1999 DODGE RAM radio


A/C -H EA TE R S YSTE M

1999 D odge P ic ku p R 1500
1999 MANUAL A/C-HEATER SYSTEMS
CHRYSLER
Dakota, Durango & Ram Pickup
SPECIFICATIONS
SPECIFICATIONS








\









\









\









\









\









\









\







Application Specification
Compressor Type .............................. Sanden SD-7H15 7-Cyl.
Compressor Belt Tension ........................................ ( 1)
Refrigerant (R-134a) Capacity
With Rear A/C Unit ....................................... 30 ozs.
Without Rear A/C Unit .................................... 28 ozs.
System Oil Capacity
Dakota & Ram Pickup ................................. ( 2) 8.1 ozs.
Durango
With Rear A/C Unit ................................. ( 2) 8.0 ozs.
Without Rear A/C Unit .............................. ( 2) 5.5 ozs.
System Operating Pressures ( 3)
High Side ......................... 190-220 psi (13.4-15.5 kg/cm
)
Low Side .............................. 32-40 psi (2.2-2.8 kg/cm)
( 1) - Dynamic tensioner automatically adjusts belt. Tension is okay if
indicator is within marked limits on belt tensioner.
( 2) - Use SP-20 PAG refrigerant oil.
( 3) - Measured at ambient air temperature of 80
F (27C).








\









\









\









\









\









\









\







WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
CAUTION: When battery is disconnected, radio will go into anti-theft
protection mode. Obtain radio anti-theft protection code from
owner prior to servicing vehicle.
DESCRIPTION
These systems are a blend-air type. Outside air enters
through a cowl at base of the windshield and flows through a plenum
chamber into blower housing. Airflow velocity is controlled by blower
speed selector switch. Air flows across evaporator and is directed by
a blend-air door to go either through or by-pass the heater core.
On Dakota and Durango, temperature control cable operates
blend-air door and allows immediate control of outlet air temperature.
It also controls operation of recirculation door. On Ram Pickup,
temperature is regulated by a blend-air servo motor controlled from
A/C-heater control panel rotary temperature dial. On all models, mode
selector switch controls vacuum-operated doors to direct conditioned
air to selected outlets.
Durango may also be equipped with an optional rear A/C unit.
The rear A/C unit consists of a blower motor and evaporator. It will
only operate while the front A/C is on. The optional rear A/C-heater
unit is controlled using fan and temperature switches.

6) Remove glove box. Reach through glove box opening and
disconnect antenna coaxial cable connector. Disconnect blower motor
connector located above glove box opening, near support brace for A/C-
heater housing. Disconnect radio ground strap. Loosen instrument panel
roll down bracket bolts about 2 turns, located at lower corners on
both sides of instrument panel. Remove 5 screws across top of dash
panel at base of windshield, removing center screw last.
7) Roll down instrument panel and install a temporary support
hook that is about 18" (457 mm) in length. Install hook from center
hole in instrument panel to center hole of dash panel. Pull lower
instrument panel outward until both roll down bracket bolts are in
slotted roll down position. Instrument panel should now be supported
and away from firewall.
8) Disconnect 2 door harness connectors, located on a bracket
near right end of instrument panel. Disconnect blower motor resistor.
Disconnect temperature control cable from A/C-heater housing and
remove from housing. See Fig. 5. Disconnect demister duct flexible
hose from A/C-heater housing.
9) Ensure instrument panel is free and clear for removal.
With the aid of an assistant, remove temporary support hook. Lift
instrument panel off of roll down bracket bolts and remove from
vehicle.
10) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.
Removal & Installation (Ram Pickup)
1) Disable air bag system. See AIR BAG SYSTEM SAFETY article.
Disconnect negative battery cable. Drain cooling system. Remove left
and right kick panel trim. Remove 5 screws and knee bolster/steering
column cover. Remove hood release and parking brake release handle
screws from lower instrument panel support. Remove 6 screws and
instrument panel support. Disconnect air bag connector at lower left
corner of instrument panel.
2) Pull PRNDL cable and twist to remove from position arm.
Push tab on bottom of cable retainer upward, then squeeze sides to
remove retainer from column. Remove tilt lever (tilt column only).
Remove both upper and lower shrouds from column. Remove lower fixed
column shroud. Loosen multifunction switch connector screw. Screw will
remain in connector.
3) Remove remaining steering column electrical connectors.
Remove air bag wiring harness from steering column wiring trough.
Remove wiring trough from steering column. Remove 3 toe plate nuts and
washers.
4) Remove 2 nuts and washers attaching steering column
bracket to instrument panel steering column support bracket. Allow
column to lower and rest on seat. Remove 2 screws from bottom of Air
Bag Control Module (ACM) cover. Remove 4 screws holding ACM to
transmission tunnel.
5) Disconnect wiring at ACM. Disconnect instrument panel left
side wiring connectors. Remove screw holding brake release to bottom
of instrument panel. Disconnect instrument panel right side wiring
connectors, which includes 2 connectors attached to A/C-heater
assembly housing, courtesy light connector, antenna cable and 2 body
connectors. Disconnect vacuum harness from A/C-heater system.
6) Remove 5 screws holding instrument panel to dash. Loosen
lower instrument panel pivot bolts. Roll instrument panel downward.
Remove instrument panel from vehicle.
7) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.

