2001 LAND ROVER FREELANDER Workshop Manual

ENGINE - K SERIES KV6
12-3-112 OVERHAUL
35.Position tools LRT-12-196 to LH and RH front
inlet camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
36.Remove and discard bolts retaining front inlet
camshaft gears to camshafts.
37.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.
38.Remove camshaft drive gears and hub
assemblies.
Refit
NOTE: Following front or rear timing belt
refitment, it is possible that, after rotating the
engine and positioning the crankshaft pulley to
the 'SAFE' position, the timing marks on the
rear timing gears may be misaligned. This
misalignment is acceptable provided that the
timing belt refitting procedure was carried out
correctly.
1.Clean camshaft gears and hubs, crankshaft
gear, tensioner and water pump pulleys.
CAUTION: If sintered gears have been
subjected to prolonged oil contamination,
they must be soaked in solvent and then
thoroughly washed in clean solvent before
refitting. Because of the porous
construction of sintered material, oil
impregnated in the gears will emerge and
contaminate the timing belts.
2.Fit hubs to camshaft gears and fit gears to
camshafts.
3.Fit new camshaft gear bolts; tighten bolts
sufficiently to allow gears to rotate without
tipping.4.Position timing belt to crankshaft gear.
NOTE: To prevent the timing belt from
disengaging from the crankshaft gear when
fitting, fit a suitable wedge between the belt and
oil pump belt guard.
5.Fit tool LRT-12-197 into each exhaust
camshaft in turn.
6.Using assistance, rotate each exhaust
camshaft slightly and align timing marks on LH
and RH rear camshaft gears.
7.Remove tool LRT-12-197.
8.Fit tools LRT-12-175 to LH and RH rear
camshaft gears.
9.Rotate both front camshaft gears fully
clockwise as viewed from front of engine.
10.Using fingers only, fit timing belt to gears,
starting at the crankshaft gear and working in
an anti-clockwise direction, keeping the belt run
as taut as possible and turning the camshaft
gears only a minimum amount anti-clockwise to
fit timing belt.
CAUTION: Gears must not be rotated anti-
clockwise more than one tooth.

ENGINE - K SERIES KV6
OVERHAUL 12-3-113
11.Position an Allen key in tensioner backplate
and hold tensioner pulley against timing belt.
12.With assistance, position timing belt tensioner,
fit new Patchlok bolts and tighten to 25 Nm (18
lbf.ft).
CAUTION: Ensure tensioner plunger is
contacting underside of tensioner
backplate.
13.Remove tools LRT-12-175 from rear timing belt
gears.
14.Fit tools LRT-12-196 to both front inlet
camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
15.Tighten front inlet camshaft gear bolts to:
lStage 1 - 27 Nm (20 lbf.ft)
lStage 2 - Further 90°
16.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.17.Remove wedge from between drive belt and oil
pump belt guard.
18.Remove 1.5 mm diameter pin from tensioner.
19.Clean exhaust camshaft front cap seal
locations and fit new cap seals.
CAUTION: The sealing edge of the cap seal
and mating face must be clean and dry.
20.Position engine front mounting plate and
manoeuvre plate into position; fit bolts but do
not tighten at this stage.
21.Fit bolts securing IRD support bracket to front
mounting plate; do not tighten bolts at this
stage.
22.Tighten bolts in the sequence shown:
lM10 bolt - No.1 - 25 Nm (18 lbf.ft)
lM10 bolt - No. 5 - 45 Nm (33 lbf.ft)
lBolts Nos. 2, 3, 4, 6 and 7 - 85 Nm (63 lbf.ft)
23.Position engine lifting bracket, fit bolts securing
lifting bracket and front mounting plate to
cylinder block and RH cylinder head and
tighten to:
lM8 bolt - 25 Nm (18 lbf.ft)
lM10 bolts - 45 Nm (33 lbf.ft)
24.Fit rubber blanking plug around tensioner.
25.Clean end of dipstick tube.
26.Position dipstick tube to sump and cylinder
block, fit bolt and tighten to 9 Nm (7 lbf.ft).
27.Clean lower timing belt cover.
28.Position lower timing belt cover, fit and tighten
bolts to 9 Nm (7 lbf.ft).
29.Remove timing pin LRT-12-232.
30.Clean crankshaft pulley.
31.Fit crankshaft pulley to crankshaft gear and
ensure that the indent on pulley locates over
the lug on crankshaft gear.
32.Fit crankshaft pulley bolt and washer, position
LRT-12-161 with LRT-12-199 into crankshaft
pulley. Tighten pulley bolt to 160 Nm (118
lbf.ft).
33.Remove tools LRT-12-161 and LRT-12-199.
34.Clean ancillary drive belt tensioner.

