2001 LAND ROVER FREELANDER alternator

ENGINE - K SERIES KV6
12-3-66 REPAIRS
40.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
41.Connect alternator multiplug.
42.Connect battery lead to alternator, fit and
tighten nut to 8 Nm (6 lbf.ft), fit terminal cover.
43.Position PAS pump to front mounting plate, fit
and tighten bolts to 25 Nm (18 lbf.ft).
44.Position PAS pipe to engine front mounting
plate, fit and tighten bolt to 25 Nm (18 lbf.ft).
45.Clean PAS pump pulley mating faces.
46.Position PAS pump pulley, fit and tighten Torx
screws to 9 Nm (7 lbf.ft).
47.Position lower engine steady to sump
mounting, fit and tighten bolt to 100 Nm (74
lbf.ft).
48.Tighten bolt securing lower engine steady to
subframe to 100 Nm (74 lbf.ft).
49.Clean LH rear timing belt cover.
50.Position LH rear timing belt cover, fit and
tighten bolts to 4 Nm (3 lbf.ft).
51.Clean RH rear timing belt cover.
52.position RH rear timing belt cover, fit bolts and
tighten to 4 Nm (3 lbf.ft).
53.Position heat shield, fit bolts and tighten M6 bolt
to 9 Nm (7 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
54.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - from 03MY.
55.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
56.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
Camshaft timing belt cover - RH front
$% 12.65.39
Remove
1.Disconnect battery earth lead.
2.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
3.Remove 3 bolts securing camshaft timing belt
RH front cover and remove cover.
Refit
1.Clean RH front timing belt cover.
2.Position RH front timing belt cover, fit and
tighten bolts to 4 Nm (3 lbf.ft).
3.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
4.Connect battery earth lead.

ENGINE - K SERIES KV6
12-3-108 OVERHAUL
4.Remove Torx screw securing idler pulley to
front mounting plate and remove pulley.
5.Release alternator battery lead terminal cover,
loosen terminal nut and disconnect lead from
terminal
6.Disconnect multiplug from alternator.
7.Remove lower bolt and upper nut and bolt
securing alternator to front mounting plate.
8.Release alternator and remove.9.Remove 3 bolts securing camshaft timing belt
LH rear cover and remove cover.
10.Remove inlet manifold chamber - if fitted.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Remove 2 bolts securing RH rear timing belt
cover heat shield to cylinder head; remove heat
shield.
12.Remove 3 bolts securing RH rear timing belt
cover; remove cover.
M12 6694

ENGINE - K SERIES KV6
12-3-114 OVERHAUL
35.Position ancillary belt tensioner, fit bolts and
tighten to 25 Nm (18 lbf.ft).
36.Clean LH and RH front timing belt covers.
37.Position LH and RH front timing belt covers, fit
and tighten bolts to 4 Nm (3 lbf.ft).
38.Clean idler pulley, position pulley to engine
front mounting plate and tighten Torx bolt to 45
Nm (33 lbf.ft).
39.Position alternator to front mounting plate.
40.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
41.Connect alternator multiplug.
42.Connect battery lead to alternator, fit and
tighten nut to 8 Nm (6 lbf.ft), fit terminal cover.
43.Clean LH rear timing belt cover.
44.Position LH rear timing belt cover, fit and
tighten bolts to 4 Nm (3 lbf.ft).
45.Clean RH rear timing belt cover.
46.Position RH rear timing belt cover, fit bolts and
tighten to 4 Nm (3 lbf.ft).
47.Position heat shield, fit bolts and tighten M6 bolt
to 9 Nm (7 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
48.Fit inlet manifold chamber - if fitted.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
49.Position ancillary drive belt to crankshaft and
alternator pulleys.
50.Position engine mounting front bracket to
engine front plate and tighten bolts to 45 Nm
(33 lbf.ft).

