1992 MAZDA PROTEGE Workshop Manual

FRONT DOOR S
03uosx-01’
PROTEGk 6
f 1.5 (0.24 f 0.06)
HATCHBACK: 6.3
f 1.5 (0.25 f 0.06
mm (in)
Adjustment Note
Door lock striker
1. Verify that the door can be closed easily and that there is
no looseness. If there is a problem, loosen the striker mount-
ing screws and adjust by moving the striker vertically or
laterally.
2. Check the rear offset of the door to the body (or rear door).
If there is a problem, adjust it by moving the door lock striker
laterally.
Tightening torque:
18-28 N-m (1.8-2.7 m-kg, 13-20 ft-lb)
Note
l Use a TORX drive bit for removal/installation of the
door lock striker.
Front door
Loosen the hinge bolts and adjust as shown in the figure. Tight-
en the bolts to the specified torque.
Tightening torque:
18-29 N-m (1.8-3.0 m-kg, 13-22 ft-lb)
s-9

FRONT SIDE WINDOW REGULATOR AND GLASS
FRONT SIDE WINDOW REGULATOR AND GLASS
COMPONENTS
Removal / Installation
1, Raise the front door glass 1 1Omm (4.33 in) from the fully open position.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
Note
l Refer to page S-56; Removal of the door mirror for removal of the inner garnish.
-lATCHBACK
9 9
61-67 in-lb)
61-67 in-lb
1.1 . . v.. (70-100 cm-kg, 61-67 in-lb)
1. Regulator handle (Manual regulator)
7. Door screen
Removal
Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-12
8. Front door glass
2. Inner garnish
9. Glass run channel
3. Front door trim (Manual window)
10. Manual window regulator
4. Front door trim (Power window)
11. Power window regulator
5. Inner handle
6. Sealing pad Inspectron . . . , . . . . . , . . . , . . . . . . . . . . . . . . . . . . . . .
page S-32
s-10

FRONT SIDE WINDOW REGULATOR AND GLASS
‘ROTEGk
(70-100 cm-kg,
81-87 in-lb)
(70-100 cm-kg,
81-87 in-lb)
0
1. Regulator handle (Manual regulator) 7. Door screen
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-12 8. Front door glass
2. Inner garnish 9. Glass run channel
3. Front door trim (Manual window) 10. Manual window regulator
4. Front door trim (Power window) 11. Power window regulator
5. Inner handle Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-32
6. Sealing pad
S-l 1

S FRONT SIDE WINDOW REGULATOR AND GLASS
SMCJOSX-01
Removal Note
Regulator handle
Remove the regulator handle installation clip with a rag as
shown in the figure.
s-12

FRONT DOOR LOCK AND OPENER S
FRONTDOORLOCKANDOPENER
COMPONENTS
Removal / Installation
1. Raise the front door glass fully to remove the door lock assembly.
2. Disconnect the negative battery cable.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal.
Caution
l Remove the door screen carefully so that it may be reused.
Note
l Refer to page S-56; Removal of the door mirror for removal of the inner garnish.
1ATCHBACK
1. Regulator handle (Manual regulator) 7. Door screen
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page S-12 8. Lock control (Power door lock)
2. Inner garnish 9. Front door lock assembly
3. Front door trim (Manual window) 10. Outer handle
4. Front door trim (Power window) 11. Lock cylinder retainer
5. Inner handle 12. Lock cylinder
6. Sealing pad
s-13

S
r
FRONT DOOR LOCK AND OPENER
- 1
PROTEGk
03uosx
1. Regulator handle (Manual regulator)
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page
2. Inner garnish
3. Front door trim (Manual window)
4. Front door trim (Power window) 5. Inner handle
6. Sealing pad 7.
Door screen S-12 8.
Lock control (Power door 9.
Front door lock assembly 10.
Outer handle 11.
Lock cylinder retainer 12.
Lock cylinder lock) .-,
S-l 4

REAR DOOR S
REAR DOOR
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
Note
l Remove the rear door trim and door screen for removal of the checker. (Refer to naae S-17.
N-m (m-kg, ft-lb)
1. Harness connector 5. Door lock striker
2. Checker pin Adjustment Note ,..............,.....,.,. page S-16
3. Hinge 6. Checker
4. Rear door
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . . . page S-i 6
S-l 5

S REAR DOOR
4 f 0.8 (0.16 f 0.03)
OR (FRONT)
-c1 A4 SEC.A-A
mm (in)
03uosx-0’
Adjustment Note
Door lock striker
1. Verify that the door can be closed easily and that there is
no looseness. If there is a problem, loosen the striker mount-
ing screws and adjust by moving the striker vertically or
laterally.
2. Check the rear offset of the door to the body. If there is a
problem, adjust it by moving the door lock striker laterally.
Tightening torque:
18-26 N.m (1.8-2.7 m-kg, 13-20 ft-lb)
Note
l Use a TORX drive bit for removal/installation of the
door lock striker.
Rear door
Loosen the hinge bolts and adjust as shown in the figure. Tight-
en the bolts to the specified torque.
Tightening torque:
18-29 N-m (1.8-3.0 m-kg, 13-22 ft-lb)
S-16