeter if fitted.
6.Remove trim casing.
Do not carry out further dismantling if
component is removed for access only7.Noting the position of the 3 long screws,
remove 10 Torx screws and remove pocket
from trim casing.
8.Remove 3 screws securing pocket finisher to
trim casing and remove finisher.
9.Release 6 tags and remove speaker grille.
Refit
1.Position speaker grille on replacement casing
and secure tags.
2.Fit pocket finisher and secure with screws.
3.Fit pocket and secure with Torx screws.
4.Fit trim clips to trim casing.
5.Position trim casing and if fitted connect
tweeter multiplug.
6.Fit trim casing to body and secure with clips and
Torx screws.
7.Fit seat belt lower fixing and tighten Torx bolt to
50 Nm (37 lbf.ft).
8.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-9
Console - front - up to 04MY
$% 76.25.01
Remove
1.Remove rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
2.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
3.Remove gear lever knob.
4. Manual gearbox only: Remove descent
selector.
5.Remove 3 heater control knobs.
6.Remove 2 screws from heater control panel.
7.Remove heater control panel.8.Release tags and remove radio cage.
9.Remove 2 screws from top of console.
10.Remove 4 screws securing heater controls to
centre console.
11.Remove 3 screws from centre and sides of
console.
12.Disconnect multiplugs and bulb holder from
switch pack.
13. Automatic gearbox only: Disconnect
multiplugs from gear selector.

INTERIOR TRIM COMPONENTS
76-3-10 REPAIRS
14.Remove centre console.
15.Remove 4 screws from switch pack assembly
and remove assembly.Refit
1.Position switch pack assembly, fit and tighten
screws.
2.Position console to fascia.
3.Connect multiplugs and bulb holder to switch
pack.
4. Automatic gearbox only: Connect multiplugs
to gear selector.
5.Fit centre console.
6.Fit and tighten screws securing centre and
sides to console.
7.Fit and tighten screws securing switch pack to
console.
8.Fit and tighten screws to top of console.
9.Position radio cage to console and secure with
retaining tags.
10.Position heater control panel, fit and tighten
screws.
11.Fit heater control knobs.
12. Manual gearbox only: Fit descent selector.
13.Fit gear lever knob.
14.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
15.Fit rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-11
Console assembly - front - from 04MY
$% 76.25.01
Remove
1.Remove rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
2.Remove gear selector indicator assembly.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Selector indicator - from 04MY.
3.Carefully lever upper console finisher rearward,
to release clips on forward edge of finisher.
4.Remove 4 screws securing centre console.5.Disconnect 6 multiplugs and remove console.
NOTE: Do not carry out further dismantling if
component is removed for access only.
6.Remove switches from console, noting fitted
position.
7.Remove 4 screws securing ash tray to centre
console finisher and remove ash tray.
Refit
1.Fit switches to console.
2.Fit and secure ash tray to centre console
finisher.
3.Position console assembly and connect
multiplugs.
4.Fit console and secure with screws.
5.Align upper console finisher and secure with
clips.
6.Refit gearshift selector assembly.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Selector indicator - from 04MY.
7.Fit rear console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - rear.
M76 4695