FUEL DELIVERY SYSTEM - PETROL
19-2-36 REPAIRS
10.Remove fuel rail.
CAUTION: Always fit plugs to open
connections to prevent contamination.
11.Remove and discard 'O' rings from injectors.
Refit
1.Lubricate new 'O' rings with castor oil and fit to
injectors.
2.Remove plugs from inlet manifolds.
3.Position injector harness to LH fuel rail and
secure with clips.
4.Position injectors and fuel rail to inlet manifolds.
5.Connect multiplugs to injectors.
6.Position injector cover - if fitted to RH fuel rail
and secure injector harness to protection cover
or to bosses on fuel rail with clips.
7.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
8. Up to 03MY: Position ignition coils to LH inlet
manifold.
9. Up to 03MY: Position earth lead, fit nuts and
bolts securing ignition coils to LH inlet manifold
and tighten to 9 Nm (7 lbf.ft).
10.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Connect battery earth lead.
Fuel rail - KV6 - NAS
$% 19.60.04.99
Remove
1.Disconnect battery earth lead.
2.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Using a 3/8" socket bar raise ancillary drive belt
tensioner and release drive belt from alternator
and PAS pump pulleys.
5.Remove nuts and bolts securing alternator.
6.Release alternator and place aside.

FUEL DELIVERY SYSTEM - PETROL
19-2-38 REPAIRS
15.Remove fuel rail and discard 'O' rings
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Lubricate new 'O' rings with castor oil and fit to
injectors.
2.Remove plugs from inlet manifolds.
3.Position injector harness to injector protection
cover - if fitted or to bosses on fuel rail fuel rail
and secure with clips.
4.Position injectors and fuel rail to inlet manifolds.
5.Connect multiplugs to injectors.
6.Fit and tighten 4 bolts securing fuel rail to inlet
manifold to 8 Nm (6 lbf.ft).
7. Up to 03MY: Position ignition coils to LH inlet
manifold.
8. Up to 03MY: Position earth lead, fit nuts and
bolts securing ignition coils to LH inlet manifold
and tighten to 9 Nm (7 lbf.ft).
9.Position alternator and secure with nuts and
bolts, tighten to 45 Nm (33 lbf.ft).
10.Using a 3/8" square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
11.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
12.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
13.Connect battery earth lead.
Injector - KV6
$% 19.60.10
Remove
1.Disconnect battery earth lead.
2.Remove fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
3.Remove clip securing injector to fuel rail.
4.Remove injector from fuel rail, remove and
discard 'O' ring from injector.
CAUTION: Always fit plugs to open
connections to prevent contamination.
Refit
1.Clean injector and mating face in fuel rail.
2.Remove cap from new injector and fit to old
injector.
3.Lubricate new 'O' ring with castor oil and fit to
injector.
4.Fit injector to fuel rail and secure with clip.
5.Fit fuel rail.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - Non
NAS.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Fuel rail - KV6 - NAS.
6.Connect battery earth lead.

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
REPAIRS 30-3-7
Heat shield - A/C compressor - KV6 - NAS
$% 30.10.32
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and release drive
belt from alternator pulley.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Remove 3 bolts securing A/C compressor to
fixing brackets and position compressor aside.
6.Remove compressor heat shield.Refit
1.Clean compressor and mounting bracket
mating faces.
2.Fit compressor heat shield.
3.Position compressor to mounting and align
heat shield. Fit and tighten bolts to 25 Nm (18
lbf.ft).
4.Using a 3/8" square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
5.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.
M30 1142

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-12 REPAIRS
Gasket(s) - exhaust manifold - LH - NAS
$% 30.15.17
Remove
1.Position vehicle on 4 post ramp.
2.Disconnect battery earth lead.
3.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Using a 3/8" socket bar raise ancillary drive belt
tensioner and release drive belt from alternator
and PAS pump pulleys.
6.Remove 3 bolts securing A/C compressor to
fixing brackets and position compressor aside.
7.Remove compressor heat shield.8.Release and disconnect HO2S multiplug.
9.Release HO2S harness from clip.
10.Release and disconnect post catalyst HO2S
multiplug.
11.Release HO2S harness from clips.
12.Remove 2 nuts securing exhaust front pipe to
exhaust manifold.
M30 1142
M19 3505
M19 3481

STEERING
57-12 REPAIRS
Pump - steering - KV6
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove engine mounting top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
3.Loosen PAS pump pulley bolts.
4.Using a 3/8" socket bar, raise ancillary drive
belt tensioner and release drive belt from
alternator and PAS pump pulleys.
5.Position container to collect PAS fluid spillage.6.Release clip and disconnect fluid inlet hose
from PAS pump.
7.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
8.Remove bolt securing PAS outlet pipe support
bracket to cylinder head and move pipe aside.
9.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.
CAUTION: Always fit plugs to open
connections to prevent contamination.