1967 CHEVROLET CAMARO air suspension

LUBRICATION 0-17

LUBRICATE EVERY 6,000 MILES

LUBRICATE EVERY 12,000 MILES

LUBRICATE EVERY 36,000 MILES

Refill Positraction Rear Axle with

Special Lubricant Only.
GL—Multi-purpose
or
Universal Gear Lubricant4

WB-Wheel Bearing Lubricant

(Whenever Brakes are serviced)

CL—Chassis Lubricant

EO-EngineOil
AT-Automatic Transmission Fluid {Type
A)

BF-Brake Fluid

Fig.
32—Lubrication Diagram—Chevrolet

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-18

12

LUBRICATE EVERY 6000 MILES GL -Multi-purpose Gear Lubricant*

WB—Wheel Bearing Lubricant

LUBRICATE EVERY 12000 MILES (Whenever Brakes are serviced)

CL —Chassis Lubricant

LUBRICATE EVERY 36000 MILES E°-En9ine°il

"Refill Positraction Rear Axle with Special Positraction Rear Axle

Lubricant Only.
AT —Automatic Transmission Fluid (Type A)

SL —Steering Gear Lubricant

BF -Hydraulic Brake Fluid

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
33—Lubrication Diagram—Chevelle

4.
Air Cleaner

5. Crankcase Breather Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master CylincU

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-19

.
3-SPEED
4-SPEED

7 OVER DRIVE

10 9 5 1 6 2 '
AUTOMATIC

3 12 11

LUBRICATE EVERY 6,000 MILES GL-Gear Lubricant*

WB-Wheel Bearing Lubricant

(Wh Bk
AT-Automdtic Transmission Fluid

^ WB-Wheel Bearing Lubricant (Type A)

-TV
LUBRICATE
EVERY 12,000 MILES (Whenever Brakes are serviced)

' CL—Chassis Lubricant

• LUBRICATE EVERY 36,000 MILES EO_Engine Oil
BF
-Brake Fluid

•Refill Positt

Special Lubricant Only.
Axl«
with

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
Fig.
34—Lubrication Diagram—Chevy I!

4. Air Cleaner

5. Crankcase Breather. Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9.
Oil Filter
10.
Battery

11.
Parking Brake

12.
Brake Master Cylinder

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-20

3-SPEED

4—SPEED

AUTOMATIC

LUBRICATE EVERY 6000 MILES

LUBRICATE EVERY 12000 MILES

LUBRICATE EVERY 36000 MILES

*
Refill
positraction rear axle with

special lubricant only.
GL -GEAR LUBRICANT*

WB-WHEEL BEARING LUBRICANT

(WHENEVER BRAKES
ARE
SERVICED)

CL -CHASSIS LUBRICANT

CO-ENGINE
Oil;
AT -AUTOMATIC TRANSMISSION

FLUID (TYPE
A)

BF -BRAKE FLUID

Fig.
35—Lubricafion Diagram—Camaro

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air Cleaner

5. Crankcase Breathe Cap

6. Front Wheel Bearings
7. Transmission

8. Rear Axle

9. Oil Filter
10.
Battery,

11.
Parking Brake

12.
Brake Master Cylinder

BODY LUBRICATION

See Body Service Manual
for
Body Lubrication,

cept Corvette)
(Ex-

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION
0-21

6

3-SPEED

4-SPEED

AUTOMATIC

10

LUBRICATE EVERY 6,000 MILES GL -Multi-purpose
or
Universal Gear Lubrincant*

-(V LUBRICATE EVERY 12,000 MILES WB-Wheel Bearing Lubricant

V/^ (Whenever Brakes
are
serviced)
AT —Automatic Transmission Fluid (Type)

BF -Brake Fluid

a
LUBRICATE EVERY 36,000 MILES

* Refill Positraction Rear Axle with

Special Lubricant Only.
CL -Chassis Lubricant

EO—Engine
Oil

Fig.
36—Lubrication Diagram—Corvette

1.
Front Suspension

2.
Steering Linkage

3. Steering Gear
4.
Air
Cleaner

5. Front Wheel

Bearings
6. Transmission

7. Rear Axle

8.
Oil
Filter
9. Battery

10.
Parking Brake

11.
Brake Master Cylinder

BODY LUBRICATION POINTS (CORVETTE)

Lubricate the following items when possible.

