1992 MAZDA PROTEGE Workshop Manual

RELAY
h f d
OWOTX-01;
OWOTX-01’
23UOTX-00
FLASHER UNIT
Inspection
1. Check for continuity between terminals of the flasher unit.
0: Indicates continuity X: No continuity
Note
l Set the tester to the xl,OOOQ range.
2. If continuity is not as specified, replace the switch.
DOOR LOCK TIMER UNIT
inspection
1. Check for continuity between terminals.
a-h X c-e 0 e-h 0
b-c X c-f 0 f-h X
0: Continuity X: Non-continuity
Note
l Set the tester to x1000Q range.
l Continuity includes the state with resistance, and
Non-continuity means insulated.
2. Connect the battery voltage to the “b” terminal and the
ground to the “a” terminal. Then, short circuit the “h” and
“d” terminals between the “h” and “c” terminals, and check
that the relay clicks.
T-17

T RELAY
23UOTX-01
d b
23UOTX-01 I
d b
23UOTX-0’
d b
ZNOTX-01
HORN RELAY
Inspection
1. Connect the battery voltage to the “d” terminal and the
ground to the “b” terminal. Check for continuity between
the “a” and “c” terminals.
HEADLIGHT RELAY
Inspection
1. Disconnect the headlight relay connector and remove the
relay.
2. Check for continuity between terminals of the relay.
Va: Battery voltage
Connecting to a b C d VB Ground
- -
0 cl
a b 0 0
O--O: Indicates continuity
TNS RELAY
Inspection
1. Disconnect the TNS relay connector and remove the relay.
2. Check for continuity between terminals of the relay. Ve: Battery voltage
4
Connecting to
a b C d VB Ground
- -
0 0
a b 0 0
O--O: Indicates continuity
DRL RELAY (CANADA)
Inspection
1. Disconnect the DRL relay connector and remove the relay.
2. Check for continuity between terminals of the relay. Ve: Battery voltage
lnnecting to
a b C d
V0 Ground
- -
0 0
a b 0 0
o---O: Indicates continuity
T-l 8

SWITCHES T
SWITCHES
STRUCTURAL VIEW
13UOfX-0'
1. Rear window defroster switch 6. Power window main switch
Inspection . . . . #. . . . . . . . . . . . . . . ..,. . . . . . . . . . . . page T-21 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
2. Remote control door mirror switch
7. Power window switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-20 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
3. Ignition switch
8. Cruise control switch
Removal I Installation . . . . . . . . . . . . . . . . . . page T-20 Removal / Installation . . . . . . . . . . page T-20
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21
4. Cruise control main switch 9. Combination switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 Removal / Installation . . . . . . . . . . pages T-23, 25
5. Hazard warning switch Disassem biy / Assembly . . . . . pages T-24, 26
Removal / Installation . . . . . . . . . . . . . . . . . . page T-20 Inspection ,...,.,.,.................. pages T-27, 28
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-21 10. Panel lamp control switch
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . .
page T-22
T-l 9

T SWITCHES
03UOTX-026
H&N CAP
03UOTX-02 8
03UOTX-02s
SWITCH
Removal / Installation
Ignition switch
1. Remove the negative battery cable.
2. Remove the steering column cover.
3. Remove the screw and the ignition switch.
4. Install in the reverse order of removal.
Hazard warning switch
1. Remove the meter hood.
2. Remove the screws and the hazard switch.
3. Install in the reverse order of removal.
Cruise control switch
(set/coast and resume/accel switch)
1. Remove the steering wheel cap.
2. Remove the cruise control switch as shown in the figure.
3. Install in the reverse order of removal.
Inspection
1. Check for continuity between the terminals with an
ohmmeter.
Remote control door mirror switch
CLASS DIRECTION a b c d i k I
UP o---o
0 0
1 UP
I I lo! I-l7ol
o----O: Indicates continuity
T-20

SWITCHES T
e C a
~ f
d b
03UOTX-03
13UOTX-OC
WARNING SW
03UOTX-0:
b a d
h
13UOTX-01
03UOTX-03
Rear window defroster switch
O----0: Indicates continuity
Ignition switch
O----0: Indicates continuity
Hazard warning switch
C--O: Indicates continuity
Cruise control main switch
I I OFF
I ON l% I I ,
G----O: Indicates continuity
2. Measure the switch resistance with an ohmmeter.
Cruise control switch
Switch Condition Check terminal
a-b
OFF
co
RESUMElACCEL
ON 910n
OFF Co SET/COAST ON 2400
o---O: Indicates continuity
T-21

T SWITCHES
03UOTX-03 i5
k i g f d
b
OBUOTX-0: $6
03UOTX-03
23UOTX-01
Power window main switch
(Power switch)
Terminal
Position a h
OFF
ON
0 0
C--O: indicates continuity
(Power window switch)
o---O: Indicates continuity
Power window switch (Each door)
Terminal
UP A B C D E
0 0
0 0
OFF 0 0
0 0
DOWN 0 0
0 0
m: Indicates continuity
Panel lamp control switch
1. Remove the switch.
2. Apply battery voltage to terminal ‘Id” and ground to termi-
nal “g”.
3. Check that the voltage at terminal “a” changes linearly when
turning the switch.
Switch
Min. position
Max. position Voltage
1ov
ov
T-22

SWITCHES T
COMBINATION SWITCH
Removal / Installation (Except Canada without cruise control system)
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
1. Horn cap
2. Steering wheel
3. Steering column cover 4. Combination switch
Disassembly I Assembly , . , . . . . . . . . . . page T-24
Inspection .,......,.,....,.*..*..,.,......... page T-27
T-23

T SWITCHES
USA WITHOUT CRUISE CONTROL SYSTEM
4
P
WITH CRUISE CONTROL SYSTEM
4
P
Disassembly / Assembly
1. Remove in the order shown in the figure.
2. install in the reverse order of removal.
6
1.
Cancel cam
2.
Spring
3. Slip ring assembly
1 WOTX-01
4. Wiper lever
5. Light unit
T-24