Page 1993 of 4133

AR88.20-P-2200GJ
Remove/install rear bumper
6.4.99
MODEL
163.113 /128 /136 /154 /157 /172 /175 with CODE (U49) Styling package
MODEL
163.174
P88.20-2090-09
Remove/install
1.1
Separate antenna of emergency call system
E-Call connector
Only with E-call emergency call system,
code 349. The connector is located behind
the side flap of the right C-pillar paneling at
the jack socket point.
2
Unscrew screws (A) on energy absorber
retaining straps at bottom of cross member
2 each.
*BA88.20-P-1005-01B
3
Pull cover strip off of screws (B) at top of
bumper
Velcro strips
4
Unscrew screws (B) at top of bumper
*BA88.20-P-1005-01B
5
Pull bumper to the rear and remove
Do not damage paintwork/wiring harness.
Installation:
Align bumper at tailgate and
at taillamps.
6.1
Remove rubber seal of antenna of emergency
call system E-Call on right at body
Only with emergency call system E-Call,
Code 349.
7.1
Disconnect connector from Parktronic system
Only with Parktronic system (PTS), code
220a. Remove left rubber seal at body.
8
Install in the reverse order
Bumper
Number
Designation
Model 163
BA88.20-P-1005-01B
Screws, rear bumper to frame
Nm
8
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1994 of 4133

AR88.20-P-2000GH
Remove/install front bumper
14.3.97
MODEL
163.113 /154 #A up to 289564,
163.113 #X up to 754619,
163.154 #X up to 716524,
163.136 /172 except CODE (U49) Styling package
P88.20-0375-09
1
Nut
2
Nuts
1a
Screw
Remove/Install
1.1
Remove brush guard together with underride
guard
If installed.
AR88.30-P-2000-01GH
*BA88.30-P-1002-01A
*BA88.30-P-1003-01A
*BA88.30-P-1011-01A
*BA88.30-P-1015-01A
*BA88.30-P-1016-01A
2
Unscrew nut (1)
Left and right at inside.
*BA88.20-P-1001-01B
3
Unscrew bolt (1a)
Left and right at inside.
*BA88.20-P-1002-01B
4
Remove front bumper grille.
Carefully remove front bumper grille so
that bumper grille and bumper grille mount
cannot be damaged.
Loosen retainers and pull to outside
Pulling hook
*140589023300
5.1
Remove outside temperature sensor from
front bumper.
If installed.
6
Unscrew nuts (2)
*BA88.20-P-1003-01B
7
Remove bumper toward front.
Do not damage paint.
8
Install in the reverse order
Detachable body components, underride guard
Number
Designation
Model 163
up to
31.8.01
BA88.30-P-1002-01A
Nut, spacer tube on brush guard
Nm
86
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1995 of 4133
BA88.30-P-1003-01A
Screw, mount on brush guard
Nm
49
BA88.30-P-1011-01A
Bolt, underride guard to brush guard
Nm
25
BA88.30-P-1015-01A
Nut, underride guard to bracket
Nm
49
BA88.30-P-1016-01A
Bolt, front section of underride guard to rear
section of underride guard
Nm
49
Bumper
Number
Designation
Model 163
BA88.20-P-1001-01B
Nut, front bumper on outer mount
Nm
8
BA88.20-P-1002-01B
Screw for front bumper on inner mount
Nm
1.5
BA88.20-P-1003-01B
Nut, front bumper on frame
Nm
8
Pulling hook
140 589 02 33 00
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2
Page 1996 of 4133

AR88.20-P-2000GJ
Remove/install front bumper
26.2.01
MODEL
163.113 /154 #A as of 289565,
163.113 #X as of 754620,
163.128 /154 /157 /175 except CODE (U49) Styling package
P88.20-2203-09
Remove/install
1.1
Remove brush guard together with underride
guard
If installed.
AR88.30-P-2000-01GI
*BA88.30-P-1003-01A
*BA88.30-P-1015-01A
*BA88.30-P-1016-01A
2
Remove fog lamps
AR82.10-P-5103GI
3
Remove front bumper grille.
Carefully remove bumper grille so that
bumper grille and mounts cannot be damaged.
Remove with correspondingly formed hook.
Pulling hook
*140589023300
4
Remove outdoor temperature sensor from
bumper.
5
Unscrew screws (1)
At front side of bumper.
*BA88.20-P-1009-01B
6
Unscrew bolt (2)
At inner bumper corners.
*BA88.20-P-1002-01B
7
Unscrew nuts (3).
At inner sides of bumper.
*BA88.20-P-1001-01B
8
Loosen side mount on bumper from body.
Loosen only one side. Move mount
toward inside.
9
Remove bumper toward front.
Do not damage paint. Do not damage
Parktronic connection cable if present.
Installation:
Observe correct installation
position of fog lamps.
10.1
Disconnect connector from Parktronic system
Only with Parktronic system (PTS), code
220a.
11
Install in the reverse order
Detachable body components, underride guard
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1997 of 4133
Number
Designation
Model 163
as of
1.9.01
BA88.30-P-1003-01A
Screw, mount on brush guard
Nm
25
BA88.30-P-1015-01A
Nut, underride guard to bracket
Nm
49
BA88.30-P-1016-01A
Bolt, front section of underride guard to rear
section of underride guard
Nm
49
Bumper
Number
Designation
Model 163
BA88.20-P-1001-01B
Nut, front bumper on outer mount
Nm
8
BA88.20-P-1002-01B
Screw for front bumper on inner mount
Nm
1.5
BA88.20-P-1009-01B
Screw for front bumper on mountNm
8
Pulling hook
140 589 02 33 00
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2
Page 1998 of 4133

