1967 CHEVROLET CAMARO Chassis Workshop Manual

STEERING
9-33

POWER STEERING

INDEX

Page

General Description
. 9-33

Maintenance
and
Adjustments
9-33

Bleeding Hydraulic System
9-33

Fluid Level
. 9-33

Adjustments
. 9-34

Power Steering Gear
. . 9-34

Pump Belt Tension
9-34
Hydraulic System Checks
9-34

Component Replacement
and
Repairs
. 9-35

Power Steering Pump.
. 9-35

Power Steering Gear
9-36

Control Valve
and
Adapter Assembly
9.35

Power Cylinder
9.37

Power Steering Hoses
9.39

GENERAL DESCRIPTION

Two types
of
power steering
are
used
for 1967.
One
is

the conventional linkage type
for
Chevy
n and
Corvette

vehicles
and the
other
is the
integral gear type
for

Chevrolet, Chevelle,
and
Camaro.
For
both types
the

hydraulic pressure
is
provided
by an
engine-driven vane-

type pump.

On
the
Chevy
n and
Corvette linkage type power steer-

ing, hydraulic pressure
is
delivered through
a
hose from

the pump
to a
valve which senses
the
requirement
for

power assistance
and
supplies
the
power cylinder
ac-

cordingly.
The
steering gear used with this power steer-

ing
is the
same basic unit used
on
manually steered

vehicles;
it is
serviced
as
outlined
in the
manual steering

part
of
this section except
for
adjustment, which
is

covered
in the
following pages.
The
steering linkage also

is serviced the same
as
manual counterparts.

The Chevrolet, Chevelle
and
Camaro integral gear type

power steering
has the
hydraulic pressure delivered

from
the
pump through two hoses
to the
steering gear.
In
the power steering gear
the
steering shaft, hydraulic

valve, worm, and rack-piston
nut are all in
line making
a

compact
and
space saving assembly.
All oil
passages
are

internal within
the
gear except
the
pressure
and
return

hoses.

The steering gear
is a
recirculating ball system
in

which steel balls
act as a
rolling thread between
the

steering worm
and
rack-piston
nut. The
rack-piston
nut

is
all one
piece
and is
geared
to the
sector
of
the piston

shaft.
The
valve
is
contained
in the
gear housing elimi-

nating
the
need
of
bolts
or
seals
to
attach
a
separate

valve housing.

The valve
is an
open-center, rotary-type three
way

valve.
The
spool
is
held
in
neutral position by means
of a

torsion
bar. The
spool
is
attached
by
means
of
the stub

shaft
to one end of the
torsion
bar
and
to the
valve body

on
the
other
end.
Twisting
of the
torsion bar allows
the

spool
to
move
in
relation
to the
valve body thereby oper-

ating
the
valve.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

1.
Fill
oil
reservoir
to
proper level and
let oil
remain

undistrubed
for at
least two minutes.

2.
Start engine
and run
only
for
about
two
seconds.

3.
Add
oil if
necessary.

4.
Repeat above procedure until
oil
level remains
con-

stant after running engine.

5. Raise front
end of
vehicle
so
that wheels
are off
the

ground.

6. Increase engine speed
to
approximately
1500 rpm.

7. Turn
the
wheels
(off
ground) right
and
left, lightly

contacting
the
wheel stops.

8. Add
oil if
necessary.

9. Lower
the car and
turn wheels right and left
on the

ground.

10.
Check
oil
level and refill
as
required.

11.
If oil is
extremely foamy, allow vehicle
to
stand
a

few minutes with engine
off and
repeat above

procedure.
,

a.
Check belt tightness
and
check
for a
bent
or
loose

pulley. (Pulley should
not
wobble with engine

running.)
b.
Check
to
make sure hoses
are not
touching
any

other parts
of the car,
particularly sheet metal.

c. Check
oil
level, filling
to
proper level
if
neces-

sary, following operations
1
through
10.
This

step
and
Step
"D" are
extremely important
as

low
oil
level and/or
air in the oil are the
most

frequent causes
of
objectionable pump noise.

d. Check
the
presence
of air in the oil. If air is

present, attempt
to
bleed system
as
described
in

operations
1
through
10. If it
becomes obvious

that
the
pump will
not
bleed after
a few
trials,

proceed
as
outlined under Hydraulic System

Checks.

FLUID
LEVEL

1.
Check
oil
level
in the
reservoir
by
checking
the dip

stick when
oil is at
operating temperature.
On

Chevelle models equipped with remote reservoir,

the reservoir should
be
maintained approximately

3/4 full when
oil is at
operating temperature.

