2009 Hyundai Santa Fe Owner's Manual - RHD (UK, Australia)

6DO-IT-YOURSELF MAINTENANCE
26
!
POWER STEERING FLUID LEVELCHECKING ELECTRIC COOLING FANS
G220A01A-AAT
WARNING:
The cooling fan is controlled by engine coolant temperature and maysometimes operate even when the engine is not running. Use extreme caution when working near theblades of the cooling fan, so that you are not injured by a rotating fan blade. As the coolant temperaturedecreases the fan will automatically shut off. This is a normal condition.
G220B01A-AAT
Checking Engine Cooling Fan
The engine coolant fan should come
on automatically if the engine coolant temperature is high. G220C01A-AAT Checking Condenser Cooling Fan The condenser cooling fan should come on automatically whenever the air con- ditioning is in operation. G230A03A-GAT The power steering fluid level should
be checked regularly. To check the power steering fluid level, be sure theignition is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN"level markings on the fluid reservoir.
OCM055027L NOTE: Grinding noise from the power steer-
ing pump may be heard immedi- ately after the engine is started in extremely cold conditions (below - 20°C). If the noise stops during warmup, there is no abnormal function in the system. It is due to a power steering fluid characteristic in ex-tremely cold conditions. Recommended Fluid
Use PSF-3 type fluidNOTE: Do not start the engine when the
power steering oil reservoir is empty.
CM-aust-6.p65 5/19/2008, 6:38 PM
26

6
DO-IT-YOURSELF MAINTENANCE
27
G240A01A-DAT
POWER STEERING HOSES
It is suggested that you check the power steering hose connections for fluid leakage at those intervals speci- fied in the vehicle maintenance sched-ule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuff-ing or worn spots. Deterioration of the hoses could cause premature failure.
HSM240-1
1. Unscrew the mounting bolt on the
fuel filter and raise the fuel filter up.
REMOVAL OF WATER FROM THE FUEL FILTER
G300A02O-GAT
Diesel Engine
If the fuel filter warning lamp illumi-
nates during driving, it indicates that water has accumulated in the fuel filter. If this occurs, remove the water as described below. OCM055006L
OCM055019R
2. Loosen the drain plug at the bottom of the fuel filter.
CM-aust-6.p65 5/19/2008, 6:39 PM
27

6DO-IT-YOURSELF MAINTENANCE
28
OCM055007L
5. Open the bonnet.
6. Draw the vertical line (through the centre of each headlight) and thehorizontal line (through the centre of each headlight) on the aiming screen.And then, draw a parallel line at 30mm (1.18 in.) under the horizontalline.
7. Adjust each cut-off line of the low
beam to the parallel line with aphillips screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low beam to each vertical line with a phillips screwdriver - HORIZONTALAIMING.
Vertical aimingHorizontal aiming
HEADLIGHT AIMING ADJUSTMENT
G290A01CM-DAT Before performing aiming adjustment, make sure of the following.
1. Keep all tyres inflated to the correct pressure.
2. Place the vehicle on level ground and press the front bumper & rear bumper down several times. Placethe vehicle at a distance of 3,000 mm (118 in.) from the test wall.
3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tyre,jack, and tools). Have the driver or equivalent weight placed in driver's seat.
4. Clean the head light lenses and turn on the headlights (low beam or highbeam).
!WARNING:
Be sure to carefully wipe away any water drained out in this manner, because the fuel mixed in the watermight be ignited and result in a fire.
3. Tighten the drain plug when water
no longer comes out.
4. Installation is the reverse order of the disassembly.
5. Check to be sure that the warning lamp illuminates when the ignitionkey is turned to 'ON', and that itgoes off when the engine is started.If in doubt, consult your nearestauthorized HYUNDAI dealer.
NOTE: It is recommended that water accu- mulated in the fuel filter should be removed by an authorized Hyundai dealer.
CM-aust-6.p65 5/19/2008, 6:39 PM
28