ELE C TR IC AL C O M PO NEN T L O CATO R

1999 D odge P ic ku p R 1500
1999 ELECTRICAL COMPONENT LOCATION
Chrysler Motors Electrical Component Location
Dodge; Ram Pickup
SAFETY PRECAUTION
WARNING: When working on vehicles equipped with Supplemental Restraint
System (SRS), never apply electrical voltage to the system.
This could cause the SRS (air bag) to be deployed.
BUZZERS, RELAYS & TIMERS









\









\









\









\









\









\









\







Component Component Location








\









\









\









\









\









\









\







A/C Compressor Clutch Relay On power distribution center.
Automatic Shut Down Relay On power distribution center.
Blower Motor Relay On power distribution center.
Central Timer Module Left side of dash, inboard of
steering column opening.
Combination Flasher Left side of dash, on
junction block.
Engine Starter Motor Relay On power distribution center.
Fog Lamp Relay On power distribution center.
Fuel Heater Relay (Diesel) On power distribution center.
Fuel Pump Relay On power distribution center.
Horn Relay On power distribution center.
Intake Air Heater Relay No. 1
(Diesel) On left inner fender, below
left battery.
Intake Air Heater Relay No. 2
(Diesel) On left inner fender, below
left battery.
Quad High Beam Relay On power distribution center.
Radio Choke Relay Behind center of dash, on
support.
Security Relay On power distribution center.
Trailer Tow Relay On power distribution center.
Transmission Control Relay On power distribution center.
Wiper Motor Relay On power distribution center.









\









\









\









\









\









\









\

vacuum connector. Remove heater control panel. To install, reverse
removal procedure.
HEATER CORE
Removal & Installation
Remove heater assembly from vehicle. See HEATER ASSEMBLY.
Disable heater assembly and remove heater core.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting bolts for hood
release handle.
2) Remove steering column trim panel and support bracket. If
equipped, remove tilt steering column lever. Remove upper and lower
shrouds from steering column. Remove knee bolster. Unplug driver's
side air bag module. Loosen multifunction switch wiring harness
connector screw and disconnect from switch. Screw will remain in
connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining bolts. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors located
nearest to dash panel from junction block. Disconnect brake light
switch. If equipped, disconnect Rear Wheel Anti-Lock (RWAL) brake
module, located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of heater assembly housing. Disconnect Air Bag Control Module (ACM)
connector.
6) Remove glove box. Reach through glove box opening and
disconnect antenna coaxial cable. Disconnect blower motor connector
located above glove box opening, near support brace for heater
assembly housing. Disconnect radio ground strap. Loosen instrument
panel roll-own bracket bolts about 2 turns (bolts are located at lower
corners, on both sides of instrument panel). Remove 5 bolts across top
of dash panel, at base of windshield, removing center screw last.
7) Roll down instrument panel and install a temporary support
hook that is about 18" (457 mm) in length. Install hook from center
hole in instrument panel to center hole of dash panel. Pull lower
instrument panel outward until both roll-down bracket bolts are in
slotted roll-down position. Instrument panel should now be supported
and away from firewall.
8) Disconnect 2 body wiring harness connectors, located on a
bracket near right end of instrument panel. Disconnect blower motor
resistor. Disconnect temperature control cable from heater assembly
housing and remove from housing. Disconnect defrost duct flexible hose
from heater assembly housing.
9) Ensure all electrical and vacuum connectors are
disconnected and instrument panel is free and clear for removal. With
the aid of an assistant, remove temporary support hook. Lift
instrument panel off of roll-down bracket bolts and remove from
vehicle.
10) To install, reverse removal procedure. Ensure all wiring

