1992 MAZDA PROTEGE Workshop Manual

MOLDING. PROTECTOR, GARNISH S
SIDE PROTECTOR
Removal / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Install in the reverse order of removal, referring to Installation Note.
Caution
l Remove the side protector carefully to prevent damage to the painted surface.
PROTEGk
HATCHBACK
1. Protector No.1 2. Protector No.2 3. Protector No.3
Removal Note . . page S-49 Removal Note . . page S-49 Removal Note ,. page S-49
Installation Note page S-50 Installation Note page S-50 Installation Note page S-50
03UOSX-068
Removal Note
Protector
1. Using a screwdriver or knife, twist the protector end, being
careful not to damage the painted surface, and separate
the adhesive for
20-30mm (0.79-1.18 in).
2. Pull the separated portion to remove it.
s-49

S MOLDING, PROTECTOR, GARNISH
I 03UOSX-06
PRIMER 9
I
I 03uosx-070
BONDING AGENT
DOUBLE-SIDED ADHESIVE TAPE
03uosx-071
Installation Note
Protector
1. Use a knife to remove the adhesive remaining on the body
and protector.
Note
l Remove as much adhesive as possible without
damaging the painted surface.
l If the adhesive is difficult to remove, soften it with
a hot air blower.
2. Remove any grease or dirt from the protector and body
adhesion surface.
3. Apply primer to the protector as shown.
4. Attach double-sided adhesive tape to the protector (when
reused).
5. Apply adhesive (polyurethane) to the protector as shown.
6. Mark the installation position on the body with masking tape.
7. Align the protector on the body and attach it securely.
Note
l Adhesion conditions deteriorate if air temperature
is below 20°C (66OF); heating of the body is recom-
mended.
I 03UOSX-072
s-50

RADIATOR GRILLE, LOWER GRILLE MOLDING S
RADIATOR GRILLE, LOWER GRILLE MOLDING
COMPONENTS
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal, referring to Installation Note.
1. Radiator grille 3. Lower grille molding
Installation Note. . . . . . . . . . . . . . . . . . . . .
page S-51 4. Clip
2. Front combination light
Removal I Installation ..,.,,...,..,........ Section T
Installation Note
Radiator grille
1. Insert the clips into the grille, and align them with the instal-
lation holes in the body.
2. Press the grille into the body.
s-51

S REAR FINISHER
REAR FINISHER
COMPONENTS
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
HATCHBACK
Hatchback PROTEGE
1. Rear hatch lower trim 4. License plate light
Removal / Installation . . . . . . . . . . . . . . . . . . page S-98 5. Rear finisher 2. Rear finisher 6. Packing
3. Packing
S-52

COWL GRILLE, EXTRACTOR CHAMBER
COWL GRILLE
COMPONENTS
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
r-
-140 cm-kg, 87-122 i
kg, 87-122 in-lb)
1. Wiper arm cover 3. Cowl cap
2. Wiper arm and blade
4. Cowl grille
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-73
EXTRACTOR CHAMBER
COMPONENTS
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
1. Rear bumper
Removal I Installation . . . . . . . . . . . . . . . . . . page S-40
2. Extractor chamber
s-53

S
OUTSIDE MIRROR
TROUBLESHOOTING GUIDE
Circuit Diagram
OUTSIDE MIRROR
IPOWER OUTSIDE MIRROR L
BATTERY
MAIN
80A
B (E) B (F)
ITION
TCH
HAD10
15A -
::P \\o-rol/
JB-02 JB-06
0 G3
$?L-0 1 POWER OUTSIDE MIRROR SWITCH
up r---~~~---------_--_ DOWN
I’ ‘
DOWN p UP
,c
LEFT 6 RIGHT
---o -
‘\.------ ------- -___-l/’
L-01
-RIGHT
MIRROR MOTOR
-01 POWER OUTSIDE MIRROR SWITCH(I) L.-O2 DRI-MIRROR
.-

OUTSIDE MIRROR S
Power outside mirror does not operate
I
I VB: Battery voltage
Check RADIO 15A fuse Repair harness and replace fuse OK
Turn ignition switch ON
I.’
Check for battery voltage at terminal-wire (LIB) of NG
_ Repair harness
power outside mirror switch (Fuse box-Power outside mirror switch) OK
1
I
Disconnect power outside mirror switch connector;
check for continuity of connector terminal-wire (B) to
ground Repair harness (Power outside mirror switch-Ground)
Check power outside mirror switch
(Refer to page S-55) OK
- Replace power outside mirror switch NO
(Refer to page S-55)
Reconnect power outside mirror switch connector;
disconnect remote control mirror connector, and check
for battery voltage at terminals while operating switch
I IP
NG
_ Repair harness
(Power outside mirror switch-Power outside mirror)
VI
DOWN
LEFT
RIGHT OK
Check power outside mirror (Refer to page S-56) I I
23UOSX-016
POWER OUTSIDE MIRROR SWITCH
Inspection
1. Remove the power outside mirror switch.
(Refer to page S-56.)
2. Check for continuity between terminals with an ohmmeter.
23UOSX-04
TermIn:
-1
I I
UP 0’
LEFT 0
0
o---O: Indicates continuity

OUTSIDE MIRROR
c a
23UOSX.042
POWER OUTSIDE MIRROR
Inspection
1. Remove the power outside mirror. (Refer to page S-56.)
2. Check for continuity between terminals with an ohmmeter.
I
Terminal I
t
a C d
0 I
A I
0
o--O : indicates continuity
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable. (With power outside mirror.)
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
MANUAL CONTROL
S-56