1989 MITSUBISHI GALANT Service Repair Manual

ENGINE - Oil Pan and Oil Screen11-71
OIL PAN AND OIL SCREEN
REMOVAL AND INSTALLATION
Pre-removal and Post-installationOperation*Draining and Refilling of
Engine
011(Refer to GROUP OO-MamtenanceService.)
Sealant: MITSUBISHI GENUINE
PART No. MD970389or
equivalent


30-40 Nm1 22-28 Fibs.I
/
11-16 ft.lbs.
I
/
55-60 Nm
35-45 NmOlA0005
do-43 ft.lbs.25-33 ft.lbs.
Removal steps
1. Drain plug
2. Left member
3. Transfer assembly (Refer to GROUP
22,23-Transfer.)6-8 Nm
4-6 ft.lbs.4. Drive shaft
(Refer to GROUP 22.23-Transaxle.)
OlA0620
SO-:00 Nm *58-72 ft.lbs. 70-80’
Nm
51-58
ft.lbs.
/ - -e
95.ixhaust pipe connedtion
, .A6.Gasket
Nm17. Connection for oil return pipe (Turbo)
25-33ft.lbs.8.Gasket (Turbo)4*l 49.Oil pan
35-45
-- -
-
10. Oil
screen11. Gasket
TSB Revision

11-72
ENGINE - Oil Pan and Oil Screen
1
OlR0606
Sealant
Groove 4 m
m
(.I 6
in.)
p4L
cut off
-01 BOOS1e
SERVICE POINTS OF REMOVALMllHBAFl
9. REMOVAL OF OIL PAN
(1) Remove the oil pan mounting bolts.
(2) Tap the general service tool in between the cylinder block and the oil pan.
Caution
Do not use a screwdriver, a chisel or a similar tool
when removing the oil pan.
(3) Remove the oil pan by placing a brass bar at the corner of the general service tool and then tapping with a
hammer.
INSPECTIONMllHCACl
lCheck the oil pan for damage and cracks. Replace if faulty.
l Check the oil screen for clogging; damage and cracks.
Replace if faulty.
SERVICE POINTS OF INSTALLATIONMllHDAOl
9. INSTALLATION OF OIL PAN
(1) Use a wire brush or other tool to scrape clean all gasket surfaces of the cylinder block and oil pan so that all
loose material is removed.
(2) Gasket surfaces must be free of oil and dirt.
(3) Apply the specified sealant around the surface of the
oil
pan as specified in illustration.
Specified sealant: MITSUBISHI GENUINE PART
No.MD970389 or equivalent
NOTE
To squeeze out proper amount of sealant, cut off the
nozzle of sealant. This will provide a nozzle 4 mm
(.I6
in.) in diameter.
(4) The sealant should be applied in a continuous bead approximately 4 mm
(.I6 in.) in diameter.
1 TSB Revision

ENGINE - Cylinder Head Gasket11-73
CYLINDER HEAD GASKET
MllJA-9
REMOVAL AND INSTALLATION
9-14 Nm
7- 10 ft.lbs.
OlA0408
8-10 Nm
6-7 ft.lbs.
-11 ‘
4
A17
-16
4-6 N
m
---3-4
ftlbs.
OlA0649
17.
18.
19.20.
l **421.
22.
23.
74Removal steps
1. Branch tube
2. Air hose A (Turbo)
3. Radiator assembly (Refer to GROUP
14-Radiator.)
4. Volume air flow sensor
connector
5. Resonator assembly
6. Turbocharger waste gate solenoid (Turbo)
7. Fuel pressure solenoid (Turbo) 8. EGR solenoid (Turbo)
-
9. Air cleaner assembly
11. Connection for purge25.
hose (Turbo)12. Connection for by-passair hose (Turbo)13. Air intake hose10. Breather hose
14. Connection for air hose26.
D (Turbo)15. Connection for27.
vacuum hose28.
16. Connection for water29.
hose (Turbo)
I
Connection for water
by-pass hose
Connection for heater
hose
PCV hose
Connection for
vacuum hose (Turbo)
Connection for
high-pressure fuel hose
O-ring
Vacuum hose (Turbo) Connection for fuel
return hose
Connection for
accelerator cable or
throttle cable (Refer to GROUP
13-ServiceAdjustment
Procedures.)
Connection for brake
booster vacuum hose
Eye-bolt (Turbo)
Gasket (Turbo)
pun;;;tron for oil pipe
TSB Revision
I

11-74ENGINE - Cylinder Head Gasket

< 1990 models>
/
d34
/./At %L.
I4-6 Nm
3-4 ftlbs.
‘36
4-6
Nm3-
4 ftlbs.
2.5-3.5Nm\45
13 33
42
/A
3839/ z-i ,“g,- . .OlA0622
TSB Revision

