2003 SSANGYONG MUSSO solenoid

M162 ENGINE MECHANICAL 1B1-13
20. Disconnect following sensors connector.HFM sensor.
Coolant temperature sensor.
2 knock sensors.
Camshaft and crankshaft sensors.
21. After removing the ignition coil cover, disconnect the ignition coil connector.
22. Remove the harness cover and disconnect the 6 injection valve connectors. Disconnect the main harness
23. Separate the hose toward engine from canister purge solenoid valve.
24. Remove the automatic transmission oil cooler line.

1B2-14 M161 ENGINE MECHANICAL
20. Disconnect following sensors connector.HFM sensor.
Coolant temperature sensor.
2 knock sensors.
Camshaft and crankshaft sensors.
21. After removing the ignition coil cover, disconnect the ignition coil connector.
22. Remove the harness cover and disconnect the 6 injection valve connectors. Disconnect the main harness.
23. Separate the hose toward engine from canister purge solenoid valve.
24. Remove the automatic transmission oil cooler line.

1F1-18 M162 ENGINE CONTROLS
Failurecode Item

18.1
Checking method
Test
stepRequirementSpecified
value Possible cause
73 2 8 - 12




Camshaft
actuator: Solenoidresistance
21.0 


Purge
control valve:- Vacuum control 
Engine:in idling/
normal operatingtemperature 
Vacuum line
 Purge control valve

Cable
 Camshaft actuator
Diagnosis socket
19.0
73 69 Engine is
unstable or stopped



Camshaft
actuator:MechanicalActuation
 Mechanical failure of
camshaft actuator
20.0 
Engine:in idling
34 11 The purge
control valve should be
operated after approx.
1minute.
(refer to figure 5)



Purge
control valve:- Operating226, 227,
 ECU
 Cable
 Purge control valve
 Ignition:ON 0.3 - 0.5 A
- Current
consumption
10 34
Creating
above 50mbar of vacuum
after approx. 1 minute
22.0 
Ignition:OFF
38 37 
Data bus
 22.1
 22.2
55 - 65




CAN data
bus
 Ignition:OFF

Engine:in idling
- connect the bridge to the test box for approx. 10 seconds
40, 41,54,
Connect the vacuum gauge between thecontrol valve andcanister
22,23, 24,26,27,29,30,31,59,60,

OM600 ENGINE CONTROLS 1F3-5
VACUUM CONTROL SYSTEM TEST
2 Engine Cut-Off Valve (Ignition Key Switch)
3 Auto-locking Hub Solenoid Valve
4 Engine Stop Valve Unit
5 PLA Vacuum Unit (Idle Speed Adjustment)
6 Engine
7 Vacuum Pump830
° Thermovalve
9 Fuel Injection Pump
10 Filter with Restriction
11 Check V alve
12 Modulating Pressure Line (Automatic T/M)
Test Data
Idle Speed Increase Permissible Pressure Drop of System At least 100 rpm at approx. 500mbr
400 - 500mbar approx. 1 min.

FRONT DRIVE AXLE 3A-5
VACUUM CIRCUIT
1 Engine
2 Vacuum Pump
3 3-way Connector
4 T-connector
5 Check Valve 6 Auto locking Hub Solenoid Valve
7 T-connector Hose
8 Hub Hose (left)
9 Hub Hose (right)

3A-6 FRONT DRIVE AXLEMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
VACUUM LINE
1 Vacuum Auto-locking Hub Assembly
2 Bolt ...................................................... 50-60 Nm
3 Cam Washer
4 Auto-locking Hub Cap
5 Retainer Ring
6 Shim
7 Locking Hub
8 Band
9 Hose (L : 400)
10 T-connector 11 Hose (L : 250, white)
12 Check V alve
13 Hose (L :100, green)
14 Auto Locking Hub Solenoid Valve
15 Bolt
16 Hose (L :100, green)
17 T-connector
18 Hose (L : 720, yellow)
19 Hose (L :2, 360 , red)
20 Corrugated Tube
21 Clip
22 Clip

FrontRear
Front Rear
SECTION 4F
ANTILOCK BRAKE SYSTEM
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Model
ECUNumber of Pins
Operating TemperatureMotor Operating CurrentSolenoid Coil Resistance External Resistance Air Gap
Number of teeth Description
ABS 5.3 31
-40 ~ +120 °C
Below MAX 40A
1.28K - 1.92K
0.35 - 1.60 mm 0.15 - 1.20 mm 52 52 ABS/ABD 5.3
83
-40 ~ +85 °C
Below MAX 45A
8.04 - 9.04 except AV,
HSV 4.04 - 4.54
1.28K - 1.92K
0.35 - 1.60 mm 0.15 - 1.20 mm
52 52
Hydraulic System
Wheel Speed Sensor Impulse Ring
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4F-1
General Specifications . . . . . . . . . . . . . . . . . . 4F-1
Schematic and Routing Diagrams . . . . . . . . 4F-2 ABS 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-2
ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-3
ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-4
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . 4F-5
Component Locator . . . . . . . . . . . . . . . . . . . 4F-6 ABS, ABS/ABD . . . . . . . . . . . . . . . . . . . . . . . . 4F-6
ABD System Description . . . . . . . . . . . . . . . 4F-7 Self Diagnosis . . . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . 4F-9
ABS, ABS/ABD 5.0 . . . . . . . . . . . . . . . . . . . . 4F-11
Defect Codes . . . . . . . . . . . . . . . . . . . . . . . . 4F-13
Maintenance and Repair . . . . . . . . . . . . . . 4F-19
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 4F-19
Wheel Speed Sensor . . . . . . . . . . . . . . . . . . 4F-19
Hydraulic Circuit . . . . . . . . . . . . . . . . . . . . 4F-21 ABS 5.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4F-21
ABS/ABD 5.3 . . . . . . . . . . . . . . . . . . . . . . . . 4F-24

ANTILOCK BRAKE SYSTEM 4F-15
Description
Check each valve by using SCANNER's solenoid valve overriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check each valve by using SCANNER's solenoid valveoverriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short. (When connector is removed)
Replace the hydraulic modulator.
Check each valve by using SCANNER's solenoid valve overriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short. (When connector is removed)
Replace the hydraulic modulator.
Check each valve by using SCANNER's solenoid valve overriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short.(When connector is removed)
Replace the hydraulic modulator.
Check each valve by using SCANNER's solenoid valveoverriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short.(When connector is removed)
Replace the hydraulic modulator.
Check each valve by using SCANNER's solenoid valveoverriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short.(When connector is removed)
Replace the hydraulic modulator.
Check each valve by using SCANNER's solenoid valveoverriding function.
Check connection of connector and terminals in the
ECU hydraulic modulator.
Check terminals for open or short.
Application
Front / left INLET Valve
Front / left OUTLET Valve
Front / right INLET Valve
Front / right OUTLET Valve
Rear / left INLET Valve (ABD)
Rear / left OUTLET Valve
Rear / Right INLET ValveDefect Code
13 14 15 1617 18 19