1992 MAZDA PROTEGE Workshop Manual

S
HEADLINEF?
COMPONENTS
Removal / Installation
1, Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.
Note
l Remove the surroundina trlm for removal of the headliner. (Refer to pages S-97, 98.)
PROTEGii
(WITH PASSIVE SHOULDER BELT)
R.H. SIDE
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding
sunroof)
4. Sunvisor
S-89

S HEADLINER
Y
PROTEGfi
(WITHOUT PASSIVE SHOULDER BELT)
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding
sunroof)
4. Sunvisor
IJ”“DA-“oC
5. Sunvisor adapter
9. Headliner
6. Rearview mirror Removal Note . . page S-93
7. Overhead console (With slid- Installation Note page S-93
ing sunroof)
IO. Front top bracket
8. Seaming welt (Pillar)
s-90

HEADLINER S
HATCHBACK
(WITH
PASSIVE SHOULDER BELT)
I
R.H. SIDE I
1. Assist handle 5. Rearview mirror
2. Interior lamp 6. Headliner
3. Sunvisor Removal Note .,.,,.,,.......*........,.*.* page S-93
4. Sunvisor adapter
Installation Note ..,.............*......... page S-93
s-91

s HEADLINER
HATCHBACK
(WITHOUT PASSIVE SHOULDER BELT)
R.H. SIDE
1. Assist handle
2. Interior lamp
3. Seaming welt (With sliding sunroof)
4. Sunvisor
5. Sunvisor adapter
6. Rearview mirror
13uosx-03
7. Overhead console (With sliding sunroof)
8. Seaming welt (Pillar)
9. Headliner
Removal Note ,..........,,,....,..,....... page S-93
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . . page S-93
10. Front top bracket ---
S-92

HEADLINER S
iATCHE3ACK
A
3EC.A-A: WITHOUT PASSIVE SHOULDER BELT
03uosx-17
Removal Note
Headliner
The headliner is bonded to the front (or rear) top bracket with
the double adhesive tape as shown. (Except hatchback with
passive shoulder belt.)
Caution
l Peel off the bonded section of the headliner care-
fully to prevent damaging it.
Installation Note
Headliner
1. Install the headliner using the body brackets (hatchback)
and fasteners.
2. Install the seaming welt between the front top bracket and
the body to hold the headliner.
s-93

S DASHBOARD
DASHBOARD
COMPONENTS
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure, referring to
Removal Note.
3. Install in the reverse order of removal, referring to Installation Note.

DASHBOARD S
1, Rear ashtray (Without passive IO. Combination switch 18. Glove box lid
shoulder belt) Removal / Installation 19. Lower panel (R.H.)
2. Rear console ,..,,.,......,,.,.,....... Section T 20. Front ashtray
3. Front console 11. Center upper hole cover 21. Lower panel (Center)
4. Control box center cover 12. Upper garnish
22. Glove box cover
(With small front console) 13. Side panel 23. Dash board
5. Side walls 14. Hood release knob Removal Note . . page S-95
6. Undercover 15. Lower panel (L.H.) Installation Note page S-96
7. Steering column 16. Meter hood 24. Pipe frame (Lower)
Removal / Installation 17. Instrument cluster 25. Pipe frame (Upper)
. . . . . . . . ...*. . . . . ..n..... Section N Removal I Installation
1 suosx-017
8. Key cylinder set ring
9. Column cover
JOINT BOX
. . . . . . . . . . . . . . . . . . . . . . . . . . Section T
Removal Note
Dashboard
1, Remove the control wires of the heater unit and blower unit.
2. Disconnect the necessary harness connectors.
s-95

S DASHBOARD
03UOSX-182
03uosx-18 '3
Installation Note
Dashboard
After installing the dashboard, adjust the control wires of the
heater and blower units.
Mode control wire
1. Set the control lever to the position shown.
2. Set the mode control link to the extreme stop position.
Install the wire loop onto the link.
3. Clamp the wire into position with the clip.
Caution
l Move the Mode lever to verify that it moves the full
stroke between DEF and VENT.
Ret-Fresh selector control wire
1. Set the control lever to the position shown.
2. Set the air-mix control link to the extreme stop position.
Install the wire loop onto the link.
3. Clamp the wire into position with the clip.
Caution
l Move the Ret-Fresh lever to verify that it moves the
full stroke between REC and FRESH.
Temperature control
Temperature control wire
1. Set the control lever to the position shown.
2. Set the temperature control link to the extreme stop posi-
tion. Install the wire loop onto the link.
3. Clamp the wire into position with the clip.
Caution
l Move the Temperature control lever to verify that
it moves the full stroke between HOT and COLD.
S-96