ENGINE - K SERIES KV6
12-3-114 OVERHAUL
35.Position ancillary belt tensioner, fit bolts and
tighten to 25 Nm (18 lbf.ft).
36.Clean LH and RH front timing belt covers.
37.Position LH and RH front timing belt covers, fit
and tighten bolts to 4 Nm (3 lbf.ft).
38.Clean idler pulley, position pulley to engine
front mounting plate and tighten Torx bolt to 45
Nm (33 lbf.ft).
39.Position alternator to front mounting plate.
40.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
41.Connect alternator multiplug.
42.Connect battery lead to alternator, fit and
tighten nut to 8 Nm (6 lbf.ft), fit terminal cover.
43.Clean LH rear timing belt cover.
44.Position LH rear timing belt cover, fit and
tighten bolts to 4 Nm (3 lbf.ft).
45.Clean RH rear timing belt cover.
46.Position RH rear timing belt cover, fit bolts and
tighten to 4 Nm (3 lbf.ft).
47.Position heat shield, fit bolts and tighten M6 bolt
to 9 Nm (7 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
48.Fit inlet manifold chamber - if fitted.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
49.Position ancillary drive belt to crankshaft and
alternator pulleys.
50.Position engine mounting front bracket to
engine front plate and tighten bolts to 45 Nm
(33 lbf.ft).

EMISSION CONTROL
ADJUSTMENTS 17-1-1
EMISS ION CONTROL ADJUST ME NTS
Evaporative loss control system
(EVAPS) - leak test - NAS
$% 17.90.02.01
The following procedure allows a fuel leak, indicated
by the Malfunction Indicator Lamp (MIL), to be
accurately located. It must only be carried out once it
has been established that there are no obvious faults
with any of the system components.
Check
1.Check components in fuel and EVAP system
for obvious damage. Ensure all connections
are properly secured.
2.The system must be checked using a EVAPS
Diagnostic Testing Station LRA-19-004.
3.Disconnect vent pipe from purge valve and
connect adapter LRA-19-004/1.
NOTE: The reason for inserting the adapter into
the purge valve is that there is currently no
service port fitted to Freelander.
4.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
5.Release clip and disconnect hose from
charcoal canister.
CAUTION: Before disconnecting any part of
the fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign
matter into fuel system.
6.Block charcoal canister port with bung,
included in LRA-19-004.
7.Connect LRA-19-004 to service port fitted on
purge valve.
8.Carry out procedures given in the operating
instructions, these are supplied with LRA-19-
004.Adjust
1.If a leak has been detected, replace component
as necessary and repeat leak test to validate
repair.
2.Remove bung from charcoal canister.
3.Connect hose to charcoal canister and secure
with clip.
4.Fit rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
5.Disconnect adaptor LRA-19-004/1 from purge
valve.
6.Connect hose to purge valve.

EMISSION CONTROL
REPAIRS 17-1-3
REPAIRS
Valve - depression limiter - Td4
$% 17.10.25
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner element

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
3.Disconnect multiplugs from injectors.
4.Remove 3 screws and move injector harness
aside.
5.Remove 4 Allen screws and remove valve with
filter assembly. Discard seals.Refit
1.Clean filter with valve housing and mating
faces.
2.Use new seals, fit filter and valve assembly,
tighten Allen screws to 8 Nm (6 lbf.ft).
3.Position injector harness and secure with
screws.
4.Connect multiplugs to injectors.
5.Fit air cleaner element.
+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
6.Connect battery earth lead.
M17 0280
M17 0281

EMISSION CONTROL
17-1-4 REPAIRS
Solenoid - canister purge - KV6
$% 17.15.06
Remove
1.Disconnect battery earth lead.
2.Disconnect multiplug from purge control valve.
3.Disconnect hose from purge control valve.
4.Remove screw and plain washer securing
purge control valve to manifold chamber.
5.Remove purge control valve, remove and
discard seal.
Refit
1.Clean purge control valve and mating face on
manifold chamber.
2.Fit new seal to purge control valve.
3.Position purge control valve to manifold
chamber, secure with plain washer and screw.
4.Connect multiplug and secure hose to purge
control valve.
5.Connect battery earth lead.
Charcoal canister - petrol - Non NAS
$% 17.15.13
Remove
1.Raise rear of vehicle, one side.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove nut securing charcoal canister to
bracket.
3.Remove charcoal canister from bracket.
4.Disconnect tank, air and purge pipes from
charcoal canister.
CAUTION: Always fit plugs to open
connections to prevent contamination.
5.Remove charcoal canister.
Refit
1.Connect tank, air and purge pipes to charcoal
canister.
2.Fit charcoal canister to bracket and secure with
nut.
3.Lower vehicle.

EMISSION CONTROL
REPAIRS 17-1-5
Charcoal canister - NAS
$% 17.15.13
Remove
1.Disconnect battery earth lead.
2.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
3.Release and disconnect pipes from charcoal
canister and DMTL.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
4.Remove 2 bolts securing canister support
bracket and release assembly from mounting.
5.Disconnect multiplug from DMTL and remove
canister and valve assembly.6.Release clip and disconnect hose from
charcoal canister.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
7.Remove nut and bolt securing charcoal
canister and remove canister from bracket.
Refit
1.Fit charcoal canister to bracket and tighten nut
and bolt to 4 Nm (3 lbf.ft).
2.Connect hose and secure with clip.
3.Position canister assembly and connect
multiplug.
4.Fit canister assembly to mounting and tighten
bolts to 4 Nm (3 lbf.ft).
5.Connect pipes to DMTL and canister.
6.Fit wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
7.Connect battery earth lead.