and hoses are clear and not pinched. Adjusting temperature control
cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT . Tighten bolts and
nuts to specification. See TORQUE SPECIFICATIONS. Enable air bag
system. See AIR BAG SYSTEM SAFETY article.
Removal & Installation (Ram Pickup)
1) Disconnect negative battery cable. Ensure front wheels are
in a straight-ahead position and steering wheel is in LOCKED position.
Disable air bag system. See AIR BAG SYSTEM SAFETY article. Remove Air
Bag Control Module (ACM) and bracket from floor panel transmission
tunnel. Drain cooling system.
2) Remove left and right cowl side inner trim panels. Remove
knee bolster/steering column cover. Remove hood release and parking
brake release handle bolts from lower instrument panel support.
3) Disconnect driver's side air bag connector at lower left
corner of instrument panel. If equipped, disconnect overdrive lock-out
switch wiring harness connector from instrument panel wire harness
near instrument panel lower reinforcement.
4) Pull PRNDL cable and twist to remove from position arm.
Push tab on bottom of cable retainer upward, then squeeze sides to
remove retainer from column. If equipped, remove tilt lever. Remove
both upper and lower shrouds from column. Remove lower fixed column
shroud. Loosen multifunction switch connector screw. Screw will remain
in connector.
5) Ensure steering wheel is in LOCKED position. Remove
remaining steering column electrical connectors. Remove air bag wiring
harness from steering column wiring trough. Remove wiring trough from
steering column. Remove steering column as an assembly from vehicle.
6) From driver's side of instrument panel, disengage parking
brake release linkage rod from parking brake mechanism. Disconnect
instrument panel wiring harness from parking brake mechanism.
Disconnect 3 wiring harness bulkhead connectors located closest to
dash panel.
7) Disconnect instrument panel left side wiring harness
connectors. Remove screw from center of headlight and dash-to-
instrument panel (bulkhead) connector, and disconnect connector.
Disconnect instrument panel-to-door wiring harness. Disconnect
instrument panel to stoplight switch connector. Disconnect vacuum
harness for heater system.
8) If equipped with an Infinity sound system, disconnect
Infinity wiring harness connector from instrument panel harness
connector that is secured to bulkhead connector.
9) From passenger's side of instrument panel, disconnect
radio antenna coaxial cable connector. Loosen right and left
instrument panel roll-down bracket bolts about .50" (13 mm). Removing
center screw last, remove 5 bolts holding top of instrument panel to
top of dash panel.
10) Roll instrument panel downward and install a temporary
support hook to center hole of dash panel. Support hook should support
instrument panel in rolled-down position, about 18" (457 mm) away from\
dash panel. Disconnect remaining wiring harness connectors. With the
aid of an assistant, remove temporary hook and lift instrument panel
from vehicle.
11) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.
TEMPERATURE CONTROL CABLE R & I
Removal (Dakota & Durango)
Disconnect negative battery cable. Disconnect but DO NOT
remove instrument panel. See INSTRUMENT PANEL. Disconnect temperature

CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See AIR CONDITIONING SERVICE
article in GENERAL INFORMATION section.
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM
CAUTION: The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly
installed or high output radio transmitting equipment. Since
this interference could cause the possible loss of the
antilock braking capability, such equipment should be
installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
AUTOMATIC TRANSAXLE FLUID SERVICE
WARNING: Make certain no fluid is spilled when the transaxle fluid
is inspected. Wipe up any spilled fluid completely.
AXLE FLUID
CAUTION: Axle lubricant should be changed whenever the axle has