2.
Fill,
if
necessary,
to
proper level with
GM
Power

Steering Fluid
or, if
this
is not
available, automatic

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-34

Fig.
64-Over Center Adjustment

transmission fluid "Type A" bearing the mark

"AQ-ATF" followed by a number and the suffix

letter "A".

ADJUSTMENTS

POWER STEERING GEAR

Chevrolet, Chevelle, and Camaro

The over-center adjustment (fig. 64) is the only power

steering gear adjustment which can be made on the car.

However, in order to make this adjustment, it is also

necessary to check the combined ball and thrust bearing

preload.

If the vehicle is equipped with a tilt column it will be

necessary to disconnect the steering coupling to obtain a

torque reading of the column. This torque should then be

subtracted from any reading taken on the gear.

1.
Disconnect the pitman arm from the relay rod.

2.
Loosen the pitman shaft adjusting screw loeknut and

thread the adjusting screw out to the limit of its

travel through the side cover. '. •

3.
Disconnect steering column harness at chassis wir-

ing connector plug.

4.
Remove horn button.

5.
Turn the steering wheel through its full travel, then

locate the wheel at its center of travel.

6. Gheck the combined ball and thrust bearing preload

with an inch-pound torque wrench on the steering

shaft nut by rotating through the center of travel

(approximately 1/4 turn in each direction). Note the

highest reading.

7.
Tighten the pitman shaft adjusting screw and check

torque at steering shaft nut until over center preload

and total steering gear preload falls within speci-

fications. Refer to torque specifications at rear of

manual for correct torque values.

8. Install horn button. Connect steering column harness

at wiring connector plug.
Chevy II and Corvette

The steering gear used with power steering is adjusted

in the same manner as the manual steering gear.

PUMP BELT TENSION

1.
Loosen nut on pivot bolt and pump brace adjusting

nut.

CAUTION: Do not move pump by prying against

reservoir or by pulling on filler neck.

2.
Move pump, with belt in place until belt is tensioned

to specifications as indicated by Tool J-7316 (Fig-.

65).

3.
Tighten pump brace adjusting nut. Then tighten pivot

bolt nut.

HYDRAULIC SYSTEM CHECKS

The following procedure outlines methods to identify

and isolate power steering hydraulic circuit difficulties.

This test is divided into two parts. Test number one

provides means of determining whether power steering

system hydraulic parts are actually faulty. If test number

one results in readings indicating faulty hydraulic opera-

tion, test number two will identify the faulty part. Be-

fore performing hydraulic circuit test, carefully check

belt tension and condition of driving pulley. Strand

tension of belt should be 125 lbs. on new belts and 75 lbs.

on old belts, as indicated by Tool J-7316 (Fig. 65).

Test Number One—Oil Circuit Open

Engine must be at normal operating temperature. In-

flate front, tires to correct pressure. All tests are made

with engine idling, so adjust engine idle speed to correct

specifications listed in Section 6 and proceed as follows:

a. With engine not running, disconnect flexible pres-

sure line from pump and install Tool J-5176 as

Fig.
65— Checking Belt Tension with Tool J-7316

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-35

Fig.
66—Power Steering Diagnosis

shown in Figure 66. Gauge must be between shut-

off valve and pump. Open shut-off valve,

b.
Remove filler cap from pump reservoir and check

fluid level. Fill pump reservoir to full mark on

dip stick. Start engine and, holding steering

wheel against stop, check connections at Tool

J-5176 for leakage. Bleed system as outlined
under Maintenance and Adjustments. Insert ther-

mometer (Tool J-5421) in reservoir filler open-

ing. Move steering wheel from stop to stop

several times until thermometer indicates that

hydraulic fluid in reservoir has reached tempera-

ture of 150° to 170°F.

CAUTION: To prevent scrubbing flat spots on

tires,
do not turn steering wheel more than five

times without rolling car to change tire-to-floor

contact area.

c. Hold steering wheel against a stop momentarily

and read pressure gauge. If the maximum pres-

sure is below specifications, a faulty hydraulic

circuit is indicated. To determine which part is

faulty, proceed with test number two.

Test Number Two—Oil Circuit Closed

a. Slowly turn shut-off valve on J-5176 to closed

position and read pressure indicated on gauge.

Quickly reopen valve to avoid pump damage, if

indicated pressure is less than specification,

pump output is below requirement and pump may

be considered faulty. If pressure indicated is

within specifications, it may be safely assumed

that the external hoses, connections, valve and

adapter or steering gear is at fault.

