1967 CHEVROLET CAMARO Chassis Workshop Manual

CHASSIS SHEET METAL 11-10

Fig.
11 - Removing Spring with J-9559
Fig.
13- Hood,' Insulator, and Molding - Chevrolet

Fig.
14- Hood and Hood Ornament - Chevelle

Fig.
12 - Installing J-9559 in New Spring
Fig.
15 - Removing Rear Wheel Cover

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-11

CHEVY II

INDEX

Page

General Description 12

Maintenance and Adjustments 12

Hood ........ 13

Hinge 13

Bumpers 13

Catch Assembly . . . 13

Lock 13

Fenders . 13

Sheet Metal 13

Component Part Replacement 14
Page

Battery Tray 14

Radiator Support 14

Fender Assembly ...................... 14

Trim 15

Skirt 15

Hood Assembly 18

Catch Assembly and Lock • 18

Trim 18

Front End Assembly 18

1.
Fender

2.
Hood Hinge

3. Hood

4.
Trim

5. Molding
Fig.
16 - Front End Sheet Metal - Chevy II

6. Brace

7. Headlamp Filler Panel

8. Filler Panel

9. Radiator Support

10.
Shroud
11.
Radiator

12.
Skirt

13.
Hood Lock

14.
Hood Catch

15.
Baftery Tray

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-12

GENERAL DESCRIPTION

The sturdy front end structure is formed by three

welded assemblies, the left and right hand fender skirts

and the radiator support panel. These units are bolted

together and to the dash panel (fig.
16).

Fender skirts, containing spring towers and support

brackets for control arms, are welded to the reinforced

"closed hat section" side rails. The skirts and rails

are fastened at top and bottom to reinforced areas of the

dash panel. Each skirt and rail assembly is securely

mated ta the body with three bolts at the top, and at the

stub fr|.me butt plates with a four bolt series. Heavy

gauge, formed, reinforcing plates receive the top of the

fender skirt and provide a shimming surface for precise

alignment of front end and body when assembled.
The one-piece radiator support panel completes a box

section when welded to the front crossmember. The

panel is formed to add structural strength and rigidity.

This strong combination is bolted along the full length of

each forward vertical edge of the fender skirts and at

the stub frame ends. Additional strength is obtained from

rigid diagonal corner braces. These open hat section

braces, bolted to side rails and front crossmember,

provide mountings for the suspension tension struts.

Conventional front fenders, grille, bumper and brack-

ets all bolt on to the unit front end structure. The hood

is connected to the front end with hinges that are attached

to the fender skirts.

MAINTENANCE AND ADJUSTMENTS

" TO •/•"

Fig.
17 - Sheet Metd Adjustment - Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-13

HOOD ADJUSTMENT

The alignment of the hood in relation
to*
other sheet

metal parts is controlled by the position of the hood

hinges and the height of the two bumpers, located one at

each end of the radiator support. The adjustments at

the hood latch must be made after the hinges and bumpers

are positioned to yield the dimensions shown in Figure

17.
Latch adjustments are made so that effort required

to open and close the hood is reasonable, and hood align-

ment obtained by hinge and bumper adjustment is main-

tained when the hood is closed. Note that the hood latch

is not designed or intended to correct basic hood align-

ment faults.

To align the hood and lock, proceed as follows:

HOOD HINGE (Fig. 18)

1.
Note that the mounting holes in the body-mounted

end of the hinge are slotted to provide up and down

movement of the hood assembly while the hood

mounted end is slotted to provide fore and aft move-

ment.

2.
Scribe a mark around the entire hinge plate which

will be involved in the adjustment.

3.
Loosen the appropriate screws and shift the position

of the hood on the hinge plate the approximate amount

to correct misalignment, using the scribed marks to

check amount of movement. Check condition of ad-

justment by tightening cap screws and closing hood.

Fig.
18 - Hood Hinge - Chevy II
Fig.
19 - Hood Lock, Catch and Support - Chevy II

HOOD BUMPERS

Hood bumpers must be adjusted until hood and fender

line up as shown in Figure 17.