6
DO-IT-YOURSELF MAINTENANCE
29
G290B01CM-DAT
Adjustment After Headlight Assembly Replacement
If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming shouldbe checked using an aiming screen as shown in the illustration. Turn on the headlight switch (Low Beam Positionor High Beam Position).
1. Adjust headlights so that main axis of light is parallel to centre line ofthe body and is aligned with point"P" shown in the illustration.
2. Dotted lines in the illustration show the centre of headlights. SPECIFICATION: "H" Horizontal centre line of headlightsfrom ground : Low Beam : 883 mm (34.76 in.) High Beam : 869 mm (34.21 in.) "W" Distance between each headlight centre : Low Beam : 1,402 mm (55.19 in.) High Beam : 1,144 mm (45.03 in.) "L" Distance between the headlights and the wall that the lights are tested against : 3,000 mm (118.1 in.)
G290B01TG-R
Low Beam
LW
H Cut-off line
"P"
Horizontal line
Ground line 30 mm
Vertical line
H
REPLACEMENT OF LIGHT BULBS
G260A01CM-DAT Before attempting to replace a bulb, be
sure the switch is turned to the "OFF" position.
The next paragraph shows how to
reach the light bulbs so they may bechanged. Be sure to replace the burned-out bulb with one of the same number and wattage rating.
All bulbs are available from your Hyundai
dealers Parts Department.
CAUTION:
o Keep the lamps out of contact with petroleum products, such asoil, petrol, etc.
o After heavy, driving rain or wash- ing, headlight and taillight lensescould appear frosty. This condi- tion is caused by the temperaturedifference between the lamp in- side and outside. This is similar to the condensation on your win-dows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If thewater leaks into the lamp bulb circuitry, have the vehicle checked by an authorised Hyundai dealer.
!
CM-aust-6.p65 5/19/2008, 6:39 PM
29

6DO-IT-YOURSELF MAINTENANCE
30
OCM055020
(1)
(2) (3) (4)
(5)
5. Disconnect the power cord fromthe bulb base in the back of the headlight.
6. Turn the plastic cover counterclock- wise and remove it.
OCM055010L
G270A01CM-DAT
Headlight, Front Turn Signal Light and Front Position Light
OCM055008L
OCM055021L
OCM055009L
(1) Turn signal light (2) Front position light (3) Headlight (Low Beam) (4) Headlight (High Beam) (5) Front fog light
1. Allow the bulb to cool. Wear eye protection.
2. Open the engine bonnet.
3. Always grasp the bulb by its plastic base, avoid touching the glass. 4. Using a proper tool, remove the
headlight assembly mounting bolts and nut.
CM-aust-6.p65 5/19/2008, 6:39 PM
30

6
DO-IT-YOURSELF MAINTENANCE
31
8. Push the bulb spring to remove the headlight bulb.
7. Disconnect the connector from the
bulb base in the back of the head- light.
OCM055011L
OCM055012L 9. Remove the protective cap from
the replacement bulb and install the new bulb by matching the plas- tic base with the headlight hole. Reattach the bulb spring and re-connect the connector.
10. Use the protective cap and carton
to promptly dispose of the old bulb.
11. Check for proper headlight aim.
OCM055014L
12. To replace the front turn signal light bulb or the front position light bulb, take it out from the bulb holder andinstall the new bulb.
!WARNING:
This halogen bulb contains gas
under pressure and if impacted could shatter, resulting in flying frag-ments. Always wear eye protection when servicing the bulb. Protect the bulb against abrasions or scratchesand against liquids when lighted. Turn the bulb on only when install- ing in a headlight. Replace the head-light if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb withcare.
G270A03O
CM-aust-6.p65 5/19/2008, 6:39 PM
31

6DO-IT-YOURSELF MAINTENANCE
32
G270K01CM-DAT Front Fog Light (If Installed) NOTE: It is recommended that the front fog light bulb be replaced by an authorised Hyundai dealer.
G270B01CM-GAT
Rear Combination Light
OCM055022
(3)
(1) (2)
1. Open the tail gate.
2. Remove the cover with a flat-headscrewdriver.
3. Remove the mounting screws of the rear combination light as shown with a wrench handle.
OCM052016
OCM055028
CM-aust-6.p65 5/19/2008, 6:39 PM
32

6
DO-IT-YOURSELF MAINTENANCE
33
2. Disconnect the power code by turn-
ing the bulb cover counterclockwise and take the bulb out from the bulbcover by turning it clockwise.
3. Replace with a new bulb. G270F02O
Bulb Cover
Power Code
1. Remove the mounting screws of the rear fog light cover with a phillips screwdriver.
G270F02A-GAT
Rear Fog Light
OCM055015L
4. To replace the rear combination light, take it out from the bulb holder byturning it counterclockwise.(1) Stop/Tail light (2) Back-up light (3) Turn signal light
5. Install the new bulb.
OCM055030
(1)
(2)
OCM055026(1)
(3)
CM-aust-6.p65
5/19/2008, 6:39 PM
33