NOTE:
If pump proves faulty in test number

two,
test should be repeated after pump is re-

paired and installed in vehicle. This will provide

a means of checking the repairs made to the

pump and the condition of the steering gear or

valve and adapter which may also be faulty.

COMPONENT REPLACEMENT AND REPAIRS

POWER STEERING PUMP

Removal (Fig. 67)

1.
Disconnect hoses at pump. When hoses are discon-

nected, secure ends in raised position to prevent

drainage of oil. Cap or tape the ends of the hoses to

prevent entrance of dirt.

NOTE:
Chevelle with 396 engine uses a remote

reservoir. It is necessary to disconnect the

reservoir to pump hose before removing the

pump.
Hold a 1 qt. container under the reservoir

when the hose is removed to catch the fluid.

2.
Install two caps at pump fittings to prevent drainage

of oil from pump.

3.
Remove pump belt.

4.
On Corvette with 427 engine, loosen alternator ad-

justment and remove pump to alternator belt.

5. Remove pump from attaching parts and remove pump

from vehicle.

NOTE:
On Chevrolet and Chevy II equipped with

283 and 327 engine it may be necessary to re-

move pump brace.

6. Remove drive pulley attaching nut.

7. Remove pulley from shaft with Tool J-21239 (for

stamped pulleys) or Tool J-8433-1 with J-8433-2
adapter (for cast iron pulleys). Do not hammer

pulley off shaft as this will damage the pump.

Fig.
67—Power Steering Pump Mounting

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-36

Fig.
68—Power Steering Gear—Chevrolet Shown

Installation

1.
Install pump pulley.

CAUTION: Do not hammer on pump shaft. Use

pulley nut to pull pulley on to shaft.

2.
Position pump assembly on vehicle (Fig. 67) and in-

stall attaching parts loosely.

3.
Connect and tighten hose fittings.

4.
Fill reservoir. Bleed pump by turning pulley back-

ward (counterclockwise as viewed from front) until

air bubbles cease to appear.

5. Install pump belt over pulley.

6. Tension belt as outlined under "Pump Belt Tension

Adjustment" in this section.

7. Bleed as outlined under "Maintenance and

Adjustments."

POWER STEERING GEAR (Fig. 68)

Chevrolet,
Chevelfe,
and Comoro

Replacement procedures for the power steering gear

are the same as for the manual type steering gear.
•
Refer

to steering gear procedures near the beginning of this

section under "Component Replacement and Repairs".
In addition, disconnect pressure and return hoses from

the steering gear housing. Cap both hoses and steering

gear outlets to prevent foreign material from entering

the system. After service is performed and steering gear

is installed, connect the pressure and return hoses to

the steering gear housing. Bleed system as outlined

under Maintenance and Adjustment in this section. Refer

to torque specifications at rear of manual for correct

torque values.

CONTROL VALVE AND ADAPTER ASSEMBLY

Chevy II and Corvette

Ball Stud Seal Replacement (Fig. 69)

A ball stud seal is used on the power steering control

valve. To replace the seal:

1.
Remove the pitman arm as outlined under "Steering

Linkage" in this section.

2.
Remove clamp by removing nut, bolt and spacer or,

if crimped type clamp is used, straighten clamp end

and pull clamp and seal off end of stud.

3.
Install new seal and clamp over stud so lips on seal

mate with clamp. (A nut and bolt attachment type

clamp replaces the crimped type for service.)

CHEVROLET CHASSIS
SERVICE
MANUAL

STEERING 9-37

NUT

Fig.
69—Control Valve Ball Stud Seal Replacement

(Service Type)

4.
Center the ball stud, seal and clamp at opening in

adapter housing, then install spacer, bolt and nut.

Removal

1.
Raise the front of the vehicle off the floor and place

it on stands.

2.
Remove the relay rod to control valve clamp bolt.

3.
Disconnect the two pump to control valve hose cdn-

nections and allow fluid to drain into a container,
then disconnect the two remaining valve to power

cylinder hoses.

4.
Remove the retaining nut from the ball stud to pitman

arm connection and disconnect the control valve

from the pitman arm.

5. Turn the pitman arm to the right clear of the control

valve and unscrew the control valve from the relay

rod.

6. Remove the control valve from the vehicle.

Installation

1.
Install the control valve on the vehicle by reversing

the removal procedure.

2.
Reconnect the hydraulic lines, fill the system with

fluid and bleed out air using the procedure outlined

under "Maintenance and Adjustments/' Grease ball

joint.

