1989 MITSUBISHI GALANT Service Repair Manual

31-6WHEEL AND TIRE - Wheel and Tire
INSTRUCTIONS FOR ALUMINUM TYPE WHk&g
1. Aluminum is vulnerable to alkalies. If
a vehicle washing
detergent has been used, or salt from sea water or road
chemicals has adhered, wash the vehicle as soon as
possible. After washing the vehicle, apply body or wheel
wax to the aluminum type wheels to prevent corrosion.
2.When cleaning the vehicle with steam, do not direct steam
onto the aluminum type wheels.
When tightening nuts for aluminum type wheels, particular- ly observe the following:
(I) Clean the hub surface of aluminum type wheels.
(2) After finger-tightening wheel nuts, tighten them to specifications.
(3) Do not use an impact wrench or push the wrench by foot to tighten the wheel nuts.
(4) Do not apply oil to the threaded portions.
INSTRUCTIONS FOR TIRE CHAINS AND SNOW
TIRES M31GGbl
1.Use tire chains only on front wheels. Do not use tire chains
on rear wheels.
2. When using snow tires, use them on all four wheels for maneuverability and safety.
INSTRUCTIONS FOR COMPACT SPARE TlR,E,,,,
1. The compact spare tire is designed to save space in theluggage compartment, and its lighter weight makes it
easier to use if a flat tire occurs.
2.The following instructions for the compact spare tire should be observed.
(1) Check the inflation pressure after installing the spare, and adjust to the specified pressure.
(2) Avoid driving through automatic car washes and over obstacles that could possibly damage the vehicle’s
undercarriage. Because the tire is smaller than the
original tire, car ground clearance is slightly reduced.
(3) The compact spare tire should not be used on any other wheels, nor should standard tires, snow tires, wheel
covers or trim rings be used with the compact spare
wheel. If such use is attempted, damage to these items
or other vehicle components may occur.
TSB Revision

32-1
POWER PLANT
MOUNT
CONTENTSM32AA-
CENTERMEMBER AND CROSSMEMBER.......8SPECIFICATIONS ............................................... 2
Service
Specifications .....................................2ENGINE MOUNTING........................................ 4
TorqueSpecifications .....................................2
ENGINEROLL
STOPPER.................................6TRANSAXLE MOUNTING................................ 5
SPECIAL
TOOL .................................................3TROUBLESHOOTING........................................4

32-2POWER PLANT MOUNT - Specifications
SPECIFICATIONS
SERVICE SPECIFICATIONSM3ZCE-
Items
Standard value Crossmember bushing (A) projection
Crossmember bushing (B) projection
Specifications
mm (in.) 7.2-10.2 (.28-.40)
mm (in.) 6.5-9.5 (.26-.37)
TORQUE SPECIFICATIONSM32cc-
Items
Engine mounting
Engine mount insulator nut (large)
Engine mount insulator nut (small)
Engine mount bracket bolt Engine mount bracket nut
Bracket
Transaxle mounting Transaxle mount insulator nut
Transaxle mount bracket to body
Engine roll stopper Front roll stopper insulator nut
Front roll stopper bracket to centermember
Rear roll stopper insulator nut
Rear roll stopper bracket to crossmember
Centermember and crossmember

Centermember installation bolts (front)
Centermember installation bolts (rear)
Stay installation bolts
Stabilizer bar bracket to crossmember
Stabilizer link installation bolts
Tie rod end ball joint to knuckle
Joint assembly and gear box connecting bolt Steering gear box assembly to return tube
Steering gear box assembly to pressure hose
Steering gear box assembly to crossmember
Pressure hose blacket
Lower arm clamp to crossmember (nut)
Lower arm clamp to crossmember (bolt)
Lower arm clamp shaft to body
Lower arm mounting bolt
Crossmember to body
NOTE*I: Vehicles built up to Dec. 1988**: Vehicles built from Jan. 1989
Nmftlbs.
60-8043-58
30-4022-29
50-6536-47
50-6536-47
17-26 12-19
60-8043-58
40-5029-36
50-6536-47
40-5029-36
40-5029-36
40-5029-36
80-10058-72
80-I 0058-72
70-8051-58
30-4222-30
35-45 25-33
24-34 17-25
15-2011-14
12-18
9-1
3
12-18 9-13
60-8043-58
9-1
4
7-10
35-47
25-34
80-10058-72
80-loo*’ [100-120]*258-72*’ [72-87]*’
100-12072-87
80-10058-72
1 TSB RevisionI

POWER PLANT MOUNT - Specifications/Special Tool32-3
Items
Centermember and crossmember

