2007 FORD FIESTA Workshop Manual

204-00-1 7 Suspension System - General Information 204-00-1 7
GENERAL PROCEDURES
Front Toe Adjustment(l4 11 7 0)
I
N0TE:Make sure that the vehicle is standing on a 4. Rotate the tie-rods an equal amount in either
level surface. a clockwise or a counterclockwise direction
1. Centralize the steering and lock it in position. to
adjust the toe setting.
For additional information, refer to:
Specifications
(204-00, Specifications).
2. Loosen the tie-rod end locknuts.
3. Remove the steering gear boot outer clamps.
5. Tighten the tie-rod end locknuts.
For additional information, refer to: Tie Rod
End (21
1-03 Steering Linkage, Removal and
Installation).
6. Install the steering gear boot outer clamps.
2006.0 Fiesta 1212006 GI 7387en
procarmanuals.com

procarmanuals.com

204-01 -1 Front Suspension 204-01 -1
SECTION 204-01 Front Suspension
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
Specifications.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.DESCRIPTION AND OPERATION
Front Suspension ........................................................................\
........................................
DIAGNOSIS AND TESTING
Front Suspension ........................................................................\
........................................
PAGE
REMOVAL AND INSTALLATION
Front Stabilizer Bar Bushing ...... .... . . . . . . .. . . .. . . .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (14 754 0)
204-01 -6
Lower Arm ........................................................................\
.............................. (14 706 0) 204-0 1 -7
Front Stabilizer Bar ........................................................................\
................. (14 752 0) 204-0 1 -9
Wheel Knuckle.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (1 4 343 0)
204-01 -1 3
i Front Strut and Spring Assembly ................................................................... (14 781 0) 204-01-19
Front Wheel Bearing ........................................................................\
........... (14 411 0) 204-01 -21
DISASSEMBLY AND ASSEMBLY
Front Strut and Spring Assembly ............................................................... (14 783 4)
204-01 -23
procarmanuals.com

204-01 -2 Front Suspension 204-01 -2
SPECIFICATIONS
I Top mount retaining nuts I 25 I 18 I - I
Torque Specifications
I Thrust bearing retaining nut I 48 I 35 I - I
Stabilizer bar connecting link to strut and spring
retaining nut Ib-in
I Wheel
knuckle to suspension strut pinch bolt I 85 I 63 I - I
Ib-ft Item Nm
Brake caliper anchor plate retaining bolts
Lower arm ball joint to wheel knuckle retaining nut
I Steering gear retaining bolts I 48 I 35 I - I
Tie-rod end retaining nut
Stabilizer bar clamp retaining bolts
Stabilizer bar to connecting link retaining nut
Fb.wer arm front retaining bolt I
70
48
I Lower arm rear clamp retaining bolts I 55 I 41 I - I
48
55
55
I Crossmember front retaining bolts I 70 I 52 I - I
52
35
I Crossmember rear retaining bolts 1 Iq5 1 85 I - I
-
-
35
41
41
I Crossmember inner and outer retaining bolts 1 175 1 129 1 - I
-
-
-
I Wheel hub retaining nut 1290 1214 1 - I
I Engine support insulator center bolt I 48 I 35 I - I
2006.0 Fiesta 1212006 GI 52539en
Wheel speed sensor retaining nut
a) Refer to the procedure in this section.
9 - 80
procarmanuals.com

204-01 -3 Front Suspension 204-01 -3
DESCRIPTION AND OPERATION
Front Suspension
Overview
N0TE:During installation of the front wheel bearing
it is important to adhere to the specified installation
position, as the anti-lock brake system
( ABS )
sensor ring is located in the wheel bearing. A
coloured rubber ring is provided to indicate the
correct installation position. If the wheel bearing
were to be installed incorrectly then this would
cause failure of the ABS
.
A newly developed Mc-Pherson front suspension
with L-shaped lower arms is used. These lower
suspension arms are linked via large rubber
mountings to a reinforced and extremely rigid front
axle crossmember.
The ball head between the lower suspension arm
and the suspension strut is secured with three
rivets. Toe-in is adjusted via adjustable track rods.
The lower suspension arms can only be replaced as a complete unit.
2006.0 Fiesta IZIZOO~ GI 67080en
procarmanuals.com

204101 -4 Front Suspension 204-01 -4
DESCRIPTION
AND OPERATION
Item Description
The rear rubber mountings for the lower
suspension arms are enclosed in aluminium
brackets. This provides more vibration damping
than previously. Both the front and rear brackets
are arranged horizontally.
1
The suspension strut turret support bearings have
two separate routes for independently deflecting
the spring and shock absorber forces into the body.
This reduces the level of noise transmitted from
the road surface. Rear rubber
mounting
The correct installation position must be observed
when installing the suspension strut turret support
bearings. This is indicated by an arrow on the
suspension strut turret support bearing. The shock
absorbers are gas shock absorbers.
The spring travel has been increased by
6 mm,
and the track has been increased by
48 mm to
1477 mm.
2006.0 Fiesta 1212006 GI 67080en
procarmanuals.com

204-01 -5 Front Suspension 204-01 -5
DIAGNOSIS AND TESTING
Front Suspension
! REFER to Section 204-00 [Suspension System -
General Information].
2006.0 Fiesta 1212006 GI 7395en
procarmanuals.com

204-01 -6 Front Suspension 204-01 -6
REMOVAL AND INSTALLATION
Front Stabilizer Bar Bushing(l4 754 0)
Removal 2. Install the stabilizer bar.
1. Remove the stabilizer bar.
For additional information, refer to Stabilizer
Bar in this section.
2. Remove the stabilizer bar bushings on both
sides. For
additional information, refer to Stabilizer
Bar in this section.
Installation
1. CAUTIONS:
ADO not lubricate the stabilizer bar
bushings.
AThe stabilizer bar bushings must be
positioned with the slot facing forwards of
the stabilizer bar.
AThe stabilizer bar bushings must be
positioned as shown.
N0TE:The location of the stabilizer bar bushings
should be measured from the center mark on the
stabilizer bar.
Install the stabilizer bar bushings.
2006.0 Fiesta 1212006 G89069en
procarmanuals.com