1992 MAZDA PROTEGE overheating

E OUTLINE, TROUBLESHOOTING GUIDE
OUTLINE
SPECIFICATIONS
B6 SOHC
BP SOHC BP DOHC
MTX
1 ATX 1 MTX ATX 1 MTX
ATX
Cooling system
Water-cooled, forced circulation
Coolant capacity liters (US qt, Imp qt) 5.0 6.0
5.0
(5.3, 4.4) (6.3, 5.3)
(5.35.04.4) (6.zi.3) (5.3, 4.4) (6.::.3)
Water
pump
Thermostat
Radiator
Cooling fan
L Type
Water seal Centrifugal
Unified mechanical seal
Type Opening temperature
‘C (OF’) Wax, two-stage
Main: 86.5-89.5 (188-193)
Sub : 83.5-86.5 (182-188)
Full-open temperature
OC (OF)
Full-open lift mm (in)
Type
Cap valve opening
pressure 100 (212)
Main: 8.0 (0.31) min.
Sub : 1.5 (0.06) min.
Corrugated fin
74-103 (0.75-1.05, 11-15)
kPa (kg/cm2, psi)
Width
Core size Height
mm (in)
Depth
Fin pitch
mm (in) 647 (25.47)
390 (15.35)
16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98) 1 16 (0.63) 1 25 (0.98)
1.3 (0.051)
Heat dissipation capacity
kcallh 1 38,800 [ 43,800 ( 38,800 1 43,800 1 38,800 1 43,800 1
Type
Transaxle Heat
oil cooler dissipation
capacity
kcallh
Tvoe
- Laminated - Laminated -
Laminated
1,700
I .I -?nn
- -
I,,“”
I
I - I 4 Ye,-. I,IVV 1
, a-
- Electric
Number of blades 4
Outer diameter mm (in)
320 (12.6)
Capacity w-v 80-12 1 160-12 ) 80-12 ) 160-12 1 80-12 1 160-12
1 Hi: 13.3+ 1 1 Hi: 13.3+ 1 1 Hi: 13.3+
Current
TROUBLESHOOTING GUIDE I I I I
Problem Possible Cause
Overheating
Coolant level insufficient
Coolant leakage
Radiator fins clogged
Radiator cap malfunction
Cooling fan malfunction
Thermostat malfunction
Water passage clogged
Water puma malfunction .- Remedy Page
Add
Repair
Clean
Replace
Replace
Replace
Clean
Reolace E- 6
E-9
E- 7
E-13
E- 9
E- 6
E-11
I Corrosion
1 Impurities in coolant 1 Replace
I E-6 I
03UOEX-005

22 KNOCKING
DESCRIP- *Abnormal combustion accompanied by audible “pinging” noise
I-ION
[TROUBLESHOOTING HINTS]
3 Incorrect ignition timing (Too advanced)
@ Air/Fuel mixture too lean
3 Carbon deposits in cylinder
*Fuel injection amount not correct
3 Overheating
l Fuel line pressure decreases while accelerating
TEP INSPECTION
ACTION
1 Connect System Selector to diagnosis connector
Yes Go to next step
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up
CT page F-79
Ignition timing (BTDC)
l BP DOHC : go-1 1 o l BP SOHC : 4”-6O
’ B6 No
Adjust a page F-79
2 Check if “00” is displayed on Self-Diagnosis
Yes Go to next step
Checker with ignition switch ON
W page F-62
No
Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU w page F-149
W: SELF TEST c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check for correct intake manifold vacuum at idle
Yes Go to next step
VaCUUm: More than 450 mmHg (17.7 inHg) No
Check for air leakage of intake air sys-
tem components
4
Check for correct engine compression
Yes Go to next step
w page Bl-10
B2-10
Engine compression (Minimum):
l BP DOHC
883 kPa (9.0 kg/cm’, 128 psi)-300 rpm
l BP SOHC
834 kPa (8.5 kg/cm*, 121 psi)300 rpm
l B6
932 kPa (9.5 kg/cm’, 135 psi)300 rpm No High compression
Check engine condition CI page 81-10
62-l 0 l Carbon deposits
F-71

CHARGING SYSTEM G
RUB
PRO
03UOGX-01
Terminal and cable
1. Check the tightness of the terminals to ensure good electri-
cal connections.
2. Check for corroded or frayed battery cables.
3. Check the rubber protector on the positive terminal for prop-
er coverage.
4. Clean the terminals if necessary, and coat them with grease.
Recharging
Battery
55D23L Slow charge Quick charge
(A) (4
Under 6 Max. 20
Slow charging
It is not necessary to remove the vent caps to perform a slow
charge.
Quick charging
Remove the battery from the vehicle and remove the vent caps
to perform a quick charge.
Warning
l Before performing maintenance or recharging the
battery, turn off all accessories and stop the engine.
l The negative cable must be removed first and in-
stalled last.
l Set the battery in water when quick charging to pre-
vent overheating the battery.
G-9