Front roll stopper to No. 1 crossmember
Front roll stopper insulator nut
No. 1 crossmember installation nut
Gusset installation bolt
Right member installation bolt (front)
Right member installation bolt (rear)
Left member installation bolt (front)
Left member installation bolt (rear)
Front exhaust pipe to exhaust fitting
Front exhaust pipe to engine
Front exhaust pipe to exhaust manifold
Front exhaust pipe clamp
Front exhaust pipe rear installation bolt
Front exhaust pipe hanger installation bolt
Stabilizer bar bracket to crossmember
Stabilizer link installation nut
Transfer assembly installation bolt MIT
Al-r
Tie rod end ball joint to knuckle
Joint assembly and gear box connecting bolt
Steering gear box assembly to return tube
Steering gear box assembly to pressure hose
Steering gear box assembly to crossmember Lower arm clamp to crossmember (nut)
Lower arm clamp to crossmember (bolt)
Lower arm clamp shaft to body
Lower arm mounting bolt
Crossmember to body
Nmftlbs.
40-5029-36
50-6536-47
80-10058-72
70-8051-58
80-10058-72
70-8051-58
80-10058-72
70-8051-58
40-6029-36
30-4022-29
30-4022-29
30-4022-29
30-4022-29
10-157-l 1
30-4222-30
35-45 25-33
55-6040-43
60-8044-57
24-34 17-25
15-2011-14
12-189-1
3
12-18 9-13
60-8043-58
35-47 25-34
80-10058-72
100-12072-87
95-12069-87
80-10058-72
SPECIAL TOOL
ToolNumber
MB991
045
Name
Bushing remover
and installerUse
Removal and installation of the crossmember
bushing
TSB RevisionI

32-4POWER PLANT MOUNT -Troubleshooting/Engine Mounting
TROUBLESHOOTING
SymptomProbable cause Remedy
Excessive engine wob-
Cracked rubber parts of insulator Replace
ble or vibration (with en-
gine rn normal condition) Insufficiently tightened parts Retighten
Abnormal noise Insufficiently tightened parts Retighten
ENGINE MOUNTING
REMOVAL AND INSTALLATION
.
TSB RevisionI
30-40 Nm22-29 ft.lbs.
Removal steps
Post-installation Operation@Lower the Engine
50-65 Nm36-47 ftlbs.
43-56 ft.lbs.
1. Pressure hose (power steering) and high
pressure hose (air conditioner)
2. BracketOIA0306
3. Engine mount bracket and body connection bolt
4. Engine mount bracket
l + 5. Mounting stopper
INSPECTION
l Check each insulator for cracks or damage
.
l Check each bracket for deformation or damage.

POWER PLANT MOUNT - Engine Mounting/Transaxle Mounting32-5
Engine side
1
Mounting stopper
Arrow 01AQOO4
TRANSAXLE MOUNTING
REMOVAL AND INSTALLATION
(Refer to GROUP 15-Air Cleaner.)
>
SERVICE POINTS OF INSTALLATIONM32GDAK
5. INSTALLATION OF MOUNTING STOPPER
Install the mounting stopper of the engine mount bracket
so that the arrow faces the center part of the engine.
Post-installation Operation @Lower
the Transaxle
@Installation of the Air Cleaner
(Refer to GROUP
15-Air Cleaner.)
60-60Nm43-58ft.lbs.
40-50Nm29-36ft.lbs.
60-80 Nm43-58 ft.lbs.
Transaxle mount
Removal steps
1. Transaxle mount bracket and transaxle
connection bolt
2. Cap3. Transaxle mount bracket installation bolt
4. Transaxle mount bracket
5. Mounting stopper
OlA0009
INSPECTIONNUZGCAHZ
l Check each insulator for cracks or damage.
l Check each bracket for deformation or damage. TSB Revision

32-6POWER PLANT MOUNT - Engine Roll Stopper
ENGINE ROLL STOPPER
REMOVAL AND INSTALLATION
M32GF-
Pre-removal Operation*Raise and Suspend the Engine to the
Extent Force IS not applied to the Engrne
Mount
I
Post-installation Operationl Lower the EngineI

40-50 Nm29-36 ftlbs.I
40-50 Nm29-36 ft.lbs.
nA5

40-50 Nm29-36 ft.lbs.
40-50Nm29-36ft.lbs. 2
136-47
ft.lbs.*
50-65 Nm36-47 ft.lbs.
Front roll stopper bracket removal steps
1. Front roll stopper bracket and engineconnection bolt
2. Front roll stopper bracket installation bolt
l +3. Front roll stopper bracket
Rear roll stopper bracket removal steps 4. Rear roll stopper bracket and engineconnection bolt
5. Rear roll stopper bracket installation bolt
l +6. Rear roll stopper bracket
NOTE+ Indicates parts which should be temporarily tightened. and then fully tightened with the weight of the engine
supported by the body
INSPECTIONM32GcAH3
l Check each insulator for cracks or damage
.
l Check each bracket for deformation or damage.
TSB Revision

POWER PLANT MOUNT - Engine Roll Stopper32-7
SERVICE POINTS OF INSTALLATIONM32GJAB
6. INSTALLATION OF REAR ROLL STOPPER BRACKET

bRear roll
in.)
After temporarily tightening the rear roll stopper bracket,
tighten so that, in the unladen vehicle condition, the
dimension of the clearance of the insulator is the specified
dimension.
Rear roll
86.7-92.7 mm
46.7-52.7 mm(1.8-2.1 in.)
Front roll
stopper bracket
/ OlR0033
cAWD-M/T>Front roll
stopper
bracket
44-50 m
m
(1.7-2.0 in.
OlAOBlO
r
,-

After temporarily tightening the rear roll stopper bracket,
tighten so that, in the unladen vehicle condition, the
distance from the center hole of the insulator to the lower
edge of the bracket is the specified distance.
3. INSTALLATION OF FRONT ROLL STOPPER BRACKET
(1) Install the front roll stopper bracket so that the part where the round hole is made is facing the front of the
vehicle.
(2) After temporarily tightening the front roll stopper
bracket, tighten so that, in the unladen vehicle condi-
tion, the distance from the center hole of the insulator
to the lower edge of the bracket is the specified
distance.
1 TSB Revision