HOOD CATCH AND LOCK (Fig. 19)

Hood lock plate mounting holes are slotted to provide

fore and aft adjustment of the hood lock bolt. The hood

lock bolt itself is adjustable for up and down positioning

of the lock bolt head so that its proper engagement in the

latch assembly may be provided for. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood and so that the effort

required to release the hood catch is reasonable.

FENDER ADJUSTMENT (Figs. 17 and 20)

DO NOT CHANGE SKIRT ASSEMBLY-TO-DASH SHIM-

MING IN AN EFFORT TO ADJUST THE DOOR-TO-

FENDER GAP OR ANY OTHER SHEET METAL AP-

PEARANCE ITEM.

The front fenders are shimmed independently of the

skirt assemblies, unlike conventional- vehicles on which

almost the entire front end sheet metal assembly is

shimmed and adjusted as a unit.

Figure 20 shows the locations of front fender shims.

1.
The rocker panel extension location allows adjust-

ment to make fender outer surface flush with door

outer surface.

2.
The upper or plenum chamber location provides a

means of adjusting fender upper surface so that it

is flush with the upper surface of the cowl.

3.
The locations atop the skirt assembly are shimmed

to close the gap created between the fender mounting

flange and skirt assembly when the plenum chamber

CHEVROLET CHASSIS SWVICE MANUAL

CHASSIS SHEET METAL 11-14

location is shimmed; thus keeping the fender mount-

ing bolts from crushing in the fender mounting

flange.

If shimming is done without the fenders being disas-
asembled, it is suggested that fender mounting bolts

rearward of radiator support be loosened while shims

are inserted and sheet metal fit is checked. Tighten

shimmed mounting bolts first, then all others.

COMPONENT PART REPLACEMENT

BATTERY TRAY (FIG. 21)

Removal

1.
Disconnect battery cables.

2.
Remove screw retaining battery hold down clamp.

3.
Remove battery from vehicle.

4.
Remove screws retaining tray assembly to fender

skirt and support, and remove tray from vehicle.

Installation

Reverse removal procedure.

RADIATOR SUPPORT (FIG. 22)

Removal

1.
Remove grille and related components (Section 13).

Remove battery tray as outlined in this section.

Remove shroud attaching screws and remove shroud

if vehicle is so equipped.

Remove horn relay, horns, voltage regulator, and

wiring harness from radiator support.

Remove shroud and radiator (Section 13)o

Remove screws attaching radiator support to frame,

skirts,
fenders.

Remove radiator support from vehicle (fig. 23).

Installation

1.
Position radiator support in vehicle; align mounting

screw and bolt holes with drift punch.

Install screws and bolts loosely until all are started,

then tighten.

3.
Complete installation following removal procedure in

reverse order. Refer to torque specifications at rear

of manual for correct torque values.

4.
Aim headlamps as outlined in Section 12.

FRONT FENDER ASSEMBLY

Removal

1*
Remove headlamp dooro

2.
Open hood and remove screws joining fender top
2.

Fig. 20 - Front Fender Shimming
Fig.
21 - Battery Tray

flange to skirt. Remove, and record number of

shims at first cap screw forward of windshield (fig.

24).

3.
Remove screw located on upper surface of headlamp

cavity.

4.
From under forward end of fender, remove screw

retaining fender to radiator support.

5.
From inboard side of rocker panel extension, remove

cap screw retaining fender to extension. Remove,

and record number of shims.

6. Separate headlamp filler panel from fender by re-

moving remaining screws.

7.
Remove fender from vehicle.

Installation

1.
Inspect condition of cowl-to-fender seal and replace,

if necessary, as shown in Figure 25.

2.
Install headlamp filler panel on fender.

3.
Position fender on vehicle. Note that eowl-to-fender

seal must be positioned so that outer edge points

toward front of vehicle. Align all mounting screw

and bolt holes with drift punch and install all screws

and bolts loosely. Do not tighten any screws or bolts

until all are started. Refer to removal rocedure

for screw and bolt locations.

4.
Replace shims taken out when fender was removed

from vehicle and continue as outlined under Main-

tenance and Adjustments—Fender Adjustment.

