2001 LAND ROVER FREELANDER Workshop Manual

EXTERIOR FITTINGS
76-2-8 REPAIRS
Cable/rod - bonnet lock control
$% 76.16.29
Remove
1.Remove bonnet lock.
2.Tie a draw string to end of bonnet release cable
and pull cable from bonnet locking platform.
3.Untie draw string from bonnet release cable.
4.Remove 3 cable ties and release bonnet
release cable from harness.5.Remove bolt securing bonnet release lever to
'A' post lower panel.
6.Remove bonnet release cable from lever and
remove lever.
7.Pull sound insulation away from bulkhead for
access to bonnet release cable grommet.
8.Remove grommet from engine bulkhead.
9.Remove bonnet release cable.

EXTERIOR FITTINGS
REPAIRS 76-2-9
Refit
1.Fit bonnet release cable through bulkhead.
2.Position bonnet release lever and connect
bonnet release cable to lever.
3.Fit release lever to 'A' post and tighten bolt to 9
Nm (7 lbf.ft).
4.Fit bonnet release cable grommet to bulkhead.
5.Position bonnet release cable to main harness
and secure with cable ties.
6.Fit sound insulation to bulkhead.
7.Tie draw string to end of bonnet release cable.
8.Pull draw string to fit bonnet release cable
through bonnet locking platform.
9.Untie draw string from bonnet release cable.
10.Fit bonnet lock.
11.Close bonnet and check for correct locking
operation.

EXTERIOR FITTINGS
76-2-10 REPAIRS
Bumper - assembly - front - up to 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheelarch for
access.
3.Remove 2 screws securing bumper valance to
underbelly panel brackets.
4.Remove 3 scrivets securing bumper to
armature.
5.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
6.Remove 4 screws securing bumper to bonnet
locking platform.
7. NAS Models: Release side repeater,
disconnect multiplug and remove repeater.
8.With assistance carefully lift and pull forward
each side of bumper to release bumper side
mounts and clips.
CAUTION: Always protect paintwork when
removing or refitting any body trims or
bumpers.
9.Remove front number plate.
10.Remove badge from grill and discard clips.Refit
1.Fit badge to grill.
2.Fit number plate.
3.With assistance, fit bumper assembly to body.
4. NAS Models: Feed side repeater harness
through bumper, connect multiplug and fit
repeater.
5.Ensure bumper locating pegs are correctly
aligned.
6.Fit and tighten bolts securing bumper to wings.
7.Fit screws securing bumper to bonnet locking
platform.
8.Fit scrivets to armature.
9.Fit screws securing bumper to underbelly
panel.
10.Fit and align wheelarch liners and tighten
screws.
11.Close bonnet.

EXTERIOR FITTINGS
REPAIRS 76-2-11
Bumper - assembly - front - from 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheel arch for
access.
3.Remove 4 screws securing bumper valance to
underbelly panel.
4.Remove 3 scrivets securing bumper to
armature.5.Disconnect multiplugs from fog/driving lamps.
6.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
7.Remove 4 screws securing bumper to bonnet
locking platform.
M76 4674

EXTERIOR FITTINGS
76-2-12 REPAIRS
8.With assistance, carefully pull each side of
bumper forward to release it from its
mountings.
CAUTION: Always protect paintwork when
removing or refitting any body trims or
bumpers.
9.Remove front bumper.
NOTE: Do not carry out further dismantling if
component is removed for access only.
10.Remove front number plate.
11.Remove clips securing badge to grille, remove
badge and discard clips.12.Release and remove fog/driving lamp finisher
from bumper.
13.Remove 6 screws securing fog/driving lamps to
bumper.
14.Remove 6 speed nuts from bumper.
Refit
1.Fit 6 speed nuts to bumper.
2.Fit fog/driving lamps to bumper and secure with
screws.
3.Fit fog/driving lamp finishers to bumper.
4.Fit badge to grille.
5.Fit number plate.
6.With assistance, fit bumper assembly to body.
7.Ensure bumper locating pegs are correctly
aligned.
8.Fit and tighten bolts securing bumper to wings.
9.Connect multiplugs to fog/driving lamps.
10.Fit screws securing bumper to bonnet locking
platform.
11.Fit scrivets to armature.
12.Fit screws securing bumper to underbelly
panel.
13.Fit and align wheel arch liners and tighten
screws.
14.Close bonnet.
M76 4677
M76 4679

