1967 CHEVROLET CAMARO Chassis Workshop Manual

BRAKES 5-16

6Y. Adjust clutch pedal travel as outlined in

Section 7.

SHOES AND LININGS

Organic Linings

NOTE:
If brake drums are worn severely, it

may be necessary to retract the adjusting screw.

To gain access to the adjusting screw star

wheel, knock out the lanced area in the web of

the brake drum using a chisel or similar tool.

Release the actuator from the star wheel by

lifting with a small screw driver and back off

the star wheel with a second screw driver (press

down on the handle to retract shoes).

CAUTION: After knocking out the metal, be

sure to remove it from the inside of the drum .

and clean all metal from the brake compartment.

A new hole cover must be installed when drum

is reinstalled.

Removal

1.
Raise the vehicle and plate on jack stands.

2.
Loosen check nuts at parking brake equalizer suffi-

ciently to remove, all tension from brake cable.

3.
Remove brake drums.

NOTE:
Since there are wheel cylinder piston

stops to prevent pistons from leaving cylinders,

it is not necessary to install wheel cylinder

clamps when brake shoes are removed; however,

brake pedal must not be depressed while drums

are removed.

4.
Unhook brake shoe pull back springs from anchor

pin and link end, using Tool J-8049 (fig. 27).

5. Remove the actuator return spring and link.

6. Remove hold-down pins and springs (fig. 28).

7. Remove the actuator assembly.
NOTE:
The actuator, pivot and override spring

are an assembly. It is not recommended that

they be disassembled for service purposes,

unless they are broken. It is much easier to

assemble and disassemble the brakes by leaving

them intact.

8. Separate the brake shoes by removing adjusting

screw and spring.

9. Remove parking brake lever from secondary brake

shoe (rear only).

Inspection

1.
Clean all dirt out of brake drum using care to avoid

getting dirt into front wheel bearings. Inspect drums

for roughness, scoring or out-of-round. Replace or

recondition drums as required.

2.
Inspect wheel bearings and oil seal, and replace

any necessary parts.

3.
On Chevrolet only:

Carefully pull lower edges of wheel cylinder boots

away from cylinders and note whether interior is

wet with brake fluid. Excessive fluid at this point

indicates leakage past piston cups and a need for

wheel cylinder overhaul or replacement.

NOTE:
A slight amount of fluid is nearly always

present and acts as lubricant for the piston.

4.
Check cylinders with internal boots by carefully pull-

ing a small part of the boot out of the cylinder.

Note whether interior is wet with brake fluid. Ex-

cessive fluid at this point indicates leakage past

piston cups and a need for wheel cylinder overhaul

or replacement.

5. Check all brake flange plate attaching bolts to make

sure that they are tight. Clean all rust and dirt

from shoe contact faces on flange plate (fig. 29),

using fine emery cloth.

Installation

CAUTION: Make certain to install recom-

Fig.
27-Unhooking Pull Back Spring
Fig.
28—Removing Hold-Down Springs and Pins

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-17

mended shoe and lining assemblies. Otherwise,

serious fade or failure may occur.

1.
Inspect new linings and make certain there are no

nicks or burrs on bonding material on shoe edge

where contact is made with brake flange plate or

on any of the contact surfaces.

NOTE: Keep hands clean while handling brake

shoes.
Do not permit oil or grease to come in

contact with linings.

2.
If working on rear brakes, lubricate parking brake

cable.

3.
On rear brakes only, lubricate fulcrum end of park-

ing brake lever and the bolt with brake lube, then

attach lever to secondary shoe with bolt, spring

washer, lock washer and nut. Make sure that lever

moves freely.

4.
Before installation make certain the adjusting screw

is clean and lubricated properly.

NOTE: Loose adjustment may occur from an

adjusting screw that is not properly operating.

If the lubrication in the adjusting screw as-

sembly is contaminated or destroyed, the ad-

justing screw should be thoroughly cleaned and

lubricated.

5.
Connect brake shoes together with adjusting screw

spring, then place adjusting screw, socket and nut

in position.

CAUTION: Make sure the proper adjusting

screw is used ("L" for left side of vehicle,

"R"
for right side of vehicle). The star wheel

should only be installed with the star wheel

nearest to the secondary shoe and the adjusting

screw spring inserted to prevent interference

with the star wheel.
6. On rear wheels connect parking brake cable to lever.

