2001 LAND ROVER FREELANDER Workshop Manual

EXTERIOR FITTINGS
76-2-16 REPAIRS
Finisher - sill - lower
$% 76.43.28
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove both jacking point covers.
3.Remove 7 scrivets securing sill finisher to body.
4.Release and remove finisher from sill.Refit
1.Clean mating faces of finisher.
2.Position finisher to sill, locate over jacking
points and secure with scrivets.
3.Fit jacking point covers.
4.Remove stands and lower vehicle.

EXTERIOR FITTINGS
REPAIRS 76-2-17
Moulding - roof - 5 door
$% 76.43.68
Remove
1.Remove tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
2.Remove roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
3.Using a suitable hooked tool in the front foot
hole of the roof finisher, slide the finishers 2
forward clips rearward from the roof channel.
4.Slide the clip rear of the foot hole forward from
the roof channel.
5.Slide the remaining 7 clips from the roof
channel.
6.Remove nut securing rear end of roof finisher
and remove finisher.
7.Remove clips from roof finisher.Refit
1.Fit clips to roof finisher.
2.Fit finisher to roof channel with forward 2 clips.
3.Slide finisher to align with screen. Feed forward
clip below screen seal.
4.Fit remaining clips to roof channel.
5.Fit nut and secure rear end of finisher.
6.Ensure full length of finisher is correctly seated
in roof channel.
7.Fit roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
8.Fit tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.

EXTERIOR FITTINGS
76-2-18 REPAIRS
Wheelarch extension - rear wing part
$% 76.43.94
Remove
1.Raise rear of vehicle.
2.Remove road wheel(s).
3. 5 door models:Remove 2 scrivets securing
extension to edge of wheel arch.
4. 5 door models: Remove wheel arch extension
from 2 fixing studs.
5. 5 door models: Remove fasteners from arch
extension.6. 3 door models: Remove 6 scrivets securing
extension to edge of wheel arch and sill panel.
7. 3 door models: Remove wheel arch extension
from 8 fixing studs.
8. 3 door models: Remove fasteners from arch
extension.
Refit
1.Fit fasteners to wheel arch extension.
2.Fit wheel arch extension to studs.
3.Fit scrivets securing extension to wheel arch.
4.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
5.Remove stands and lower vehicle.

EXTERIOR FITTINGS
REPAIRS 76-2-19
Body quarter vent assembly - 3 door
$% 76.81.24
Remove
1.Remove 2 Torx screws securing vent hinge
covers.
2.Remove covers from hinges.
3.Remove 2 screws securing hinges to vent.
4.Remove hinges from vent.
5.Remove nuts from vent and discard sealing
washers.
6.With assistance remove screw securing vent
catch to body.
7.Remove vent.8.Remove screw securing catch to vent.
9.Remove catch from vent.
10.Remove nut from vent and discard sealing
washers.
Refit
1.Fit nut and new sealing washer to vent.
2.Fit catch and tighten screw.
3.With assistance fit vent and tighten catch
screw.
4.Using new sealing washers fit nuts and hinges
to vent. Fit and tighten hinge screws to vent.
5.Fit hinge covers and tighten Torx screws.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-1
INTERIOR TRIM COMPONENTS REPAIRS
Sun visor
$% 76.10.47
Remove
1.Release sun visor from retaining clip.
2.Remove 2 screws securing sun visor to roof.
3.Disconnect multiplug from sun visor.
4.Remove sun visor.
5.Remove screw securing sun visor clip to roof
and remove clip.
Refit
1.Fit sun visor clip to roof and secure with screw.
2.Fit sun visor to roof and secure with screws.
3.Fit sun visor to clip.
4.Position sun visor and connect multiplug.
Trim casing - rear quarter - lower - 3 door
$% 76.13.12
Remove
1. 03MYRemove body side rear trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
2.Release rear seat squab and fold seat forward.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 6 Torx screws securing luggage
compartment carpet retainer.
6.Remove carpet retainer.
7.Release 4 turn buckles securing trim casing.
8.Release and remove trim casing from luggage
compartment.
Refit
1.Fit trim casing to luggage compartment and
secure with turn buckles.
2.Fit luggage compartment carpet retainer and
secure with Torx screws.
3.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
4.Reposition rear seat.

INTERIOR TRIM COMPONENTS
76-3-2 REPAIRS
Trim casing - rear quarter - lower - 5 door
$% 76.13.12
Remove
1.Release rear seat squab and fold seat forward.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 2 screws securing casing to load
space carpet retainer.
6.Release 4 turn buckles securing trim casing.
7.Release trim casing from 5 retaining clips.
8.Remove loadspace side trim casing.
9.Remove 5 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit turn buckles.
4.Fit screws securing casing to carpet retainer.
5.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
6.Position loadspace cover retainer and secure
with screw.
7.Fit loadspace cover and secure in retainers.
8.Position rear seat belt and tighten bolt to 40 Nm
(29 lbf.ft).
9.Reposition rear seats.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-3
Trim casing - rear quarter - upper - 3 door
$% 76.13.13
Remove
1.Remove rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.
2.Remove body rear side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
3.Remove screw and release rear vent catch.
4.Remove seat belt access cover from upper
casing.
5.Release 4 clips securing upper casing to body
and remove casing.
6.Remove 4 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position trim casing, align seat belt and secure
casing retaining clips.
3.Fit seat belt access cover.
4.Position rear vent sealing rubber to trim casing.
5.Position rear vent catch and tighten screw.
6.Fit body rear side trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
7.Fit rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.