2001 LAND ROVER FREELANDER alternator

CONTENTS
CONTENTS 19
WIPERS AND WASHERS ........................................................................ 84-1
REPAIRS
Reservoir - washer ......................................................................................................................... 84-1
Jet - washer - each ........................................................................................................................ 84-2
Pump - washer ............................................................................................................................... 84-2
Arm - wiper - each .......................................................................................................................... 84-3
Blade - wiper - each ....................................................................................................................... 84-3
Motor & linkage - wiper .................................................................................................................. 84-4
Switch - wiper/washer .................................................................................................................... 84-4
Pump - washer ............................................................................................................................... 84-5
Arm - wiper ..................................................................................................................................... 84-5
Blade - wiper .................................................................................................................................. 84-6
Motor - wiper .................................................................................................................................. 84-7
Switch - combined wiper/washer ................................................................................................... 84-8
Relay - tailgate wipe - 5 door ......................................................................................................... 84-8
CHARGING AND STARTING ................................................................... 86-1-1
ADJUSTMENTS
Ancillary drive belt - K1.8 ............................................................................................................... 86-1-1
Ancillary drive belt - K1.8 with A/C .................................................................................................. 86-1-2
REPAIRS
Alternator - Td4 ............................................................................................................................... 86-1-3
Alternator - KV6 .............................................................................................................................. 86-1-5
Alternator - K1.8 .............................................................................................................................. 86-1-6
Ancillary drive belt - Td4 ................................................................................................................. 86-1-7
Ancillary drive belt - K1.8 without A/C ............................................................................................. 86-1-8
Ancillary drive belt - K1.8 with A/C .................................................................................................. 86-1-9
Ancillary drive belt - KV6 ................................................................................................................. 86-1-10
Tensioner - ancillary drive belt - Td4 ............................................................................................... 86-1-11
Battery ............................................................................................................................................. 86-1-12
Carrier - battery ............................................................................................................................... 86-1-13
Relay - main .................................................................................................................................... 86-1-14
Starter motor - Td4 .......................................................................................................................... 86-1-15
Starter motor - KV6 ......................................................................................................................... 86-1-16
Starter motor - K1.8 ........................................................................................................................ 86-1-17
Relay - starter ................................................................................................................................. 86-1-18

GENERAL DATA
04-34
Electrical - Td4 engine
Electrical - K1.8 engine
Electrical - KV6 engine
System 12 volt, negative earth
Battery:
⇒ Type
⇒ CapacityH6, sealed for life
75 amp /hour
⇒ Type
⇒ CapacityH7, sealed for life (cold climates)
80 amp /hour
Alternator:
⇒ Type
⇒ Maximum output
⇒ Maximum output (models with PTC heater)Nippon Denso K-frame
105 amp
150 amp
System 12 volt, negative earth
Battery:
⇒ Type
⇒ CapacityH5, sealed for life
55 amp/hour
Alternator
⇒ Type
⇒ Maximum outputNippon Denso K-frame
105 amp
System 12 volt, negative earth
Battery:
⇒ Type
⇒ CapacityH6, sealed for life
75 amp/hour
Alternator:
⇒ Type
⇒ Maximum outputNippon Denso L-frame
120 amp

TORQUE WRENCH SETTINGS
06-16
Manifolds and Exhaust Systems – K1.8
†Tighten in sequence.
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator bolts45 Nm 33 lbf.ft
Alternator mounting bracket bolts 25 Nm 18 lbf.ft
Coil cover bolts10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold bolts 10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold nut 25 Nm 18 lbf.ft
Exhaust front pipe to intermediate pipe nuts 60 Nm 44 lbf.ft
Exhaust front pipe to manifold nuts 60 Nm 44 lbf.ft
Exhaust manifold to cylinder head nuts
†45 Nm 33 lbf.ft
Exhaust manifold heatshield to front pipe bolts 9 Nm 7 lbf.ft
Heated Oxygen (HO
2S) Sensor 55 Nm 41 lbf.ft
Heatshield to alternator bracket:
⇒ Nut25 Nm 18 lbf.ft
⇒ Bolts10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts
†17 Nm 12.5 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
RH coil bolts10 Nm 7.5 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-35
Electrical
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator drive belt tensioner bolt 25 Nm 18 lbf.ft
Alternator mounting bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to front mounting plate nut and bolts (KV6) 45 Nm 33 lbf.ft
Alternator support bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to mounting bracket bolts (Td4):
⇒ M825 Nm 18 lbf.ft
⇒ M1045 Nm 9.5 lbf.ft
Alternator upper and lower bolts (K1.8 with A/C) 45 Nm 33 lbf.ft
Ancillary drive belt idler pulley to mounting Allen bolt (Td4) 25 Nm 18 lbf.ft
Battery cable to alternator terminal nut (Td4 & KV6) 10 Nm 7.5 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 8 Nm 6 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 13 Nm 9.5 lbf.ft
Battery clamp bolt 12 Nm 9 lbf.ft
Battery and starter motor lead to underbonnet fusebox bolts 8 Nm 6 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Passenger compartment fusebox mounting plate to body bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Starter motor mounting bolts (Td4) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 80 Nm 59 lbf.ft

MAINTENANCE
10-22 MAINTENANCE
Engine Oil and Filter – Td4
Drain
1.Raise vehicle on ramp.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Place a suitable container under engine sump
drain plug, remove drain plug and discard
sealing washer. Allow oil to drain.
WARNING: Observe due care when draining
engine oil as the oil can be very hot.
WARNING: Avoid excessive skin contact
with used engine oil. Used engine oil
contains potentially harmful contaminants
which may cause skin cancer or other
serious skin disorders.
4.Lower vehicle
5.Remove oil filter cap and discard 3 seals.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.Refill
1.Replace engine oil filter.

