1992 MAZDA PROTEGE heating

E OUTLINE, TROUBLESHOOTING GUIDE
OUTLINE
SPECIFICATIONS
B6 SOHC
BP SOHC BP DOHC
MTX
1 ATX 1 MTX ATX 1 MTX
ATX
Cooling system
Water-cooled, forced circulation
Coolant capacity liters (US qt, Imp qt) 5.0 6.0
5.0
(5.3, 4.4) (6.3, 5.3)
(5.35.04.4) (6.zi.3) (5.3, 4.4) (6.::.3)
Water
pump
Thermostat
Radiator
Cooling fan
L Type
Water seal Centrifugal
Unified mechanical seal
Type Opening temperature
‘C (OF’) Wax, two-stage
Main: 86.5-89.5 (188-193)
Sub : 83.5-86.5 (182-188)
Full-open temperature
OC (OF)
Full-open lift mm (in)
Type
Cap valve opening
pressure 100 (212)
Main: 8.0 (0.31) min.
Sub : 1.5 (0.06) min.
Corrugated fin
74-103 (0.75-1.05, 11-15)
kPa (kg/cm2, psi)
Width
Core size Height
mm (in)
Depth
Fin pitch
mm (in) 647 (25.47)
390 (15.35)
16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98)
1.3 (0.051)
Heat dissipation capacity
kcallh 1 38,800 [ 43,800 ( 38,800 1 43,800 1 38,800 1 43,800 1
Type
Transaxle Heat
oil cooler dissipation
capacity
kcallh
Tvoe
- Laminated - Laminated -
Laminated
1,700
I .I -?nn
- -
I,,“”
I
I - I 4 Ye,-. I,IVV 1
, a-
- Electric
Number of blades 4
Outer diameter mm (in)
320 (12.6)
Capacity w-v 80-12 1 160-12 ) 80-12 ) 160-12 1 80-12 1 160-12
1 Hi: 13.3+ 1 1 Hi: 13.3+ 1 1 Hi: 13.3+
Current
TROUBLESHOOTING GUIDE I I I I
Problem Possible Cause
Overheating
Coolant level insufficient
Coolant leakage
Radiator fins clogged
Radiator cap malfunction
Cooling fan malfunction
Thermostat malfunction
Water passage clogged
Water puma malfunction .- Remedy Page
Add
Repair
Clean
Replace
Replace
Replace
Clean
Reolace E- 6
E-9
E- 7
E-13
E- 9
E- 6
E-11
I Corrosion
1 Impurities in coolant 1 Replace
I E-6 I
03UOEX-005

22 KNOCKING
DESCRIP- *Abnormal combustion accompanied by audible “pinging” noise
I-ION
[TROUBLESHOOTING HINTS]
3 Incorrect ignition timing (Too advanced)
@ Air/Fuel mixture too lean
3 Carbon deposits in cylinder
*Fuel injection amount not correct
3 Overheating
l Fuel line pressure decreases while accelerating
TEP INSPECTION
ACTION
1 Connect System Selector to diagnosis connector
Yes Go to next step
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up
CT page F-79
Ignition timing (BTDC)
l BP DOHC : go-1 1 o l BP SOHC : 4”-6O
’ B6 No
Adjust a page F-79
2 Check if “00” is displayed on Self-Diagnosis
Yes Go to next step
Checker with ignition switch ON
W page F-62
No
Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU w page F-149
W: SELF TEST c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check for correct intake manifold vacuum at idle
Yes Go to next step
VaCUUm: More than 450 mmHg (17.7 inHg) No
Check for air leakage of intake air sys-
tem components
4
Check for correct engine compression
Yes Go to next step
w page Bl-10
B2-10
Engine compression (Minimum):
l BP DOHC
883 kPa (9.0 kg/cm’, 128 psi)-300 rpm
l BP SOHC
834 kPa (8.5 kg/cm*, 121 psi)300 rpm
l B6
932 kPa (9.5 kg/cm’, 135 psi)300 rpm No High compression
Check engine condition CI page 81-10
62-l 0 l Carbon deposits
F-71

CHARGING SYSTEM G
RUB
PRO
03UOGX-01
Terminal and cable
1. Check the tightness of the terminals to ensure good electri-
cal connections.
2. Check for corroded or frayed battery cables.
3. Check the rubber protector on the positive terminal for prop-
er coverage.
4. Clean the terminals if necessary, and coat them with grease.
Recharging
Battery
55D23L Slow charge Quick charge
(A) (4
Under 6 Max. 20
Slow charging
It is not necessary to remove the vent caps to perform a slow
charge.
Quick charging
Remove the battery from the vehicle and remove the vent caps
to perform a quick charge.
Warning
l Before performing maintenance or recharging the
battery, turn off all accessories and stop the engine.
l The negative cable must be removed first and in-
stalled last.
l Set the battery in water when quick charging to pre-
vent overheating the battery.
G-9

S MOLDING, PROTECTOR, GARNISH
I 03UOSX-06
PRIMER 9
I
I 03uosx-070
BONDING AGENT
DOUBLE-SIDED ADHESIVE TAPE
03uosx-071
Installation Note
Protector
1. Use a knife to remove the adhesive remaining on the body
and protector.
Note
l Remove as much adhesive as possible without
damaging the painted surface.
l If the adhesive is difficult to remove, soften it with
a hot air blower.
2. Remove any grease or dirt from the protector and body
adhesion surface.
3. Apply primer to the protector as shown.
4. Attach double-sided adhesive tape to the protector (when
reused).
5. Apply adhesive (polyurethane) to the protector as shown.
6. Mark the installation position on the body with masking tape.
7. Align the protector on the body and attach it securely.
Note
l Adhesion conditions deteriorate if air temperature
is below 20°C (66OF); heating of the body is recom-
mended.
I 03UOSX-072
s-50