7.
Secure the primary brake shoe (short lining—faces

forward) first with the hold-down pin and spring

using a pair of pliers. Engages shoes with the wheel

cylinder connecting links.

8. Install and secure the actuator assembly and second-

ary brake shoe with the hold-down pin and spring

using a pair of needle nose pliers. On rear wheels

position parking brake strut and strut spring.

9. Install guide plate over anchor pin.

10.
Install the wire link.

NOTE: Do not hook the wire link over the

anchor pin stud with the regular spring hook

tool. This may damage the cylinder boot seals.

Fasten the wire link to the actuator assembly ;

first, then place over the anchor pin stud by

hand while holding the adjuster assembly in the

full down position.

11.
Install actuator return spring.

NOTE: Do not pry actuator lever to install re-

turn spring. Ease it in place using the end of a

screw driver or other suitable flat tool.

12.
If old brake pull back (return) springs are nicked,

distorted or if strength is doubtful, install new

springs.

13.
Hook springs in shoes using Tool J-8049 by in-

stalling the primary spring from the shoe over the

anchor pin and then spring from secondary shoe

over the wire link end.

14.
Pry shoes away from backing plate and lubricate

shoe contact surfaces with a thin coating of brake

lube (fig. 29).

CAUTION:

facings.
Be careful to keep lubricant off

Fig.
29—Backing Plate Contact Surfaces
15.
After completing installation, make certain the actu-

ator lever functions easily by hand operating the

self-adjusting feature (fig. 30).

1.6. Follow the above procedure for all wheels.

17.
Adjust the service brakes and parking brake as

outlined under "Maintenance and Adjustments" in

this section.

Metallic Linings

Metallic brake linings which use special heat resistant

brake springs are available as an option. Service opera-

tions are the same as for standard brakes; however,

when new linings are installed, the linings should be

seated as described below.

NOTE: Brake shoes with metallic linings re-

quire specially finished brake drums (honed to a

20 micro-inch finish). Metallic linings are not

recommended for service replacement on ve-

hicles with standard brake drums that have not

been honed to specified finish.

Seating Metallic Linings

After the brakes have been adjusted, the following

recommended "lining seating" is as follows:

1.
Make six to eight stops from 30 MPH with moderate

pedal pressure to aid in seating and to mbdulate

any tendency to dive.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-18

Fig.
30—Checking
Operation
of the
Actuating
Lever
2.
Make six to eight complete stops from maximum

legal highway speed at approximately one mile inter-

vals to fully seat the linings.

Identification of Worn Lining (Fig. 31)

The metallic shoe assembly incorporates a number of

segmented pads with each pad consisting of two layers of

dissimilar material. The top layer is the braking ma-

terial and the lower layer is a metal bonding agent used

to weld the brake facing material to the shoe proper.

During brake inspection, one can be misled easily

since the bonding pad does not appear to be much dif-

ferent from the brake facing pad.

Close inspection of the shoes, however, will indicate

the difference between a worn and satisfactory shoe.

When the bonding pad begins to appear through the brake

facing material a bright finish will appear (fig. 31).

To preclude the possibility of excessively worn shoes

damaging the drum, it is recommended that metallic

brake shoes be replaced whenever segment thickness

becomes less than 3/32" measured at the heel or toe

of the pad.

MAIN CYLINDER

When servicing the Delco Moraine dual master cyl-

inder, follow the rules below when replacing either

complete master cylinder or the component pistons of

the cylinder. It is equally important to use 'only the

NORMAL

WORN

EXCESSIVELY
WORN

BRAKE

SHOE
PAD PART

'OF SHOE

•FACING

MINIMUM

•SERVICEABLE

LINING
%2
BRAKE

SHOE
PAD PART

OF SHOE

FACING
BRAKE

SHOE
PAD PART

OF SHOE

FACING

SEC
A-A

SEC
B-B

SEC
C-C

Fig. 31—Identification of Worn Metallic Brake Lining

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-19

correct service parts when servicing a Bendix main

cylinder.

1.
The two-letter identification stamp on the end of

the master cylinder indicates the displacement capa-

bilities of that particular cylinder. Master cylinders

should only be replaced with another cylinder bearing

the same two-letter identification.

2.
The length of the component pistons in the master

cylinders are critical factors in displacement capa-

bilities of a particular master cylinder. These

pistons are coded, using rings or grooves in the

shank of the piston. It is mandatory that when
pistons are replaced, the replacing piston must con-

tain the same identification marks and the same

contour at the push rod end as the piston which

is removed.