Hood Latch Mechanism and Hinges --Apply light engine oil

to pivot points. Don't oil lock pins or catch plates.

i

Rear Compartment Lid Release and Hinges --Apply light

engine
oil.

Side Door Hinge Pins—Apply light engine oil.
Door Lock Rotor and Striker Plate—Apply light engine oil or

stainless stick lubricant.

Lock Cylinders—Lubricate with powdered graphite.

Window Regulators and Controls and Door Lock Remote

Link —Apply light engine
oil.

Gas Tank Filler Cap Hinge—Apply light engine oil.

Weatherstrips and Rubber Bumpers —Coat lightly with
a

rubber lubricant.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 2

FRAME

INDEX

Page

General Description 2-1

Chevrolet 2-1

Cheveile '. 2-1

Repair Procedures 2-1
Page

Checking Frame Alignment 2-1

Car Preparation 2-1

Tramming Sequence 2-1

Reference Point Dimensions 2-1

GENERAL DESCRIPTION

CHEVROLET AND CHEVELLE

Frames used on Chevrolet and Cheveile lines are basi-

cally the same, consisting of full length right and left

side members joined laterally by crossmembers. Sev-

eral different frames are used in each line to meet the

various vehicle size and function requirements but the

basic shape for each line remains the same. Differences

between frames in a given line exist only in metal gauge,

part size and numbers of parts necessary to meet the

particular structural requirements of the models

involved.

CORVETTE

The Corvette frame is a rigid perimeter unit, with five
crossmembers. From the rear kick-up forward, trap-

azoidal shaped, closed side members outline and protect

the passenger compartment. At the cowl area, the side

members curve inward in a sweeping "S" shape, to pro-

vide a sturdy foundation for the engine mounts and clear-

ance for front wheel movement. From the kick-up

rearward, box-sectioned side rails provide fore and aft

support for the rear axle and suspension. Lateral sup-

port is provided by five variously shaped welded-in

crossmembers, including the front unit, which formerly

was bolted-in.

CHEVY II AND CAMARO

Underbody alignment checking procedures will be found

in the Body Service Manual.

REPAIR PROCEDURES

CHECKING FRAME ALIGNMENT

Vehicles involved in an accident of any nature which

might result in a "swayed" or "sprung" frame should

always be checked for proper frame alingment in addi-

tion to steering geometry and wheel alignment.

CAR PREPARATION

Preparing the car for the frame alignment check in-

volves the following:

1.
Place the car on level surface.

2.
The weight of the car should be supported at the

wheel locations.

3.
A visual damage inspection should be made to elim-

inate needless measuring. Obviously damaged or

misaligned areas can often be located by sight.

TRAMMING SEQUENCE

When checking a frame for alignment in case of dam-

age,
the first step is horizontal "X" checking with a

tram from similar given points on opposite side of the

frame.

Frame alignment checks on all models should be made

with the tram points set at the center of each locating

point indicated and the cross bar level to insure

accuracy.

When "X" checking any section of the frame, the

measurements should agree within 3/16". If they do not,
it means that corrections will have to be made.

If a tram gauge is not available, the "plumb bob"

method of checking may be used. To assure any degree

of accuracy when using this method, the vehicle should

be on a level floor.

By using this method, it is only necessary to have a
#

piece of cord attached to an ordinary surveyor's plumb

bob.
When measuring the distance between two points,

the free end of the cord should be placed on the reference

point allowing the plumb bob to hang on the floor. A check

mark should be made on the floor just under the tip of

the plumb bob. This operation should be repeated at all

reference points. With these points located on the floor,

they may easily be measured with a rule.

The second step is checking the vertical dimensions

from the datum plane to the points to be trammed. With

the proper settings the tram bar will be on a plane

parallel to that of the frame. The exception to this would '

be when one of the reference locations is included in the

misaligned area; then the parallel plane between the

frame and the tram bar may not prevail. After com-

pletion of the repairs, the tram gauge should be set at

the specified dimension to check the accuracy of the re-

pair operation.