AR88.20-P-2200GJ
Remove/install rear bumper
6.4.99
MODEL
163.113 /128 /136 /154 /157 /172 /175 with CODE (U49) Styling package
MODEL
163.174
P88.20-2090-09
Remove/install
1.1
Separate antenna of emergency call system
E-Call connector
Only with E-call emergency call system,
code 349. The connector is located behind
the side flap of the right C-pillar paneling at
the jack socket point.
2
Unscrew screws (A) on energy absorber
retaining straps at bottom of cross member
2 each.
*BA88.20-P-1005-01B
3
Pull cover strip off of screws (B) at top of
bumper
Velcro strips
4
Unscrew screws (B) at top of bumper
*BA88.20-P-1005-01B
5
Pull bumper to the rear and remove
Do not damage paintwork/wiring harness.
Installation:
Align bumper at tailgate and
at taillamps.
6.1
Remove rubber seal of antenna of emergency
call system E-Call on right at body
Only with emergency call system E-Call,
Code 349.
7.1
Disconnect connector from Parktronic system
Only with Parktronic system (PTS), code
220a. Remove left rubber seal at body.
8
Install in the reverse order
Bumper
Number
Designation
Model 163
BA88.20-P-1005-01B
Screws, rear bumper to frame
Nm
8
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 1999 of 4133

AR88.20-P-2200GI
Remove/install rear bumper
11.4.97
MODEL
163.113 #A up to 289564,
163.113 #X up to 754619,
163.154 #A up to 289564,
163.154 #X up to 716524,
163.136 /172 with CODE (849) Spare wheel carrier/spare wheel
P88.20-0369-09
A
Nuts
B
Nut
E
Nuts
C
Screws
D
Spare wheel carrier consoles
Remove/Install
1.1
Disconnect antenna connector of E-call
emergency call system
Only with emergency call system E-Call,
code 349.
Connector is located behind side flap of right
C-pillar paneling at jack mounting point.
2
Unscrew nuts (A)
On vehicle underbody behind cross
member
3
Unscrew nut (B)
On vehicle underbody behind cross
member
4
Unscrew bolts from spare wheel carrier
console
Do not damage bolt thread
Bolts fastened with nuts (A) can be driven
out from the rear of the cross member.
5
Remove spare wheel carrier consoles (D)
6
Remove 3 panels from bumper
Do not damage paint. Do not break off
clips.
Long wedge
*115589035900
7
Unscrew bolts (C) from bumper
*BA88.20-P-1007-01B
8
Unscrew nuts (E) from bumper
*BA88.20-P-1006-01B
9.1
Remove nut from rear mud guard
Only if present
*BA88.30-P-1004-01A
10
Remove bumper
Do not damage paintwork on vehicle and
bumper.
Completely turn spare wheel carrier to
rear (maximum clearance for bumper). Pull
bumper to rear and then lift out upward
between spare wheel carrier and vehicle.
Installation:
Align bumper at tailgate and
at taillamps
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
Page 2000 of 4133
11.1
Remove rubber seal for E-call emergency call
system antenna from body at right
Only with emergency call system E-Call,
code 349.
12
Install in the reverse order
Bumper
Number
Designation
Model 163
BA88.20-P-1006-01B
Nuts for rear bumper on cross member
Nm
8
BA88.20-P-1007-01B
Screws for rear bumper on cross member,
rear
Nm
8
Designation
Model 163
up to
31.8.01
BA88.30-P-1004-01A
Nut for retaining strap on mud guard on vehicle
underbody
Nm
6
Long wedge
115 589 03 59 00
Copyright DaimlerChrysler AG 20.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2