5.
Install headlamp door and cheek headlamp aiming

as outlined in Section 12.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-15

FRONT FENDER TRIM

If fender spear molding is to be replaced without re-

moving fender from vehicle, proceed as follows:

1.
Perform Operations 2 and 5 only of Front Fender

Assembly—Removal.

2.
Pull rear* end of fender away from body far enough

to insert a short piece of 2 x 4 between lower rear

corner of fender and rocker panel extension.

3.
It should now be possible to gain access to first and

second retaining nuts forward of rear end of fender.

All other nuts can be reached from front wheel

opening.

SKIRT ASSEMBLY

Removal

1.
Remove hood and hinge assemblies as outlined in

this section.

2.
Remove grille and radiator support as outlined in

Section ia.

3.
Remove fender assembly as outlined in this section.

4.
Raise car from floor and place jack stands under

rocker panel extension.
5.
Remove suspension bumper support, shock absorber,

front spring and stabilizer link as outlined in Section

3.

6. If removing left skirt assembly, remove steering

gear mounting bolts, power steering hose clamp (if

so equipped) and outer (left) clutch cordon shaft

bracket (if so equipped).

7.
Remove tie rod ball stud from steering arm as out-

lined in Section 9.

8. Support engine and remove engine mount cushion as

outlined in Section 6.

9. Remove spring clip from brake line junction which

passes through skirt and remove junction from skirt

(see Section 5).

10.
Remove four bolts retaining front crossmember to

skirt.

11.
Remove four bolts retaining skirt assembly to dash

front brace. Remove 3 bolts retaining upper end of

skirt to dash (fig. 26); record shims removed.

12.
Remove skirt assembly with remaining suspension

parts attached as shown in Figure 27.

13.
Suspension parts may be detached as outlined in

Section 3.

Fig.
22 - Radiator Support Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-16

Fig. 23 - Removing Radiator Support from Vehicle

Inspection

If car has been involved in a collision it is advisable

to carefully inspect cowl and dash area for damage.

Check front of dash area following directions in Fisher

Body Manual. Pay particular attention to welds, cage

nuts,
weld nuts and skirt mounting surfaces. Cage and

weld nuts may be repaired by outright replacement (the

best method); or by the installation of spiral thread in-

serts.
If the spiral inserts are used, follow the instruc-

tions furnished by the manufacturer.

COWL
Fig. 25 - Replacing Fender Seal

Fig. 26 - Skirt Mounting Bolts

Fig. 24- Fender Mounts

Fig. 27 - Removing Skirt Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-17

Fig.
28- Hood Spring Removal

Installation

Skirt installation is written for the installation of a

stripped skirt, with suspension and otiier parts added

after skirt is attached to vehicle. Proceed as follows:

1.
Position skirt assembly on vehicle with insulator,

shown in Figure 26, in place and original shims in-

stalled at top dash mount

2.
Install the three bolts at top mount and four bolts at

lower dash brace.

3.
Install front crossmember, replacing the four bolts

and nuts removed previously.

4.
Replace engine mount cushion; refer to Section 6.

5.
Install front suspension parts as outlined in Sec-

tion 3. Connect stabilizer link to stabilizer (if so
FINAL POSITION

Fig.
30 - Installing Hood Molding Clip

equipped) and connect tie rod end to steering arm as

outlined in Section 9.

6. Install radiator support and fender assembly as out-

lined in this section. Install grille (Section 13).

7.
If left skirt was removed, proceed as follows:

a. Install steering gear. Carefully follow outline

under Steering Gear - Installation in Section 9.

Do not fail to perform adjustments listed under

Mast Jacket Installation in that section.

b.
Install clutch cordon shaft (if so equipped).

c. Install power steering hose clamp (if so equipped).

8. Install brake lines and bleed brakes as outlined in

Section 5.

9. Install hood and adjust as outlined in this section.

10.
Perform following checks and adjustments:

a. Check and adjust front body section alignment

as outlined in Fisher Body Service Manual.

Fig.
29 - Installing Tool J-9559 in Nev/Spring
Fig.
31 - Removing Front End Assembly from Vehicle

CHEVROLET CHASSIS SERVICE MANUAL