ENGINE - K SERIES KV6
REPAIRS 12-3-19
10.Tighten cylinder head bolts progressively in the
sequence illustrated to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit RH camshaft cover gasket.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
12.Remove and discard lower 'O' rings from
injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail; secure injector harness to protection
cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hoses to RH camshaft cover
and inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Connect multiplugs to plug top coils and secure
with locking clips.
23.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
24.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).25.Fit camshaft timing belt.
+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
26.Fit RH exhaust manifold gasket.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - RH - Non NAS.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - RH - KV6 - NAS.
27.Fit inlet manifold chamber.
+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
28.Fill cooling system.
+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
29.Check engine oil level and top-up if necessary.
+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
FUEL DELIVERY SYSTEM - PETROL
19-2-28 REPAIRS
Filter - main
$% 19.25.02
Remove
1.Disconnect battery earth lead.
2.Remove sender unit.
+ INSTRUMENTS, REPAIRS, Sender
unit - fuel tank gauge.
3.Disconnect 2 Lucars from top of pump unit
assembly.
4.Release 3 slots in top of pump unit assembly
from lugs in base.
5.Carefully manoeuvre top of pump unit
assembly away from base, ensuring that fuel
feed hose does not become strained.
6.Collect compression spring from fuel filter.
7.Carefully release 3 sprag clips securing fuel
filter.8.Release fuel filter from inlet and outlet
connections.
9.Remove fuel filter.
10.Collect 'O' rings.
Refit
1.Lubricate NEW 'O' rings with silicone grease
and fit to ports.
2.Carefully fit fuel filter to ports and push fully
home, ensuring that sprag clips engage fully.
WARNING: Ensure earthing spring fitted to
fuel pressure regulator is correctly located.
3.Position spring to fuel filter recess and engage
in top location.
WARNING: Ensure that filter earthing tag is
correctly located to contact the base of fuel
filter.
4.Engage pump top to base, ensuring that slots
engage correctly with lugs.
WARNING: During refit, ensure that all
electrical connections are made correctly.
Earth tag on fuel pump negative terminal
must not become distorted.
5.Fit sender unit.
+ INSTRUMENTS, REPAIRS, Sender
unit - fuel tank gauge.
6.Connect battery earth lead.