Delco Moraine dual master cylinders, used with

drum-type brakes, contain a rubber check valve and

check valve spring in each outlet boss. When the

car is equipped with disc brakes on the front and

drum brakes on the rear, the dual master cylinder

will have a check valve and spring in the outlet

boss for the rear brakes. No check valve is required

for four wheel disc brakes, and, therefore, the outlet

1.
Spring

2.
Check Valve

3. Valve Seat

4.
Bleeder Valve

5. Bail Wire

6. Cover

7. Diaphragm

8. Stop Screw

9. Body
Fig.
32-Main Cylinder for Drum Type Brakes-Exploded View

10.
Spring

11.
Retainer

12.
Seal

13.
Seal Protector

14.
Primary Piston

15.
Seal

16.
Seal

17.
Piston Extension Screw
18.
Secondary Piston Stop

19.
Spring

20.
Spring Retainer

21.
Seal

22.
Seal Protector

23.
Secondary Piston

24.
Seal

25.
Retaining Ring

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-20

boss to the front brakes will not contain a check

valve and spring. .

Removal

1.
Wipe main cylinder and lines clean with a clean

cloth. Place dry cloths below main cylinder area to

absorb any fluid spillage.

2.
Disconnect hydraulic lines at main cylinder. Cover

line ends with clean lint-free material to prevent

foreign matter from entering the system.

3.
Disconnect the push rod from the brake pedal.

4.
Unbolt and remove the main cylinder from the

firewall.

5.
Remove the main cylinder mounting gasket and boot.

6. Remove the main cylinder cover and dump out the

fluid. Pump the remaining fluid from the cylinder

by depressing the push rod.

Disassembly (Fig. 32)

1.
Clamp main cylinder in a bench vice.

2.
Remove push rod retainer.

3.
Remove secondary piston stop bolt from bottom of

front fluid reservoir.

4.
Remove the snap ring retainer and primary piston

assembly. Remove the secondary piston, piston

spring, and retainer by blowing air through the stop

bolt hole. (If no air is available, a piece of wire

may be used. Bend approximately 1/4 inch of one

end into -a right angle, hook the secondary piston

and pull it out.)

5.
Position main cylinder in vice with outlet holes

facing up.

6. Drill a 13/64 inch hole through both check valve

seats.

7 Tap out both seats using a 1/4 - 20 tap.

8. Install a spare brake line tube nut in the outlet

hole.
Place a flat washer on a one inch screw

(threaded to screw into tapped hole), and thread

screw into threaded hole in tube seat. Hold the

screw to keep it from turning and back out the

tube nut. This will remove the tube seat.

9. Repeat Step 8 above on second tube seat.

10.
Remove the check valves and springs from the cavi-

ties beneath the tube seats.

11.
Remove the primary seal, primary seal protector,

and secondary seals from the secondary piston.

Remove the piston extension screw securing the

primary piston spring to the primary piston. Re-

move the spring retainer, primary seal, primary

seal protector, and secondary seal from the pri-

mary piston.

Cleaning and Inspection

1.
Remove main cylinder casting from vice and inspect

the bore for corrosion, pits, and foreign matter.

Be sure that the outlet ports are clean and free of

brass cuttings from the tube seat removal operation.

2.
Inspect the fluid reservoirs for foreign matter.

Check the bypass and compensating ports to the

cylinder bore to insure that they are not restricted.

Do not use wire to check ports.

NOTE: Before washing parts, hands must be

clean. Do not wash hands in gasoline or oil

before cleaning parts. Use soap and water only.

3.
Use Declene or equivalent to clean all metal parts

thoroughly. Immerse parts in the cleaning fluid and
brush with hair brush to remove foreign matter.

Blow out all passages, orifices, and valve holes. Air

dry the parts and place on clean paper or lint-free

clean cloth.

NOTE: Be sure to keep parts clean until re-

assembly. Rewash parts, if there is any occa-

sion to doubt cleanliness.

4.
Check pistons for scratches or other visual damage;

replace if necessary.

Assembly (Fig. 32)

Use care when reassembling the main cylinder check

valves. Improper assembly of the check valve seats

will result in distortion of the seats. If this occurs,

there will be no check valve action and a loss of brake

pedal travel will result; the pedal will have to be pumped

one or more times before actual car braking occurs.

