1992 MAZDA PROTEGE Workshop Manual

FUEL CUT CONTROL SYSTEM F
FUEL CUT CONTROL SYSTEM
DESCRIPTION
This system is used to improve the fuel economy, to prevent engine bucking during deceleration, and to
protect the engine from overspeeding.
23UOFX-127
PREPARATION
SST
r
49 9200 162
03UOFX.191
l7=---T II USE CPNNECTOR A
03UOFX-19
SYSTEM OPERATION
1. Connect a tachometer to the diagnosis connector IG-
terminal.
2. Connect the
SSTs (Engine Signal Monitor and Adapt-
er)
to the engine control unit (ECU).
3. Warm-up the engine to normal operating temperature and
run it at idle.
Warning
l Confirm that transmission is in Neutral (MTX) or P
range (ATX).
4.
Set the SST (Sheet) on the Engine Signal Monitor with
the specified side fancing up as shown.
Note
l MTX...48 PIN
l ATX...64 PIN
I 23UOFX-128
F-l 43

F FUEL
23UOFX-12:
0-6V
23UOFX- 131
to the terminal 2U or 2V (MTX), 3U or 3V (ATX)
hat the green and red lamps flash alternately.
nd No,3.....ECU terminal 2U (MTX)
3U (ATX)
. . . ..ECU terminal 2V (MTX)
3V (ATX)
6. Increase the engine speed to 4,000 rpm and then suddenly
release the throttle.
7. Verify that the red indicator lamp illuminates while the en-
gine speed is above approx.
1,900 rpm on deceleration.
t aced maximum rpm over 3 sec.
8. Increase the engine speed and verify that the maximum rpm
does not exceed specification.
.
.
. ..“.*..1”*“.-.“.....*......*...
Approx. 7,300 rpm
. . ..I......m....“.....*........m Approx. 6,300 rpm
F-l 44

DECHOKE CONTROL SYSTEM t-
DECHOKE CONTROL SYSTEM
DESCRIPTION
To facilitate starting the engine when the spark plugs become fouled, such as when the engine is flooded,
fuel injection is cut if the throttle valve is held wide open while cranking and the engine coolant temperature
is O°C (32OF) or below. This allows the spark oluas to drv and purges excess fuel from the cylinders.
f-- ECU _
. IGNITION SWITCH (START)
l ENGINE SPEED BELOW 500 rpm ’
l THROTTLE VALVE FULLY OPEN
l ENGINE COOLANT TEMPERATURE ;
BELOW
0% (32°F) I FUEL CUT
OBUOFX-19
I / / ‘ I
SYSTEM OPERATION
1.
2. Check if the engine coolant temperature is below O°C
(32OF).
If the engine coolant temperature is above O°C (32OF), dis-
connect the water thermosensor connector and connect an
approx. 10 kB resistor to the connector.
03UOFX.198 3. Turn the ignition switch to START and verify that the injec-
OBUOFX-19! 3
tor operating sound is heard.
4. Depress the accelerator pedal fully and turn the ignition
switch START. Verify that no injector operating sound is
heard.
F-l 45

F DECHOKE CONTROL SYSTEM
MEMO
.-,
F-l 46

CONTROL SYSTEM F
CONTROLSYSTEM
PREPARATION
SST
49 9200 162
Engine Signal
Monitor
49 HO18 9Al
Self-Diagnosis
Checker
49 GO1 8 904
Sheet For
inspection of
ECU
For
inspection of
oxygen sensor
For
inspection of
ECU 49 GO18 903
Adapter
harness
49 BO19 9AO
System
Selector For
inspection of
ECU
For
inspection of
oxygen sensor
03UOFX-20
F-l 47