EXTERIOR FITTINGS
REPAIRS 76-2-13
Bumper valance - rear - up to 04MY
$% 76.22.74
Remove
1.Remove rear mud flaps.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - rear.
2.Remove both rear tail lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
3.Remove rear wheel arch extensions.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
4.Remove 10 screws securing bumper valance to
body.
5.Remove 2 nuts and bolts securing bumper
valance to armature.
6.Remove 5 scrivets securing bumper valance to
body.
7.Remove 2 mud flap brackets.
8. NAS Models: Release side repeater,
disconnect multiplug and remove repeater.
9.With assistance remove bumper valance.
Refit
1.With assistance fit bumper valance and secure
with scrivets, screws, nuts and bolts.
2. NAS Models: Feed side repeater harness
through bumper, connect multiplug and fit
repeater.
3.Fit mud flap brackets and secure with screws.
4.Fit rear wheel arch extensions.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
5.Fit both rear tail lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
6.Fit rear mud flaps.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - rear.
Bumper valance - rear - from 04MY
$% 76.22.74
Remove
1.Remove rear mud flaps.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - rear.
2.Remove both rear fog lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - rear.
3.Remove rear wheel arch extensions.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
4.Remove 2 screws and remove both mud flap
retaining brackets.
5.Remove 6 Torx screws securing luggage
compartment carpet retainer to body.
6.Remove luggage compartment carpet retainer.

EXTERIOR FITTINGS
76-2-14 REPAIRS
7.Release tailgate aperture seal to access
bumper valance to body retaining scrivets.
8.Remove 5 scrivets securing bumper valance to
body.
9.Remove 4 screws securing bumper valance to
body.
10.Remove 2 Torx bolts securing bumper valance
to bumper armature.11.With assistance, release bumper valance and
parking aid sensor harness from body.
12.Remove parking aid sensor harness retaining
clip and disconnect multiplug.
13.Remove bumper valance.
NOTE: Do not carry out further dismantling if
component is removed for access only.
14.Remove both rear tail lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
15.Disconnect multiplugs from 4 parking aid
sensors and release harness from 9 retaining
clips.
16.Remove parking aid harness from bumper
valance.
M76 4682

EXTERIOR FITTINGS
REPAIRS 76-2-15
17.Release 2 retaining clips and remove parking
aid sensor from finisher.
18.Remove parking aid sensor finisher from
bumper valance.
19.Repeat above procedure for remaining 3
parking aid sensors.
20.Remove tail lamp speed nuts from bumper
valance.Refit
1.Fit tail lamp speed nuts to bumper valance.
2.Fit and secure parking aid finishers and
sensors to bumper valance.
3.Fit and secure parking aid harness to sensors
and bumpers valance.
4.Fit both rear tail lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
5.With assistance, position bumper valance to
body.
6.Connect parking aid harness multiplug, fit
retaining clip and secure to body.
7.Align bumper valance to body and secure with
retaining screws and scrivets.
8.Fit Torx screws securing bumper valance to
bumper armature and tighten to 5 Nm (3.7
lbf.ft).
9.Fit tailgate aperture seal to body.
10.Fit luggage compartment carpet retainer and
secure with Torx screws.
11.Fit both mud flap retaining brackets and secure
with screws.
12.Fit rear wheel arch extensions.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
13.Fit both rear fog lamps.

+ LIGHTING, REPAIRS, Lamp
assembly - rear.
14.Fit rear mud flaps.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - rear.