1.
Place the main cylinder in a vice with the outlet

holes facing up. Place the check valve springs, in

the outlet holes. Be sure the springs are seated

in the bottom of the holes. Place new rubber check

valves over the springs, being careful not to dis-

place the springs from the spring seats.

2.
Place new brass tube seats in the outlet holes. Be

sure seats are not cocked as this would cause burrs

to be turned up as the tube seats are pressed in.

. Thread a spare brake line tube nut into the outlet

hole and turn the nut down until the tube seat bot-

toms.
Remove the tube nut and check the outlet hole

for loose burrs, which might have been turned up

when the tube seat was pressed down. Repeat this

process to bottom the second seat.

3.
Put new secondary seals in the two grooves in the

end of the secondary piston assembly. The seal

which is nearest the end will have its lips facing

toward that end. The seal in the second groove

should have its lips facing toward the portion of

the secondary piston which contains the small com-

pensating holes.

4.
Assemble a new primary seal protector and primary

seal over the end of the secondary piston with the

flat side of the seal seats against the seal protector,

and the protector against the flange of the piston

which contains the small compensating holes.

5.
Assemble the new secondary seal into the groove on

the push rod end of the primary piston. The lips of

this seal should face toward the small compensating

holes in the opposite end of the primary piston.

6. Assemble the new primary seal protector and pri-

mary seal on the end of-the primary piston with the

flat side of the. seal seated against the seal protector,

and the protector against the flange on the piston

which contains the compensating holes.

7.
Assemble the spring retainer in one end of the

primary piston spring and the secondary piston

stop in the other end. Place the end of the spring

over the end of the primary piston with the spring

retainer seats inside of the lips of the primary

seal.

8. Remove all cleaning liquid from the threaded hole

in the primary piston. Place the piston extension

screw down through the secondary piston stop and

the primary spring retainer and screw it into the

primary piston until it bottoms out.

9. Coat the bore of the master cylinder with clean

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-21

brake fluid. Coat the primary and secondary seals

on the secondary piston with clean brake fluid. Insert

the secondary piston spring retainer into the sec-

ondary piston spring. Place the retainer and spring

down over the end of the secondary piston until the

retainer locates inside of the lips of the primary

cup.

10.
Hold the master cylinder with the open end of the

bore down. Push the secondary piston into the bore

until the spring seats against the closed end of the

bore.

11.
Position the master cylinder in a vise with the

open end of the bore up. Coat the primary and

secondary seal on the primary piston with clean

brake fluid. Push the primary piston assembly,

spring end first, into the bore of the master cylinder*

Hold the piston down and snap the lock ring into

position in the small groove in the I.D. of the bore.

12.
Push the primary piston down to move the secondary

piston forward far enough to clear the stop screw

hole in the bottom of the front fluid reservoir. Install

the stop screw.

13.
Install reservoir diaphragm in the reservoir cover

and install the cover on the main cylinder. Push

bail wire into position to secure the reservoir cover.

Installation

1.
Assemble the push rod through the push rod retainer,

if it has been disassembled.

2.
Push the retainer over the end of the main cylinder.

Assemble new boot over push rod and press it down

over the push rod retainer. Slide new mounting

gasket into position.

3.
Secure .the main cylinder to the firewall with mount-

ing bolts.

4.
Connect the push rod clevis to the brake pedal with

pin and retainer.

5. Connect the brake lines to the main cylinder.

6. Fill the main cylinder reservoirs to the levels

shown in Figure 8. Bleed the brake system as out-

lined in this section.

7. K necessary, adjust the brake pedal free play as

outlined in this section.

WHEEL CYLINDER (Fig. 33)

The wheel cylinder boots should be removed from a

cylinder body only when they are visibly damaged or

leaking fluid. Wheel cylinders having torn, cut, or heat-

cracked boots should be completely overhauled.

Removal

1.
Raise vehicle and place on jack stands.

Fig.
33-Chevelle Wheel Cylinder—Exploded View

1.
Push Rod Boot 6. Spring

2.
Piston 7. Piston Cup

3. Piston Cup 8. Piston

4.
Housing 9. Push Rod Boot

5. Fluid Inlet
2.
Remove wheel and tire assembly. Back off brake

adjustment, if necessary, and remove drum.

3.
Disconnect brake system hydraulic line from

cylinder.

4.
Remove brake shoe pull back springs.

5. Remove screws securing wheel cylinder to flange

plate. Disengage cylinder push rods from brake

shoes and remove cylinder.