F CONTROL SYSTEM
STRUCTURAL VIEW
23UOFX-1:
1. Engine control unit (ECU) 8. Solenoid valve (Pressure regulator control)
- .--
Removal / Installation . . . . . . . . . . . . . . . . page F-149
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page F-149
2. Circuit opening relay
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . page F-l 29
Inspection ,...,........................... page F-l 29
3. Clutch switch (MTX)
inspection . . . . . . . . . . . . . . . . . . . . . . . . . page F-l 72
4. Airflow meter (With intake air thermosensor)
Inspection .,..........,...,............... page F-l 68
5. ISC valve
Inspection .,*,........,.,.........,....... page F-116
Removal / Installation . . . . . . . . ,.... page F-l 09
G-Throttle sensor
Inspection . . . . . . . . . . . . , . . . . . . page F- 169
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . page F-l 09
7. Solenoid valve (VICS) [DOHC]
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page F-l 18 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. Water thermosensor
Inspection. . . . . . . .
Removal I Installation ....I..........
10. Solenoid valve(Purge control)
Inspection ,............ ,..................
11, Main relay (FUEL INJ relay)
Inspection. ..,............................
12. Neutral switch (MTX)
Inspection ,.,,,,....I.l,,.........I.......
Replacement . . . . . . .
13. Oxygen sensor
Inspection,. . . .
Replacement . , . . . .
14. P/S pressure switch
Inspection . . ..__.._._._........
Replacement . , . . . . . . . . . . . . . page t-135
page F-l 68
page F--l 68
page F-l 40
page F-172
page F-l 73
page F-173
page F-171
page F-172
--
page F-173
page F-173
F-l 48

CONTROL SYSTEM F
SMALL TYPE
03UOFX.20:
03UOFX-20
23UOFX-13
TERMINALS
AANDB
c “.w a ,.1/M rrmrrm
_-
03UOFX-201
ENGINE CONTROL UNIT (ECU)
Removal / Installation
1. Remove the side walls (driver’s side and passenger’s side).
(Refer to page S-94.)
2. Remove the bolts and nuts.
3. Disconnect the ECU connectors.
4. Install a
new ECU in the reverse order of removal.
Inspection
1. Disconnect the ECU connectors.
2. Connect the
SSTs (Engine Signal Monitor and Adapt-
er)
to the ECU as shown,
3. Set the SST (Sheet) on the Engine Signal Monitor with
the specified side fancing up as shown.
Note
l MTX...48 PIN
l ATX...84 PIN
4. Measure the voltage at each terminal.
(Refer to pages F-150 to F-167.)
5. If any ECU terminal voltage is incorrect, check the related
input or output devices and wiring. If no problem is found,
replace the ECU. (Refer to above.)
Caution
l Never apply voltage to SST terminals A and B.
F-l 49

CONTROL SYSTEM
Terminal voltage (MTX)
VB: Battery voltage
wminal Input Output Connection to Test condition Correct voltage Remark
1A - - Battery Constant VB For backup
1B 0 Main relay OFF OV
(FUEL INJ relay) Ignition switch ._-
ON VB
1c 0 Ignition switch While cranking Approx. 10V
(START) -
Ignition switch ON ov
10 0 Self-Diagnosis Test switch at “SELF-TEST” With Self-
Checker Lamp illuminated for 3 sec. after ignition 4.5--5.5v Diagnosis Check-
(Monitor lamp) switch OFF+ON er and System
Lamp not illuminated after 3 sec. VEI Selector
Test switch at “02 MONITOR” at idle
Monitor lamp illuminated 4.5-5.5v
Test switch at
“02 MONITOR” at idle
Monitor lamp not illuminated Va
1E 0 Malfunction indica- Lamp illuminated for 3 sec. after ignition
Below 2.5V With System
tor lamp (MIL) switch OFF-ON Selector test
Lamp not illuminated after 3 sec.
VB switch at
“SELF-TEST”
Lamp illuminated Below 2.5V
Lamp not illuminated VR
1F
0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2.5V
l With Self-
Checker switch OFF+ON Diagnosis
(Code Number)
Buzzer not sounded after 3 sec. VE - Checker and
Buzzer sounded Below 2.5V System Selector
l With System
Buzzer not sounded
VB Selector test
switch at
“SELF-TEST”
1G 0 Igniter Ignition switch ON ov
-
Idle Approx. 0.2V
1H - - - - - -
_-
II - - - - - -
1J
0 AIC relay Ignition switch ON
VB
A/C switch ON at idle Below 2.5V
A/C switch OFF at idle VB
-
1K 0 Diagnosis
connector
(TEN terminal) System Selector test switch at
“02 MONITOR”
System Selector test switch at
“SELF-TEST” VB
ov Ignition switch
ON
1L 0 DRL relay
(Canada) Parking brake pulled with ignition switch
Ve
l DRL.: Daytime
ON (DRL OFF) Running Lights
Idle (DRL ON) Below 2.5V
V’
F-l 50