2003 SSANGYONG MUSSO Service Manual

1B3-64 OM600 ENGINE MECHANICAL
8. Remove the guide pulley bracket (24).
Tools Required
116 589 03 07 00 Socket Wrench Removal Procedure
1. Remove the fan clutch and cooling fan belt pulley.
2. Drain the engine oil completely.
3. Remove the oil dipstick tube bracket bolts.
4. Remove the crankshaft pulley.
5. Loosen the bolt (1) and then remove the cylinder head cover(2) and gasket.
6. Remove the vacuum pump.
7. Detach the closing cover (20). Remove the bolts(21) and then remove the guide pulley (22).

OM600 ENGINE MECHANICAL 1B3-65
11. Remove the alternator bracket (16).
9. Disconnect the pipes of power steering pump and removethe belt pulley. Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then remove the power steering pump.
12. Remove the fuel filter.

1B3-66 OM600 ENGINE MECHANICAL
18. Remove the timing case cover (19) bolts and then removethe timing case cover (14). Notice Be careful not to damage the cylinder head gasket or oil pan gasket.
13. Remove the camshaft.
14. Remove the socket bolts(4) in the chain box.
Socket Wrench 115 589 03 07 00
15. Remove the injection pump. NoticeSee the ‘Removal of fuel injection pump ’.
16. Remove the oil pan bolts (8, 9) in the area of the timing case cover (14).
17. Slightly loosen the remaining oil pan bolts.

OM600 ENGINE MECHANICAL 1B3-67
Installation Procedure
1. Thoroughly clean the sealing surface and apply sealant.
2. Install the timing case cover.Notice Bolts arrangement
1.M6 x 60
2.M6 x 70
3.M6 x 40
3. Tighten the socket bolts in the chain box.
Tightening Torque 10 Nm
Tightening Torque 23 Nm
4. Tighten the oil pan bolts.
Tightening Torque 10 Nm 10 Nm23 Nm
Socket bolt
M6 bolt M8 bolt

1B3-68 OM600 ENGINE MECHANICAL
Tightening Torque25 Nm
5. Install the flange, vibration damper and crankshaft belt
pulley. Notice
Replace front radial seal if necessary.
6. Install the alternator bracket.
25 Nm
Front
Side
7. Install the alternator
Tightening TorqueUpper - 25 Nm Low - 25 Nm
8. Install the cylinder head cover.
Tightening Torque 10 Nm
9. Tighten the injection pump mounting bolts.
Tightening Torque 23 Nm

OM600 ENGINE MECHANICAL 1B3-69
10. Install the fuel filter.
11. Install the vacuum pump.
12. Install the power steering pump.
13. Install the power steering pump pulley.
Tightening Torque 25 Nm
Tightening Torque 10 Nm
Tightening Torque 23 Nm
Tightening Torque 32 Nm
14. Install the guide pulley bracket.
Tightening Torque 9 Nm

1B3-70 OM600 ENGINE MECHANICAL
15. Install the guide pulley (22) and fit the closing cover (20).
16. Replace the gasket (3) and install the cylinder head cover(2).
17. Install the cooling fan belt pulley and fan clutch.
18. Install the belt tensioning device and then install the belt.
19. Install the cooling fan.
20. Fill the engine oil and check oil leaks by running the engine.
Tightening Torque 23 Nm
Tightening Torque 10 Nm

OM600 ENGINE MECHANICAL 1B3-71
CRANKSHAFT END COVER Preceding Work : Removal of flywheel and driven plate.
1 Crankshaft Flange
2 End Cover.............................. Clean, Loctite 573
3 Bolt ......................................... 10Nm, Loctite 5734 Radial Seal
............................................ Replace
5 Dowel Sleeve
6 Bolt ......................................... 10Nm, Loctite 573