1992 MAZDA PROTEGE Workshop Manual

WINDSHIELD WIPER AND WASHER S
ALIGNMEhT MARK
23UOSX.023
MOLDING END FACE
!6-
1.10-1.26)
/ COWL GRILLE END FACE
mm (in
o3uosx-l2!
tATCHBACK
-L I COWL dRlLLE
mm (in:
03uosx-131
Removal Note / Installation Note
Wiper motor and bracket
1. Make an alignment mark on the bracket before removing
the motor arm from the motor.
2. Align the motor arm with the mark on the bracket when in-
stalling the arm.
Tightening torque:
1 l-18 N,m (1 lo-180 cm-kg, 95-158 in-lb)
Adjustment Note
Arm helght
1. Turn the wiper switch ON to operate the motor.
2. Turn the wiper switch OFF to set the automatic park position.
3. Set the arm height as shown in the figure.
Tightening torque:
9.8-14 N-m (100-140 cm-kg, 87-122 in-lb)
Washer nozzle
Insert a needle or similar object into the nozzle hole and move
the nozzle to adjust the spray direction.
s-73

S REAR WIPER AND WASHER
REAR WIPER AND WASHER
TROUBLESHOOTING GUIDE
Circuit Diagram
NEAR WIPER & WASHER
o-3
MAIN
JR-03 JB-06
REAR WASHER
._-.’

REAR WIPER AND WASHER S
Rear wiper does not operate
Check REAR WIPER 10A NG
= Repair harness and replace fuse
Turn ignition switch ON t
Check for battery voltage at terminal-wire (L/G) of rear NG
wiper motor connector Repair harness (Fuse-Rear wiper motor)
I
OK
I
Check for battery voltage at terminal-wire (L/B) of rear
wiper motor connector
I NG-
- Check rear wiper motor (Refer to page S-77)
OK
6
Remove the CPU
Check for battery voltage at B wire of the joint box (CPU) Repair harness (CPU-Rear wiper motor)
Check for OV at F wire of th Repair harness (CPU-Rear wiper switch)
Disconnect the rear wiper switch connector
Check for continuity of terminal-wire (B) to ground
I Repair harness (Rear wiper switch-Body ground)
OK
Check the rear wiper switch (Pi
Replace rear wiper switch
OK
- Replace CPU
J
23UOSX-025
Rear wiper automatic park function does not work t
Check continuity between rear wiper motor body and
ground Repair ground circuit of motor body
OK
Check rear wiper motor (Ref
I Replace rear wiper motor
23UOSX-026
s-75

REAR WIPER AND WASHER
Rear wiper does not stop when switch turned OFF
I -
Turn ignition switch ON and operate motor
I
Verify that wiper stops when connector disconnected
from rear wiper switch Check rear wiper switch (Refer to page S-77) NG
Disconnect connector from rear wiper motor;
check for no continuity of terminal-wire (L/B) of harness
side connector to ground Repair harness (Rear wiper motor-Rear wiper switch)
Check rear wiper motor (Re NG
Replace rear wiper motor
Replace CPU
23UOSX.027 Rear washer motor does not operate
(Rear wiper operates OK)
Check METER 15A fuse
Repair harness and replace fuse
Turn ignition switch ON
I
Check for battery voltage at terminal-wire (B/Y) of rear
NG
washer motor Repair harness (Fuse-Rear washer motor)
I
Check for battery voltage at terminal-wire (0) of rear
washer motor
t Check rear washer motor (Refer to page S-77)
1 OK
Check for battery voltage at terminal-wire (0) of rear
washer switch
I NG
_ Repair harness (Rear washer motor-Rear washer
switch)
Check rear washer switch (R
Replace rear washer switch
23UOSX.028
S-76

