1989 MITSUBISHI GALANT Service Repair Manual

35-120SERVICE BRAKES - Rear Disc Brake
Steel
pips
ring
ring
St&+3
groove
a
0 0
SERVICE POINTS OF REASSEMBLYM35NDAH
11. REASSEMBLY OF SNAP RING While using a 19 mm
(.75 in.) diameter steel pipe to press
in the spring case, use the snap ring pliers to attach the
snap ring to the caliper body.
Caution
Attach the snap ring to the caliper body with the
opening facing the bleeder.
9. REASSEMBLY OF PISTON ASSEMBLY (1) Push the piston into the caliper with special tool.
NOTE
Align the grooves as illustrated.
(2) The pins on the back side of the brake pad must beplaced in the grooves in the position.
TSB Revision
1

SERVICE BRAKES - Hydraulic Unit 35-121
HYDRAULIC UNIT hl35OXAB
L
IEMOVAL AND INSTALLATION


Flared brake line nuts
I13-17 NmA9- 12ftlbs.I@
9-14 Nm7-10
ft.lbs.6
i
17-26 Nm12-19
ft.lbs.
_ _
17-26 Nm/12-19 ft.lbs.
\
17-26 Nm /12-19 ft.lbs.
Removal Steps
1.Dust shield
2. Engine coolant reservoir
3. Engine coolant reservoir bracket
I)+ 4. Brake hose connectionI)+ 5. Brake tube connection
*I)6. Relay box cover7.Connector
8. Bracket installation bolt
l + 9. Bracket A
+*10. Hydraulic unit11.Bracket D
12.Bracket B13.Bracket C
16.
Motor relay17.Valve relay Pre-removal
and Post-installation
l Draining and Supplying of Brake
l Removai and Installation of the 17-26
Nm,12-19 ft.lbs.
TSB RevisionI

35-122SERVICE BRAKES - Hydraulic Unit

9-14 Nm
17-26 Nm12-19 ft.lbs.
8
17-26 Nm12-19 ft.lbs.
16
17-26 Nm
,
17-26 Nm
12-19 ft.lbs.
17-26
Nm12-19
ft.lbs.
12-19
ft.lbs.
Removal Steps
I. Dust shield
2. Engine coolant reservoir
l +3. Engine coolant reservoir bracket
4. Brake hose connection
W 5. Brake tube connection 6. Relay box cover
7. Connector
8. Bracket installation bolt
l +9. Bracket A4*IO. Hydraulic unit
11. Bracket D12. Bracket B13. Bracket C16. Motor relay
17. Valve relay Pre-removal and Post-installation Op-
eration
eDraining and Supplying of Brake Fluid
*Removal and Installation of the Solash
(Refer to GROUP 42-Fender.)I
TSB Revision

SERVICE BRAKES -Hydraulic Unit 35-123

w1480636
Pre-removal and Post-installation Op-
Flared brake line nuts 13-17 Nm
9-12 ft.lbs.
14FO38
17-26 Nm12- 19
ft.lbs.7- 10
ft.lbs.
Removal steps
I. Dust shield
2. Engine coolant reservoir
3. Engine coolant reservoir
++ 5. Bracket tube connection 8. Bracket installation bolt
~~ 9. Bracket A4*10. Hydraulic unit
14. Hydraulic unit bracket
15. Relay box cover
16.Motor relay17.Valve relay18.Bracket tube19.2 way connector bracket
8

35-124SERVICE BRAKES - Hydraulic Unit
I-Motor relay
16Fi1773
I___-
SERVICE POINTS OF REMOVAL
6. REMOVAL OF RELAY BOX COVER
Insert the tip of a screwdriver into the space between the
hydraulic unit and the relay box cover and use it to open
the tab at one place, and then remove the cover.
10. REMOVAL OF HYDRAULIC UNIT Remove the bracket
B, C and D installation bolts, and then
take out the hydraulic unit downward.
Caution 1. The hydraulic unit is heavy, and so care should be
taken when removing it.
2. The hydraulic unit is not to be disassembled; its
nuts and bolts should absolutely not be loosened.
3. The hydraulic unit must not be dropped or other-
wise subjected to impact shocks.
4.The hydraulic unit must not be turned upside downor laid on its side.
INSPECTION
Check whether there is continuity between terminals when
there is no current flow at each relay and when there is
current flow.
MOTOR RELA
Y
III
) 2ZSowsy/
( When current /IIflows between Betweentermin I
Continuity
0685 - 86terminals
@ - @ (approx.
0 0)
1 TSB Revision

SERVICE BRAKES - Hydraulic Unit 35-125 ’
Valve relay
16R0670
I16R1771
14AO201
1
I
U14AOlS9
VALVE RELAY
FE%:; @ - @60 - 120 R
Between
No continuity
When current terminals @I - @(wfu
flows between
terminal
@I-@Continuity
(approx. 0 fl)
TSB RevisionI
5. CONNECTION OF BRAKE TUBE/4. CONNECTION OF
BRAKE HOSE
When connecting the tubes and hoses to the hydraulic
unit, be sure they are connected correctly.
(Refer to
P.35-93.)

35-126 SERVICE BRAKES - Wheel Speed Sensor
WHEEL SPEED SENSOR M35oVAE
REMOVAL AND INSTALLATION
9-14 Nm
7-10 ft.lbs.
9- ldNm7- 10 ft.lbs.
~~Q!-yJl~~@
9-14 N
m
7- 10
ft.lbs.
14A0615
Pre-removal and Post-installation
Operation
@Removal and Installation of theSplash Shield(Refer to GROUP
42-Fender.)
Front speed sensor removal steps
4w1. Front toothed rotor2. Clip3. Connection for front speed sensor
l e e+ 4. Front speed sensorl +5. Front speed sensor bracket
Rear speed sensor removal steps
*I)6. Rear toothed rotor 7. Clip
8. Cable band
9. Connection for rear speed sensor
+e l + 10. Rear speed sensorw+ 11. Rear speed sensor bracket
TSB Revision
/-..

Pre-removal and Post-installation
SERVICE BRAKES - Wheel Speed Sensor 35-127

2
7-10 ftlbs.
7-10 ft.lbs.
9-14 Nm
Front speed sensor removal steps
*I)1. Front toothed rotor
2. Clip
+* l a3. Front speed sensor connection
**4. Front speed sensor 5. Front speed sensor bracket
14AO616
Rear speed sensor removal steps
6. Rear toothed rotor (Refer to GROUP 27-Rear Axle Hub)
7. Clip
8. Cable band
l * I)49. Rear speed sensor connection10. Rear speed sensor
12. O-ring
TSB Revision