2007 FORD FIESTA Workshop Manual

206-09A-I 5 Anti-Lock Control 206-09A-15
REMOVAL AND INSTALLATION
5. Detach the brake tubes from the bulkhead. 10. Remove the HCU and ABS module
assembly and the support bracket.
6. Disconnect the anti-lock brake system (ABS)
module electrical connector.
11. Detach the HCU and ABS module assembly
from the support bracket.
7. Raise and support the vehicle. For additional
information, refer to Section
100-02 [Jacking 12. Remove the HCU to ABS module retaining
and Lifting]. bolts.
8. Remove the HCU and ABS module support
bracket lower retaining bolt.
I 9. Lower the vehicle.
13. Remove the ABS module.
Installation
I. To install, reverse the removal procedure.
2006.0 Fiesta 1212006 G327317en
procarmanuals.com

206-09A-16 Anti-Lock Control 206-09A-16
REMOVAL AND INSTALLATION
2. Bleed the brake system. For additional
information, refer to Section 206-00 [Brake
System
- General Information].
2006.0 Fiesta 1212006 G327317en
procarmanuals.com

206-09A-I 7 Anti-Lock Control 206-09A-I 7
REMOVAL AND INSTALLATION
Anti-Lock Brake System (ABS) Module - Vehicles Built From:
0512004
Materials Remove
the brake master cylinder to HCU
brake tubes.
Name Specification
I Super DOT 4 brake fluid I ESD-M6C57-A I
Removal
All vehicles
A CAUTI0N:lf brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Detach the engine wiring harness electrical
connector from the wheelhouse assembly.
Left-hand drive vehicles
2. Remove the brake master cylinder.
For additional information, refer to: Brake
Master Cylinder
- LHD (206-06 Hydraulic
Brake Actuation, Removal and Installation).
3. CAUTIONS:
&ap the brake tubes to prevent fluid loss
or dirt ingress.
Aplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
Right-hand drive vehicles
4. Remove the battery tray.
For additional information, refer to: Battery Tray (41 4-01 Battery, Mounting and Cables,
Removal and Installation).
5. CAUTIONS:
hap the brake tubes to prevent fluid loss
or dirt ingress.
nplug the hydraulic control unit (HCU)
ports to prevent fluid loss or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
Disconnect the brake master cylinder to HCU
brake tubes from the HCU.
All vehicles
6. CAUTIONS:
2006.0 Fiesta 1212006 G406272en
procarmanuals.com

206-09A-I 8 Anti-Lock Control 206-09A-18
REMOVAL AND INSTALLATION
9. Remove the HCU and ABS module support hap the brake tubes to prevent fluid loss bracket lower retaining or dirt ingress. /-
Aplug the HCU ports to prevent fluid loss
or dirt ingress.
N0TE:Make a note of the position of the brake
tubes to aid installation.
Disconnect the brake tubes from the HCU.
Detach the brake tubes from the bulkhead.
7m &AUTION:C~~ the anti-lock brake system
(ABS) module electrical connector and
socket to prevent dirt and fluid ingress.
Disconnect the ABS module electrical
connector.
1. Depress the locking tangs.
2. Release the retainer.
8. Raise and support the vehicle. For additional
information, refer to: (100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation). 10.
Lower the vehicle.
11. Remove the HCU and ABS module
assembly and the support bracket.
12. Detach the HCU and ABS module assembly
from the support bracket.
2006.0 Fiesta 12/2006 G406272en
procarmanuals.com

206-09A-19 Anti-Lock Control 206-09A-19
REMOVAL AND INSTALLATION
13. Remove the ABS module.
Installation
I. To install, reverse the removal procedure.
2. Bleed the brake system. For additional
information, refer to:
(206-00 Brake System
= General Information)
Brake System Bleeding (General
Procedures),
Brake System Pressure Bleeding (General
Procedures).
i
2006.0 Fiesta 121~0o6 G406272en
procarmanuals.com

206-09A-20 Anti-Lock Control 206-0949-20
REMOVAL AND INSTALLATION
Rear Wheel Speed Sensor(l2 785 0)
Removal
All vehicles
I. Raise and support the vehicle. For additional
information, refer to: (100-02 Jacking and
Lifting)
Jacking (Description and Operation),
Lifting (Description and Operation).
Vehicles with rear drum brakes
2. Detach the wheel speed sensor from the
wheel spindle on both sides.
Vehicles with rear disc brakes
3. Detach the wheel speed sensor from the
wheel spindle on both sides.
4. Detach the wheel speed sensor wiring
harness from the wheel speed sensor wiring
harness support bracket on both sides.
All vehicles
5. Disconnect the wheel speed sensor electrical
connector.
6. Detach the wheel speed sensor support
bracket and wheel speed sensor wiring
harness from the beam axle.
Discard the retaining clips.
2006.0 Fiesta 1212006 GI 83775en
procarmanuals.com

206-09A-21 Anti-Lock Control 206-09A-21
REMOVAL AND INSTALLATION
7. Detach the wheel speed sensor wiring
harness from the wheel speed sensor
/ 1 support bracket.
Discard the retaining clips.
8. Detach the wheel speed sensor wiring
harness from the beam axle on both sides.
9. Remove the rear wheel speed sensor.
Installation
I. N0TE:lnstall new retaining clips.
To install, reverse the removal procedure.
2006.0 Fiesta 1212006 GI 83775en
procarmanuals.com

206-09A-22 Anti-Lock Control 206-09A-22
REMOVAL AND INSTALLATION
Rear Wheel Speed Sensor Ring(l2 788 0)
Special Tool(s)
I I Installer, ABS Sensor Ring I
General Eaui~ment
I Soft faced hammer I
Removal
Remove and discard the wheel hub retaining \.
nut.
Vehicles with rear drum brakes
All vehicles
1. Remove the brake drum. 5. Remove and discard the wheel speed sensor
For additional information, refer to: Brake ring
(brake disc shown).
Drum
(206-02 Drum Brake, Removal and
Installation).
Vehicles with rear disc brakes
2. Remove the dust cap.
Installation
All vehicles
1. CAUTIONS:
AMake sure the wheel speed sensor ring 3. Remove the brake disc.
is not knocked, damaged and kept free from
For additional information, refer to: Brake metal
fragments.
Disc
(206-04 Rear Disc Brake, Removal and
Installation).
A~rotect the face of the wheel speed
sensor ring with a non-ferrous flat block to
4. Remove the wheel hub.
prevent damage.
AMake sure the wheel hub or brake drum
is adequately supported and do not allow
it
to rest on the wheel studs. f
AMake sure the wheel speed sensor ring ''- '
is pressed on slowly and squarely until fully
seated.
ADO not exceed a maximum load of 10 kN.
2006.0 Fiesta 1212006 GI 83776en
procarmanuals.com