ENGINE - Cylinder Head GasketII-75
4-6 Nm
Z&-y,bfm
‘\ .
,,\:.,.s.
46
4-6
‘Nm $7
3-4 ftlbs.
41
43
42
IO-12 Nm
7-9 ft.lbs.
05A0199
Removal steps
30. Connection for engine coolant
temperature switch
31. Connection for oxygen sensor
32. Connection for engine coolant temperature sensor
33. Connection for engine coolant
temperature gauge unit
34. Connection for air conditioning engine
coolant temperature switch
35. Connection for injector
36. Connection for EGR temperature sensor
(California vehicles only) 37. Connection for knock sensor (Turbo)
38. Connection for ianition coil
39. Connection for ignition power transistor
40. Connection for throttle position sensor
41. Connection for crankshaft position sensor
42. Connection for IAC motor
43. Connection for closed throttle position
switch
44. Connection for vacuum hoses
45. Center cover
46. Connection for spark plug cable assembly
47. Control wiring harness
TSB Revision

11-76
ENGINE - Cylinder Head Gasket
2.5-3.5
N
m
2-3 ft.lbs.
49
l’/
50
_ 65-72 ftlbs.
e g ;yb,- 0 Nm - 20 Nm - l/m. - 0 ftlbs.
- 14 ft.lbs. -4 turn +I/4 turna ,a _..--/I In +n lQQ3 mnrimls>- II ~
/
i/4wrn + 114xurnrAVJ
.vp .” .““L . ..-..-.I-^^ -^^I.~1-_ _- .-..-YU-IUU NIT5.
<199” ---I-‘-’80 Nn, - v ,.lll - Lw .-...II I” I.._^
66-77 ft Ih!
* IA +.*r..
*Replenishing
Engine Coolant
(Refer to GROUP OO-Maintenance
l Service ‘Adjustment Procedures(Refer to P.l l-57.)I
12-15 Nm
9-11
ft.lbs.
/
:WD>40-50 NmW3i,ft.lbs...,....I,30-40 NmI
3_2- 29 ftlbs.b. I\
\$ 1
‘\I
MY
L. I
Q51 ,-,?/*
r
r
30-46 Nm22-29 ft.lbs. I.5

rrl”“els~n .nNm-7nNm
48. Timing belt (Refer to P.l I-80.)49. Rocker cover
50. Semi-circular packing
51. Self locking nut (Non-Turbo)
52. Gasket (Non-Turbo)
53. Heat protector (Turbo)
54. Gasket (Turbo)55. Ring (Turbo)+, l * 56. Cylinder head assembly~~ 57. Cylinder head gasket
+ I,4 L”,,, - #l-t L”lllj8 ft.lbs. - 0 ft.lbs. - 14 ft.lbs.,J -1 IA turn + 1 IO turn
25-30 him
18-22
ft.lbs.‘54m
OlA0567
TSB Revision

ENGINE - Cylinder Head GasketII-77
SFAI ING
POINTSGaln
OlA0155
J
Front of engine I)Intake side
]
Exhaust side
SERVICE POINTS OF REMOVALMllJBAUa
21. DISCONNECTION OF HIGH-PRESSURE FUEL HOSE
Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressure
in the fuel pipe line.
For information concerning the bleeding of the residualpressure, refer to GROUP
13-On-vehicle Inspection of MFI Components.
56. REMOVAL OF CYLINDER HEAD ASSEMBLY Using the tool, loosen the bolts in the order shown in the
figure (in 2 or 3 cycles) and remove. Then remove the cylin-
der head assembly.
TSB Revision
I

ENGINE - Cylinder Head Gasket
SERVICE POINTS OF INSTALLATIONMllJDAN
57. INSTALLATION OF CYLINDER HEAD GASKET
(1) Use a scraper to clean the gasket surface of the
cylinder block.
Ident i f ido c\ (Imark\ OlAOO38
Front of
engine+Intake side
.miJ
Exhaust side Caution
Take care that no foreign material gets into the cylinder, or into coolant passages or oil passages.
(2) Make sure that the gasket has the proper identification mark for the engine.
(3) Lay the cylinder head gasket on the cylinder block with the identification mark at the front top.
56. INSTALLATION OF CYLINDER HEAD ASSEMBLY
(1) Use a scraper to clean the gasket surface of the cylin- der head assembly.
Caution
Take care that no foreign material gets into the
coolant passages or oil passages.
(2) Using the special tool and a torque wrench, tighten the bolts to the specified torque in the order shown in the
figure. (in two or three cycles.)
Caution
Install the head bolt washers as shown in the
diagram.