2003 SSANGYONG MUSSO Service Manual

OM600 ENGINE CONTROLS 1F3-47
2. Remove the connecting rod (9).
3. Disconnect the vacuum lines (13, 14).
4. Remove the accelerator control damper (10).(Manual transmission vehicle)
5. Remove the suction line (16) and pressure line (4).
6. Remove the banjo bolt (1) and then remove the seal (2) and fuel line (3).
7. Remove the plastic clip (8) on the injection line.
Removal Procedure
1. Position then no.1 cylinder at 15
° ATDC.
Notice Do not rotate the engine in opposition direction of engine rotation.
8. Disconnect the injection lines (15) from the injection pump (25).
9. Remove the banjo bolt (1) and then remove the seal (7) and return line (5).

1F3-48 OM600 ENGINE CONTROLS
10. Install the assembly cage (29) and remove the bolt (20)and pull off the washer (21). Notice Be careful that the bolt (20) is left hand thread.
Assembly Cage 601 589 05 14 00
11. Remove the chain tensioner (18) and seal (19).
12. Remove the bolt (12) and pull off the washer (11).
13. Remove the bolt (22) and pull off the square nut (28).
14. Pull out the fuel injection pump (25) and seal (23).

OM600 ENGINE CONTROLS 1F3-49
Installation Procedure
1. Remove the screw plug (27) and seal (26) and collect oil ina vessel.
2. Insert flange (31) onto the injection pump camshaft and turn until the cam of the governor is visible in the hole.
Flange 601 589 00 08 00
3. Tighten the locking screw. Locking Screw 601 589 05 21 00
4. Ensure that the No.1 cylinder is positioned at A TDC 15°.

1F3-50 OM600 ENGINE CONTROLS
10. Connect the fuel pipesNotice Replace the seal. Box Wrench Insert 000 589 77 03 00
Return Line Fuel Injection LineFuel feed LineSuction and Pressure Line 46 Nm18 Nm13 Nm13 Nm
5. Coat the new seal (23) with engine oil and install it.
6. Insert the fuel injection pump (25) and tighten the bolts
(22).
7. Remove the locking screw (32).
Tightening Torque 23 Nm
8. Tighten the bolt(12).
9. Insert the washer (21) and tighten the bolts (20) and then remove the assembly cage (29).
Tightening Torque 23 Nm
Tightening Torque 46 Nm

OM600 ENGINE CONTROLS 1F3-51
12. Connect the vacuum line (13, 14).
13. Connect the connecting rod (9).
14. Connect the accelerator control damper (10).(Manual transmission vehicle)
15. Install the chain tensioner.
16. Install the vacuum pump.
17. Check the start of delivery.
18. Adjust the idle speed.
11. Assemble the plastic clip (8).

SECTION 1G1
M162 ENGINE INTAKE & EXHAUST
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G1-1Fastener Tightening Specifications . . . . . . . . 1G1-1
Maintenance and Repair . . . . . . . . . . . . . . 1G1-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1G1-2
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 1G1-2
TABLE OF CONTENTS
Intake Air Duct . . . . . . . . . . . . . . . . . . . . . . . 1G1-4
Intake Manifold . . . . . . . . . . . . . . . . . . . . . . . 1G1-5
Resonance Flap . . . . . . . . . . . . . . . . . . . . . . 1G1-7
Exhaust Manifold . . . . . . . . . . . . . . . . . . . . . 1G1-9
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
N m
9 - 11
22.5 - 27.5 22.5 - 27.5 9.5 - 12.5 15 - 28 28 - 47
Application
Air Cleaner Housing Cover NutIntake Manifold Bolt (M8 x 20) Intake Manifold Bolt (M8)Exhaust Mainfold Stud BoltExhaust Pipe Nut (Engine) Exhaust Pipe Bolt

1G1-2 M162 ENGINE INTAKE & EXHAUSTMAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AIR CLEANER
1 Air - Cleaner Assembly
2 Air - Cleaner Shield Upper Cover
3 Blot4 Blot
5 Air Intake Shield

M162 ENGINE INTAKE & EXHAUST 1G1-3
Removal & Installation Procedure1. Release the clamp securing HFM sensor and air cleaner.
2. Disengage the air cleaner assembly and HFM sensor assembly.
3. Unserew the mounting bolt(6) from the bracket.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm
4. Release the clamp from air cleaner assembly housing and remove the cover.
5. Remove the air cleaner assembly.
6. Remove the air cleaner housing from insulator.
Notice
Make sure the air cleaner to be seated in insulator.
7. Disengage the air duct hose and air cleaner housing and remove the housing.
8. Remove the air duct hose.
9. Unscrew the two bolts(7) from air inlet duct. Installation Notice
10. Remove the air inlet duct.
11. Installation should follow the removal procedure in the reverse order.
Tightening Torque 8 - 9 Nm