ALIGNMENT REFERENCE POINT DIMENSIONS

Dimensions to holes are measured to dead center of

the holes and flush to the adjacent surface metal.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
3

FRONT SUSPENSION

INDEX

Page

General Description
. . . . 3-1

Maintenance and Adjustments
3-3

Front Wheel Bearing Adjustment
3-3

Front End Alignment
3-5 .

Alignment Preliminary Steps ............
3-5

Caster
and
Camber Adjustments
. . 3-5

Chevelle, Caxnaro
and
Corvette
3-5

Chevrolet and Chevy
II 3-6

Steering Axis Inclination
3-6

Toe-in Adjustment
3-6

Cornering Wheel Relationship
3-6

Riding Heigit
and
Coil Spring Sag
3-7

Repair Procedures
3-8

Front Brake Drum (Chevrolet, Camaro, Chevelle,

Chevy E)
. . 3-8

Removal
3-8

Installation
3-8

Front Wheel Hub
3-8

Replacement
. . . . . 3-8

Replacement
of
Hub Wheel Bolts
3-8

Front Wheel Bearings
. . 3-8

Removal
3-8

Inspection
3-9

Repairs
. . 3-9

Replacement
of
Bearing Cups
3-9

Installation
3-9

Steering Knuckle
. . . 3-9

Removal
3-9

Installation
3-9

Shock Absorber
3-10

Chevrolet, Chevelle, Camaro
and

Corvette
3-10

Removal
, . 3-10

Installation
3-10

Chevy
It 3-11

Removal
3-11

Installation
3-11

Stabilizer
Bar 3-11

Removal
3-11

Installation
3-11

Strut Rod
3-11

Chevrolet and Chevy
II 3-11

Removal
3-11

Installation
3-12

Front Coil Springs
3-12

Chevrolet
3-12

Removal
3-12

Installation
3-13

Chevelle
and
Camaro
3-13

Removal
3-13

Installation
3-14

Chevy H
3-14

Removal
3-14

Spring Seat Disassembly and Assembly
3-15

Installation
3-15

Corvette
3-15

Lower Control Arm Spherical Joint
.' 3-16

Chevrolet, Chevelle, Camaro and

Corvette
3-16

Inspection
. 3-16

Chevrolet and Corvette
3-16

Removal
3-16

Installation
3-16
Page

Chevelle
and
Camaro
3-17

Removal
3-17

Installation
. . . . 3-17

Chevy
II 3-17

Inspection
. 3-17

Removal
3-17

Installation
3-17

Lube Fittings
3-18

Lower Control Arm
. . . . 3-18

Chevrolet
. 3-18

Removal
3-18

Installation
3-18

Chevelle and Camaro
3-18

Removal
3-18

Installation
3-18

Chevy H
3-18

Removal
3-18

Installation
3-19

Corvette
3-19

Removal
3-19

mstallation
3-19

Lower Control Arm Bushings
3-20

Chevrolet
3-20

Removal
3-20

Installation
3-20

Chevelle and Camaro
. 3-20

Removal
3-20

Installation
3-20

Chevy H
3-21

Removal
* 3-21

InstaEation
3-21

Cross Shaft and/or Bushings
. 3-21

Corvette
3-21

Removal
3-21

Installation
3-21

Upper Control Arm Spherical Joint
3-21

Chevrolet, Chevelle, Camaro and Corvette
..... 3-21

Inspection.
3-21

Replacement
3-21

Chevy
II 3-21

Inspection
3-21

Replacement
3-21

Lube Fittings
3-22

Upper Control Arm
3-22

Chevrolet, Chevelle, Camaro
and
Corvette
3-22

Removal
3-22

Installation
3-22

Chevy H
3-22

Removal
3-22

Installation
3-23

Upper Control Arm Cross Shaft

and/or Bushings
3-23

Chevrolet, Camaro and Chevelle
3-23

Removal
. 3-23

Installation
3-23

Chevy H
3-24

Removal
3-24

Installation
. . . 3-25

Corvette
3-25

Removal
3-25

Installation
3-25

Special Tools
3-26

Specifications
...'..'
At rear of Book

GENERAL DESCRIPTION

The 1967 Chevrolet, Chevelle, Camaro, Chevy n and

Corvette front suspension systems are basically similar,

being of the
S.L.A.
(short-long arm) type with independent

coil springs. In the Chevrolet, Chevelle, Camaro and

Corvette the springs ride on the lower control arms; in
the Chevy II the springs ride on the upper control arms.