NOTE:
On Chevrolet, it is necessary to re-

move the anchor pin which holds the front wheel

cylinder to flange plate to remove the front

wheel cylinder.

Disassembly

1.
Remove boots from cylinder ends with pliers and

discard boots.

2.
Remove and discard pistons and cups.

Inspection and Cleaning

NOTE:
Staining is not to be confused with

corrosion. Corrosion can be identified as pits

or excessive bore roughness.

1.
Inspect cylinder bore. Check for staining and corro-

sion.
Discard cylinder if corroded.

2.
Polish any discolored or stained area with crocus

cloth by revolving the cylinder on the cloth sup-

ported by a finger. Do not slide tfce cloth in a

lengthwise manner under pressure.

NOTE:
Before washing parts, hands must be

clean. Do not wash hands in gasoline or oil

before cleaning parts. Use soap and water to

clean hands.

3.
Wash the cylinder and metal parts in Declene or

equivalent.

4.
Shake excess cleaning fluid from the cylinder-. Do

not use a rag to dry the cylinder as lint from the rag

cannot be kept from the cylinder bore surfaces.

5. Check piston for scratches or other visual damage;

replace if necessary.

Assembly (Fig. 33)

1.
Lubricate the cylinder bore and counterbore with

clean brake fluid and insert spring - expander

assembly.

2.
Install new cups with flat surfaces toward outer

ends of cylinder. Be sure cups are lint and dirt free

before insertion. Do not lubricate cups prior to

assembly.

3.
Install new Durex pistons into cylinder with flat

surfaces toward center of cylinder. Do not lubri-

cate pistons before installation.

4.
Press new boots into cylinder counterbores by hand.

Do not lubricate boots prior to installation.

Installation

1.
Position wheel cylinder to brake flange plate. Install

screws and tighten securely.

NOTE:
On Chevrolet front wheels, mount front

wheel cylinders to the brake flange plate by

installing the threaded anchor pin through the

wheel cylinder housing and tighten to 130 lb. ft.

To secure, peen over the flat washer on the

anchor pin.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-22

2.
Replace ail push rods and pull back springs.

3.
Connect hose or line to wheel cylinder.

NOTE:
If replacing front wheel cylinder, con-

nect hose and inspect installation as outlined in

"Hydraulic Brake Hose Replacement".

4.
Install drum and wheel.

5. Bleed brakes as outlined in this section.

ANCHOR PIN

Front Wheel

1.
Raise front of vehicle and place on jack stands.

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Disengage anchor pin lock and remove anchor pin by

turning counterclockwise.

5. Place new lock plate on anchor pin and pass pin

through the hole in flange plate and screw into tapped

hole in spindle support.

6. Torque pin to 130 lb. ft. and lock by peening over

washer tabs.

7. Install brake shoe guide plate, link and pull back

springs.

8. Adjust brakes, install drum and wheel as outlined

in this section. Test brake operation.

Rear Wheel

Two type anchor pins are used in production for the

rear wheels. The riveted type is not serviced and if

failure or damage should occur to either the anchor

pin or flange plate, both parts will have to be replaced

and the threaded type anchor pin used.

Threaded Type

1.
Raise rear of vehicle and place on jack stands,

2.
Remove wheel and drum as outlined in this section.

3.
Remove brake shoe pull back springs, link and guide

plate.

4.
Remove anchor pin retaining nut and washer and

remove pin from flange plate.

5. Position anchor pin to flange plate, install lock

washer and nut, and torque pin to 80 lb. ft.

6. Install brake shoe guide plate, link and pull back

springs.

7. Adjust brakes and install drum and wheel as outlined

in this section.

8. Test brake operation.

BRAKE DRUMS

Front brake drums are the demountable type; that is,

they can be removed without removing the hub. Rear

brake drums are demountable and may be removed

wihtout removing the axle shaft.

A lanced "knock out" area (fig. 34) is provided in

the web of the brake drum for servicing purposes in

the event retracting of the brake shoes is required in

order to remove the drum.

A small screw driver or hooked wire may be inserted

to disengage the automatic adjuster actuating lever so

the star wheel may be turned.

Removal

1.
Raise vehicle and place on jack stand.
2.
Remove wheel and tire assembly, back off brake

adjustment and remove drum.