+ ENGINE - Td4, REPAIRS, Filter -
engine oil.
2.Fit new seals and lubricate with clean engine
oil.
3.Fit oil filter cap and tighten to 25 Nm (18 lbf.ft).
4.Raise vehicle.
5.Clean sump drain plug, fit new sealing washer
and tighten sump drain plug to 28 Nm (21 lbf.ft).
6.Fit oil filler cap.
7.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
8.Lower vehicle.
9.Remove engine oil filler cap and fill engine with
oil to correct level.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
10.Start engine. Run at idle until oil pressure
warning light extinguishes.
11.Stop engine. Recheck engine oil level.
12.Check for signs of leakage.

ENGINE - K SERIES KV6
REPAIRS 12-3-59
10.Insert timing pin LRT-12-232 through hole in
lower crankcase, ensuring pin is located in hole
in drive plate.
CAUTION: Hole immediately adjacent to
side of lower crankcase must be used.
11.Remove bolt securing PAS pipe to engine front
mounting plate.12.Remove 3 Torx screws securing PAS pump
pulley and remove pulley.
13.Remove 3 bolts securing PAS pump to front
mounting plate and tie pump aside.
14.Release alternator battery lead terminal cover,
loosen terminal nut and disconnect lead from
terminal.
15.Disconnect multiplug from alternator.
LRT-12-232
M12 7927

ENGINE - K SERIES KV6
12-3-60 REPAIRS
16.Remove lower bolt and upper nut and bolt
securing alternator to front mounting plate.
17.Remove alternator.
18.Remove Torx screw securing idler pulley to
front mounting plate and remove pulley.
19.Loosen bolt securing lower engine steady to
front subframe.
20.Remove bolt securing lower engine steady to
sump mounting, release lower engine steady
from sump mounting.21.Remove 3 bolts securing camshaft timing belt
RH front cover and remove cover.
22.Remove 3 bolts securing camshaft timing belt
LH front cover and remove cover.
23.Assemble LRT-12-161 to LRT-12-199 and
secure with clamp bolt.
M12 6597

ENGINE - K SERIES KV6
REPAIRS 12-3-65
11.With assistance, position tensioner, fit new
Patchlok bolts and tighten to 25 Nm (18 lbf.ft).
CAUTION: Ensure tensioner plunger is
contacting underside of tensioner
backplate.
12.Remove tools LRT-12-175 from rear timing belt
gears.
13.Fit tools LRT-12-196 to both front inlet
camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
14. Tighten front inlet camshaft gear bolts to:
lStage 1 - 27 Nm (20 lbf.ft)
lStage 2 - Further 90°
15.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.
16.Remove wedge from between drive belt and oil
pump belt guard.
17.Remove 1.5 mm diameter pin from tensioner.
18.Fit rubber blanking plug around tensioner.
19.Remove timing pin LRT-12-232.
20.Clean exhaust camshaft front cap seal
locations and fit new cap seals.
CAUTION: The sealing edge of the cap seal
and mating face must be clean and dry.
21.Position engine front mounting plate and
manoeuvre plate into position. Fit bolts but do
not tighten at this stage.22.Fit bolts securing IRD support bracket to front
mounting plate but do not tighten at this stage.
23.Tighten bolts in the sequence shown:
lBolt No. 1 - 25 Nm (18 lbf.ft)
lBolt No. 5 - 45 Nm (33 lbf.ft)
lBolts Nos. 2, 3, 4, 6 and 7 - 85 Nm (63 lbf.ft)
24.Position engine lifting bracket, fit bolts securing
lifting bracket and front mounting plate to
cylinder block and RH cylinder head. Tighten
M10 bolts to 45 Nm (33 lbf.ft) and M8 bolt to 25
Nm (18 lbf.ft).
25.Clean end of dipstick tube.
26.Position dipstick tube to sump and cylinder
block, fit bolt and tighten to 9 Nm (7 lbf.ft).
27.Position A/C compressor to front mounting
plate and cylinder block, align heat shield, fit
and tighten bolts to 25 Nm (18 lbf.ft).
28.Clean lower timing belt cover.
29.Position lower timing belt cover, fit and tighten
bolts to 9 Nm (7 lbf.ft).
30.Clean crankshaft pulley.
31.Fit crankshaft pulley to crankshaft gear and
ensure that the indent on pulley locates over
the lug on crankshaft gear.
32.Fit crankshaft pulley bolt and washer, position
LRT-12-161 with LRT-12-199 into crankshaft
pulley. Tighten pulley bolt to 160 Nm (118
lbf.ft).
33.Remove tools LRT-12-161 and LRT-12-
199from crankshaft pulley.
34.Clean ancillary drive belt tensioner.
35.Position ancillary belt tensioner, fit bolts and
tighten to 25 Nm (18 lbf.ft).
36.Clean LH and RH front timing belt covers.
37.Position LH and RH front timing belt covers, fit
and tighten bolts to 4 Nm (3 lbf.ft).
38.Clean idler pulley, position pulley to engine
front mounting plate and tighten Allen bolt to 45
Nm (33 lbf.ft).
39.Position alternator to front mounting plate.