Spherical joints connect the upper and lower arms to the

steering knuckle. Tapered roller wheel bearings are

used.

Camber angle is adjusted, on the Chevrolet and Chevy n

CHEVROLET CHASSIS SERVICE MANIM

FRONT SUSPENSION 3-8

REPAIR PROCEDURES

Unless otherwise indicated all repair procedures will

apply to all five vehicles covered in this manual.

CAUTION: During any operations which in-

clude breaking the ball stud loose from the

knuckle boss extreme care must be used to as-

sure that the ball stud seal is not damaged or

cut. A recommended way to loosen the stud is to

place a flat bar stock against the knuckle boss

and strike the bar rather than the knuckle.

FRONT BRAKE DRUM-CHEVROLET, CAMARO,

CHEVELLE, CHEVY It

Removal

1.
Remove hub caps, partially loosen wheel nuts and

raise vehicle from floor. Remove wheel nuts and

wheel.

2.
Remove brake drum. In some cases it may be nec-

essary to back off brake adjustment because of

scored drum or unevenly worn brake linings.

3.
Check brake drum for concentricity, damaged pilot

diameter or scored braking surface. Lightly sand

braking surface and wipe clean.

Installation

1.
Install drum over hub bolts making sure alignment

dowel on drum web indexes with hole in wheel hub.

This will assure proper drum alignment with hub

bolts and hub pilot diameter.

2.
Install wheel and partially tighten wheel nuts.

3.
Re-adjust brake shoes to original setting. It may be

necessary to re-adjust brake shoes on both front

and/or rear wheels to assure balanced brake adjust-

ment. See Section 5 for brake adjustment procedure.

4.
Lower vehicle to floor, tighten hub wheel nuts and in-

stall hub cap.

FRONT WHEEL HUB

Replacement

1.
Remove hub caps, break loose the wheel stud nuts
VM" DIA. PIPE OR ARBOR

>l

INNER CUP

OUTER CUP
JL
RADIUS

e^

Fig.
10 - Pressing Front Hub Bolts (Typical)
Fig.
11 - Front Wheel Bearing Cop Removers

and raise vehicle. Remove wheel nuts, wheel and

tire and brake drum or (on Corvette) brake caliper

and brake disc.

NOTE:
On the Corvette, the hub and brake disc

are serviced as a complete assembly.

2.
Pry out hub grease cap, cotter pin, spindle nut and

washer,
and
remove hub. Do not drop wheel bearings.

3.
Reverse this procedure to install.

Replacement of Wheel Hub Bolts

It may be necessary to replace damaged wheel hub

bolts.
In this case, service the hub in the following

manner.

1.
Remove the hub bolts with a press or hammer.

These bolts are not peened into the hub. Do not

damage wheel mounting surface on hub flange.

2.
Install new serrated bolt into hole in
hub.
Tap lightly

with a hammer to start bolt serrations in hole, mak-

ing sure that bolt is square with hub flange.

3.
Press bolt into flange until head is fully seated

against hub flange (fig. 10).

FRONT WHEEL BEARINGS

Removal '

1.
Remove wheel hub as described above.

NOTE: Discard cotter pin. Install new cotter

pin when assembling.

2.
Remove outer roller bearing assembly from hub with

fingers. The inner bearing assembly will remain in

the hub and may be removed after prying out the

inner bearing lip seal assembly. Discard seal.

3.
Wash all parts thoroughly in cleaning solvent and

blow dry.

CHEVROLET CHASSIS SERVICE MANUAL