Page 1057 of 1691

REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
12,000 MILE (19,000 KM) SEVERE DUTY SERVICE
12,000 MILE (19,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Brake Linings
Page 1058 of 1691

\
\
\
\
\
\
\
Water Pump Weep Hole For Blockage
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
Automatic Transmission Bands
\
\
\
\
\
\
\
Clean Fuel Strainer
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
Automatic Transmission Fluid & Filter
\
\
\
\
\
\
\
Rear Axle Fluid
\
\
\
\
\
\
\
Front Axle Fluid (4x4)
\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
Page 1059 of 1691

\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
Front Axle Model 216 6.8 Pts. (3.6L)
Lubricant
\
\
\
\
\
Model 248 7.6 Pts. (3.6L)
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
15,000 MILE (24,000 KM) SEVERE DUTY SERVICE
15,000 MILE (24,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Page 1060 of 1691

SERVICE
\b\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
18,000 MILE (29,000 KM) SEVERE DUTY SERVICE
18,000 MILE (29,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
Page 1061 of 1691

\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Drive Belts
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
Clean Fuel Strainer
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
Page 1062 of 1691

\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
21,000 MILE (34,000 KM) SEVERE DUTY SERVICE
21,000 MILE (34,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
Page 1063 of 1691

\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
\f
\
\
\
\
\
\
\
24,000 MILE (38,000 KM) SEVERE DUTY SERVICE
24,000 MILE (38,000 KM) SEVERE DUTY SERVICE\
\
\
\
\
\
\
VERIFY
\b\
\
\
\
\
\
\
Last Major Service Was Performed.
\
\
\
\
\
\
\
INSPECT
\b\
\
\
\
\
\
\
Exhaust System
\
\
\
\
\
\
\
Brake Hoses
\
\
\
\
\
\
\
Engine Coolant Level, Hoses & Clamps
\
\
\
\
\
\
\
Front Wheel Bearings (4x2)
\
\
\
\
\
\
\
Fan Hub
\
\
\
\
\
\
\
Damper
\
\
\
\
\
\
\
Water Pump Weep Hole for Blockage
\
\
\
\
\
\
\
Brake Linings
\
\
\
\
\
\
\
SERVICE
\b\
\
\
\
\
\
\
Rotate Tires
\
\
\
\
\
\
\
Lubricate Steering Linkage
\
\
\
\
\
\
\
Automatic Transmission Bands
\
\
\
\
\
\
\
Adjust Valve Lash Clearance
\
\
\
\
\
\
\
Clean Fuel Strainer
\
\
\
\
\
\
\
REPLACE
\b\
\
\
\
\
\
\
Engine Oil
\
\
\
\
\
\
\
Engine Oil Filter
\
\
\
\
\
\
\
Automatic Transmission Fluid & Filter
\
\
\
\
\
\
\
Rear Axle Fluid
\
\
\
\
\
\
\
Front Axle Fluid (4x4)
Page 1064 of 1691

\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\
\b\
\
\
\b\
\
\
Material Condition Specification
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Above 10 F SAE 15W-40
(
1) (-12 C) To Over 30 F (-1 C)
\
\
\
\
\
Ambient Temperature Less Than SAE 10W-30
0 F (-18 C) To Over 30 F(-1 C)
\
\
\
\
\
Ambient Temperature Less Than With Block Heater:
-10 F(-23 C) Up To 0 F (-18 C) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
Brake Fluid All DOT 3
\
\
\
\
\
\
\
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
\
\
\
\
\
\
\
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
(
1) - SAE 10W-30 engine oil is preferred. Use only API approved
oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
\
\
\
\
\
\
\
FLUID CAPACITIES
\
\b\
\
\
\b\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
Fluid 47RE: Dry Fill 17 Qts. (16L)