1999 SUBARU LEGACY Service Repair Manual

16) Disconnect spark plug cords from ignition coil
and ignitor assembly.
B2M2312
17) Disconnect PCV hose assembly from intake
manifold.
B2M2313
18) Disconnect engine coolant hoses from throttle
body.
B2M2299
19) Disconnect brake booster hose.
B2M2314
20) Remove air cleaner case stay RH and engine
harness bracket, and disconnect engine harness
connectors from bulkhead harness connectors.21) Pull out engine harness connector from
bracket.
B2M2315
22) Disconnect connectors from engine coolant
temperature sensor (A) and thermometer (B).
B2M0345B
23) Disconnect knock sensor connector.
B2M2327A
24) Disconnect connector from camshaft position
sensor.
B2M2317B
28
2-7[W4A1]SERVICE PROCEDURE
4. Intake Manifold

25) Disconnect connector from crankshaft position
sensor.
B2M1252A
26) Disconnect connector from oil pressure
switch.
B2M1253A
27) Disconnect fuel hoses from fuel pipes.
WARNING:
Catch fuel from hoses in a container.
S2M0500
28) Remove eight bolts which hold intake manifold
onto cylinder heads.
B2M2318
29) Remove intake manifold.
B2M0160
2. 2200 cc EXCEPT CALIFORNIA SPEC.
VEHICLES
1) Release fuel pressure.
2) Open fuel flap lid, and remove fuel filler cap.
B2M1746
3) Disconnect battery ground cable.
B2M1723
4) Disconnect connector from mass air flow sen-
sor.
B2M2018
29
[W4A2]2-7SERVICE PROCEDURE
4. Intake Manifold

5) Loosen clamp which connects air intake cham-
ber to throttle body.
B2M2769
6) Remove two clips of air cleaner upper cover.
B2M2289
7) Remove bolts which install air intake chamber
on stays.
B2M2770
8) Disconnect blow-by hose from air intake cham-
ber.
9) Remove air intake duct, air cleaner upper cover
and air intake chamber as a unit.
10) Remove air cleaner element.
B2M2347
11) Disconnect accelerator cable (A).
12) Disconnect cruise control cable (B). (With
cruise control model)
B2M2302A
13) Disconnect vacuum hoses from pressure
sources switching solenoid valve.
14) Remove power steering pump from bracket.
(1) Remove V-belt cover.
B2M2307
(2) Loosen lock bolt and slider bolt, and remove
power steering pump drive V-belt.
B2M2308
30
2-7[W4A2]SERVICE PROCEDURE
4. Intake Manifold

(3) Remove bolts which secure power steering
pipe brackets to intake manifold.
NOTE:
Do not disconnect power steering hose.
B2M2309
(4) Remove bolts which install power steering
pump to bracket.
B2M2310
(5) Remove bolt which holds power steering
fluid tank bracket onto cylinder block.
B2M2325
(6) Place power steering pump on the right side
wheel apron.
B2M2293
15) Remove fuel pipe protector LH. (LHD model
only)
B2M2754
16) Remove fuel pipe protector RH. (RHD model
only)
B2M2755
17) Disconnect spark plug cords from ignition coil
and ignitor assembly.
B2M2312
31
[W4A2]2-7SERVICE PROCEDURE
4. Intake Manifold

18) Disconnect PCV hose (A) and pressure regu-
lator vacuum hose (B) from intake manifold.
19) Disconnect vacuum hose (C) to cruise control
diaphragm. (With cruise control models)
S2M0089A
20) Disconnect engine coolant hose from throttle
body.
B2M2304
21) Disconnect brake booster hose.
B2M2314
22) Remove air intake chamber stay RH, engine
harness bracket from transmission housing, and
disconnect engine harness connectors from bulk-
head harness connectors.
B2M2315
23) Disconnect connectors from engine coolant
temperature sensor (A) and thermometer (B).
B2M0345B
24) Disconnect knock sensor connector.
B2M2327A
25) Disconnect connector from camshaft position
sensor.
B2M2317B
32
2-7[W4A2]SERVICE PROCEDURE
4. Intake Manifold

26) Disconnect connector from crankshaft position
sensor.
B2M1252A
27) Disconnect connector from oil pressure
switch.
B2M1253A
28) Disconnect fuel hoses from fuel pipes.
WARNING:
Catch fuel from hoses in a container.
S2M0500
29) Remove bolts which hold intake manifold onto
cylinder heads.
B2M2318
30) Remove intake manifold.
B2M0160
3. 2500 cc MODEL
1) Release fuel pressure.
2) Open fuel flap lid, and remove fuel filler cap.
B2M1746
3) Disconnect battery ground cable.
B2M1723
4) Disconnect connector from mass air flow sen-
sor.
B2M1225A
33
[W4A3]2-7SERVICE PROCEDURE
4. Intake Manifold

5) Loosen clamp which connects air intake cham-
ber to throttle body.
S2M0096
6) Remove two clips of air cleaner upper cover.
B2M2289
7) Remove bolts which install air intake chamber
on stays.
S2M0092
8) Disconnect blow-by hose from air intake duct.
9) Remove air intake duct, air cleaner upper cover
and air intake chamber as a unit.
10) Remove air cleaner element.
S2M0084
11) Disconnect accelerator cable (A).
12) Disconnect cruise control cable (B). (With
cruise control model)
B2M1190A
13) Remove power steering pump from bracket.
(1) Remove V-belt covers.
B2M2307
(2) Loosen lock bolt and slider bolt, and remove
power steering pump drive V-belt.
B2M2308
34
2-7[W4A3]SERVICE PROCEDURE
4. Intake Manifold

(3) Remove bolts which secure power steering
pipe brackets to intake manifold.
NOTE:
Do not disconnect power steering hose.
S2M0085
(4) Remove bolts which install power steering
pump to bracket.
B2M2310
(5) Place power steering pump on the right side
wheel apron.
B2M2293
14) Disconnect spark plug cords from ignition coil.
B6M0772
15) Disconnect PCV hose (A) and vacuum hose
(B) from intake manifold.
H2M2440A
16) Disconnect engine coolant hose from throttle
body.
B2M1248
17) Disconnect engine coolant hose (A) from idle
air control solenoid valve.
18) Disconnect air by-pass hose (B) from idle air
control solenoid valve.
H2M1259B
19) Disconnect brake booster hose.
B2M2314
35
[W4A3]2-7SERVICE PROCEDURE
4. Intake Manifold