REAR WIPER AND WASHER S
23UOSX-02
b
I I 23UOSX-030
TYPE 1
TYPE 2 n
d
I I
23UOSX-031
REAR WIPER MOTOR
Inspection
Conductivity check
1. Disconnect the rear wiper motor connector.
2. Check for continuity between terminals (A) and (B) with an
ohmmeter.
Operation check
1. Check that the motor operates continuously when battery
voltage is connected to terminal (A) and a ground is con-
nected to terminal (B) of the motor.
2. Disconnect the ground from terminal (B) and immediately
connect it to the motor body. Verify that the motor shaft stops
at the park position.
3. If not as specified, replace the rear wiper motor.
REAR WASHER MOTOR
Inspection
1. Disconnect the rear washer motor connector.
2. Check for continuity between terminals (a) and (b) of the
washer motor with an ohmmeter.
3. Connect battery voltage to terminal (b) and ground termi-
nal (a) of the washer motor. Verify that the washer motor
operates.
4. If not as specified, replace the rear washer motor.
REAR WIPER AND WASHER SWITCH
Inspection
1. Disconnect the rear wiper and washer switch connector.
(Refer to Removal of combination switch; Section T.)
2. Check for continuity between terminals with an ohmmeter.
(Refer to; Section T.)
3. If not as specified, replace the combination switch.
s-77

S
COMPONENTS REAR WIPER AND WASHER
Removal / Installation
1. Disconnect the negative battery cable.
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
Note
l Refer to Section T for removal of the rear wiper and washer switch (in combination switch).
l Remove the rear portion of the headliner for removal of the rear washer nozzle.
(Refer to page Si91.)
r
6.9-9.8 N.m (70-100 cm-kg, 61-97 in-lb)
.9-9.8 N.m (60-100 cm-kg, W-87 In-lb)
2.9-5.9 N.m
(30-60 cm-kg,
v “L;/” 4.9-7.8.N.m
(SO-SO cm-kg, 4349 In-IL
S-78

REAR WIPER AND WASHER S
Wiper
Washer
1. Rear hatch lower trim
7. Trunk end trim
Removal / Installation . . . . . . . . . . . . . . . . page S-
98 Removal / Installation . . . . . . . . . . . . . . . . page
S- 98
2. Wiper arm cover 8. Trunk side cover
3. Rear wiper arm and blade Removal / Installation . . . . . . . . . . . . . . . . page S-
98
Adjustment
Note . . . . . . . . . . . . . . . . . . . . . . . page S- 79 9. Trunk side trim
4. Seal cap Removal / Installation . . . . . . . . . . . . . . . . page S-
98
5. Outer bushing 10. Rear header trim
6. Rear wiper motor Removal / Installation . . . . . . . . . . . . . . . . page S- 98
Inspection .,, ., . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 77 11. Rear seat belt upper anchor
Removal / Installation . . . . . . . . . . . . . . . . page S-l 01
12. C-pillar trim
Removal / Installation . . . . . . . . . . . . . . . . page S-
98
13. Washer tank assembly
a. Washer tank
b. Washer motor
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page S- 77
14. Washer nozzle
Adjustment Note . . . . . . . . . . . . . . . . . . . . . . . page S-
79
15. Washer pipe
23UOSX-032
REAR WINDOW MOLDING
mm (in)
03uosx-14
REAR WINDQW MOLDING I
mm (in
03uosx-14
Adjustment Note
Arm height
1. Set the motor shaft to the park position by turning the rear
wiper switch from ON to OFF.
2. Set the arm height as shown in the figure.
Tightening torque:
5.9-9.8 N*m (80-100 cm-kg, 52-87 in-lb)
Washer nozzle
Inset-t a needle or similar object into the nozzle hole and move
the nozzle to adjust the spray direction.
s-79

S SLIDING SUNROOF
SLIDING SUNROOF
TROUBLESHOOTING GUIDE
Circuit diagram
6LIDING SUNROOF M
MAIN
.Ol SLIDING SUNROOF M-02 SLIDING SUNROOF M-03 SLIDING SUNROOF M-04 SLIDING SUNROOF
(IN) SWITCH MOTOR RELAY
. ..&’
S-80
o3uosx-I 42