Inspection and Reconditioning

Whenever brake drums are removed they should be

thoroughly cleaned and inspected for cracks, scores,

deep grooves, and out-of-round. Any of these conditions

must be corrected since they can impair the efficiency

of brake operation and also can cause premature failure

of other parts.

Smooth up any slight scores by polishing with fine

emery cloth. Heavy or extensive scoring will cause

excessive brake lining wear and it will probably be

necessary to rebore in order to true up the braking

surface.

An out-of-round drum makes accurate brake shoe

adjustment impossible and is likely to cause excessive

wear of other parts of brake mechanism due to its

eccentric action.

A drum that is more than .008" out-of-round on the

diameter is unfit for service and should be rebored.

Out-of^round, as well as taper and wear can be ac-

curately measured with an inside micrometer fitted

with proper extension rods.

If drum is to be rebored for use with standard size

brake facings which are worn very little, only enough

metal should be removed to obtain a true smooth braking

surface.

If drum has to be rebored more than .020" over the

standard diameter, it should be rebored to .060" diameter

oversize and the brake facing should be replaced with

.030"
oversize facings.

A brake drum must not be rebored more than .060"

over the maximum standard diameter, since removal

of more metal will effect, dissipation of heat and may

cause distortion of drum. Chevrolet brake facing is

not furnished larger than .030" oversize and this will

not work efficiently in drums bored more than .060"

oversize.

Brake drums may be refinished either by turning or

grinding. Best brake performance is obtained by turning

drums with a very fine feed. To insure maximum lining

life,
the refinished braking surface must be smooth and

free from chatter or tool marks, and run-out must not

exceed .005" total indicator reading.

Cleaning

New brake drums in parts stock are given a light.

coating of rust proofing oil to prevent the formation of

rust on the critical braking surfaces during the time

that the drums are in storage.

This rust proofing oil must be carefully removed

before the drum is placed in service to prevent any

of this oil from getting on the brake shoe facings, which

might cause an extreme brake grab condition.

It is recommended that a suitable volatile, non-toxic,

greaseless type solvent be used to clean the oil from the

braking surface of the new brake drums before they are

•placed in service to insure the cleanest possible surface.

Gasoline or kerosene should not be used as there is

danger that a portion of the diluated oil substance may

be left on the braking surface that may later cause

difficulty.

Installation

1.
Make brake adjustment as outlined in this section.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-23

Fig.
34—Brake Drum Access Hole

2.

Install brake drum, aligning tang with wheel hub

(fig. 18).

3.
Install wheel and tire assembly.

. 4. Make final brake adjustment as outlined in this

section and check brake operation.

BRAKE PIPE DISTRIBUTION AND SWITCH

ASSEMBLY (Fig. 2)

Removal

1.
Disconnect battery cable.

2.
Disconnect electrical lead from switch assembly.

3.
Place dry rags below the switch to absorb any fluid

spilled during removal of switch.

4.
Disconnect four hydraulic lines from connections
at switch. If necessary, loosen line connections at

main cylinder to loosen lines. Cover open line ends

with clean, lint-free material to prevent foreign

matter from entering the system.

5.
Remove mounting screw and remove switch from

vehicle.

Installation

1.
Make sure new switch is clean and free of dust and

lint. If any doubt exists, wash switch in Declene,

or equivalent, and dry with air.

2.
Place switch in position and secure to bracket with

mounting screw.

3.
Remove protective material from open hydraulic

brake lines and connect lines to switch. If necessary,

tighten brake line connections at main cylinder.

4.
Connect switch electrical lead.

5.
Connect battery cable.

6. Bleed the brake systems as outlined in this section.

CAMARO PRESSURE REGULATOR VALVE

(AIR CONDITIONED MODELS ONLY)

Removal (Fig. 3)

1.
Place dry rags below valve to absorb any fluid

spilled during removal of valve.

2.
Disconnect hydraulic brake lines from both sides

of switch. Cover open line ends with clean, lint-free

material to prevent foreign matter from entering

the system.

3.
Remove mounting screw and remove switch from

vehicle.

Installation

1.
Make sure new valve is clean and free of dust and

lint. If any doubt exists, wash valve in Declene, or

equivalent, and dry with air.

2.
Place valve in position and secure to frame side

rail with mounting screw.

3.
Remove protective material from open hydraulic

brake lines and connect lines to each side of valve.

4.
Bleed brake system as outlined in this section.

CHEVROLET CHASSIS SERVICE