POWER CYLINDER (Fig. 70)

Chevy II and Corvette

Removal

1.
Disconnect the two hydraulic lines connected to the

power cylinder and drain fluid into a container. Do

not reuse.

2.
Remove cotter pin, nut, retainer and grommet from

power cylinder rod attached to the frame bracket.

3.
Also remove grommet and retainer from bracket if

replacement parts are required.

1.
Snap Ring

2.
End Plug and

Lube Fitting

3.
"O" Ring
Fig.
70—Power Cylinder—Exploded View

4.
Spring

5. Spring Seat

6. Ball Stud
7. Ball Seat

8. Ball Stud Seal

9. Piston Body
10.
Piston Rod Seal

11.
Backup Washer

•12.
Scraper Element
13.
Piston Rod Scraper

14.
Snap Ring

15.
Piston Rod

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-38

CHEVROLET

CHEVELLE

CAMARO

Fig.
71—Power Steering Hose Installation

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-39

4.
Remove cotter pin, nut and ball stud at relay rod.

5. Remove the power cylinder from the vehicle.

Inspection

1.
Inspect the seals for leaks; if leaks are present,

replace the seals using the procedure outlined under

"Disassembly."

2.
Examine the brass fitted hose connection seats for

cracks or damage and replace if necessary.

3.
For service other than ball seat or seal replacement

and ball stud removal, replace the power cylinder.

4.
Check the frame bracket parts for wear.

Disassembly

1.
To remove the piston rod seal remove the snap ring;

then pull out on the rod, being careful not to spray

oil.

2.
Remove the piston rod scraper and scraper element,

back up washer and piston rod seal from the rod.

3.
At the ball stud end of the cylinder, remove the ball

stud seal.

4.
Remove the snap ring retaining the end plug with the

lube fitting.

5. Push on the end of the ball stud and remove the end

plug, spring, spring seat and ball stud.

6. Remove the "O" ring seal from the top lip of the

power cylinder ball stud opening.

7. If the ball seat is to be replaced, it must be pressed

out using Tool J-8937.

Assembly

1.
Reassemble the piston rod seal components by re-

versing the disassembly procedure. Apply a thin
coat of Lubriplate or equivalent on the inner sur-

faces of the seal and scraper before assembly.

2.
Reverse the disassembly procedure when reassem-

bling the ball stud.

3.
In each case be sure that the snap ring is securely,

seated in the ring groove.

Installation

1.
Install the power cylinder on the vehicle by reversing

the removal procedure.

2.
Reconnect the two hydraulic lines, fill the system

with fluid and bleed out air using the procedure out-

lined under "Maintenance and Adjustments." Grease

ball joint.

POWER STEERING HOSES

When servicing the power steering hoses be sure to

align the hoses in their correct position as shown in

Figure 71. On Chevelle models with 396 engine, install

the upper hose so that there is at least .6 inch clearance

between the hose and the Delcotron or the inner fender

skirt.

It is important that the power steering hoses be in-

stalled correctly. Hoses installed out of position may be

subjected to chafing or other abuses during sharp turns.

Always make hose installations with front wheels in

straight ahead position. Do not twist hoses unneces-

sarily during installation.

CAUTION: Do not start engine with any power

steering hose disconnected.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-40

SPECIAL TOOLS

1.
J-22572 Steering Column Bearing

Installer

2.
J-8937 Power Piston Ball Seat

Installer

3. J-6632 Pitman Arm Puller

4.
J-5178 Pull Gauge

5. J-2927 Steering Wheel Puller

6. J-21486 Actuator Cover Remover

7. J-6585 Slide Hammer

8. J-22599 Lock Nut Wrench

9. J-21854 Pivot Pin Remover
Fig.
72—Special Tools

10.
J-22549 Shift Tube Installer

11.
J-22551 Shift Tube Remover

12.
J-5421 Thermometer

13.
J-22635 Locking Shoe Guide Pin

and Release Lever Pin

Remover and Installer

14.
J-7754 Inch Pound Torque

Wrench

15.
J-22569 Snap Ring Remover and

Installer
16.
J-2185'3

17.
J-22568

18.
J-22670

19.
J-22686

20.
J-8433

21.
J-21239

22.
J-22573

23.
J-7316

24.
J-5176
Actuator Cover Installer

Spanner Wrench

Pump Main Shaft Seal

Installer

End Play Gauge

Pump Pulley Remover

Pump Pulley Remover

Column Support Fixture

Belt Tension Gauge

Pressure Gauge

CHEVROLET CHASSIS SERVICE MANUAL