F1 - Not Used
F2 - 30 Amp (Lt. Green)
Blower Motor
CB1 - 30 Amp (Circuit Breaker)
Power Windows
CB2 - 30 Amp (Circuit Breaker)
Power Seats
1 - 20 Amp (Yellow)
Power Outlet
2 - Not Used
3 - Not Used
4 - Not Used
5 - 20 Amp (Yellow)
Cigar Lighter
6 - 20 Amp (Yellow)
Turn Signal Flasher
7 - 15 Amp (Lt. Blue)
Radio
8 - 20 Amp (Yellow)
Windshield Wipers
9 - 10 Amp (Red)
Fuel Pump Relay, A/C Compressor Clutch Relay
Automatic Shutdown Relay, Transmission Overdrive
Solenoid, EGR Solenoid, Powertrain Control Module (PCM)
Ignition Module
High Pressure Fuel Shut-Off Solenoid Relay (CNG Models Only)
EGR Solenoid (CNG Models Only)
10 - Not Used
Vehicle Speed Control
11 - 10 Amp (Red)
Buzzer, Overhead Console
12 - 15 Amp (Lt. Blue)
Airbag Diagnostic Module, Cluster, Message Center,
13 - 5 Amp (Tan)
Illumination
14 - 20 Amp (Yellow)
RWAL and ABS Module
15 - 15 Amp (Lt. Blue)
Automatic Day/Night Mirror, Back-up Lights,
Daytime Running Lamps
16 - 15 Amp (Lt. Blue)
Airbag Diagnostic Module
17 - 15 Amp (Lt. Blue)
Ignition Off Draw, Radio and Clock Memory
18 - 15 Amp (Lt. Blue)
Parking Lamps
19 - 20 Amp (Yellow)
Power Door Locks
20 - 15 Amp (Lt. Blue)
Stop Lamps
POWER DISTRIBUTION CENTER

PA R ASIT IC L O AD E XPLA N ATIO N & T E ST P R O CED URES

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Parasitic Load Explanation & Test Procedures
* PLEASE READ THIS FIRST *
This article is provided for general information only. Not
all procedures apply to all makes and models.
GENERAL INFORMATION
The term Parasitic Load refers to electrical devices that
continue to use or draw current after the ignition switch is turned to
OFF position. This small amount of continuous battery draw is
expressed in milliamps (mA). On Ford Motor Co. and General Motors
vehicles produced after 1980, a typical Parasitic Load should be no
more than 50 milliamps (0.050 amps).
Vehicles produced since 1980 have memory devices that draw
current with ignition off for as long as 20 minutes before shutting
down the Parasitic Drain. When Parasitic Load exceeds normal
specifications, the vehicle may exhibit dead battery and no-start
condition.
Follow test procedure for checking Parasitic Loads to
completion. A brief overview of a suggested test procedure is included
along with some typical Parasitic Load specifications. Refer to the
GENERAL MOTORS PARASITIC LOAD TABLE chart.
TESTING FOR PARASITIC LOAD
INTRODUCTION
CAUTION: Always turn ignition off when connecting or disconnecting
battery cables, battery chargers or jumper cables. DO NOT
turn test switch to OFF position (which causes current to run
through ammeter or vehicle electrical system).
NOTE: Memory functions of various accessories must be reset after
the battery is reconnected.
The battery circuit must be opened to connect test switch
(shunt) and ammeter into the circuit. When a battery cable is removed,\
timer circuits within the vehicle computer are interrupted and
immediately begin to discharge. If in doubt about the condition of the
ammeter fuse, test it with an ohmmeter prior to beginning test. An
open fuse will show the same reading (00.00) as no parasitic drain.
Begin test sequence with the meter installed and on the 10-amp scale.
Select lower scale to read parasitic draw.
TEST PROCEDURE USING TEST SWITCH
1) Turn ignition off. Remove negative battery terminal cable.
Install Disconnect Tool (J-38758) test switch male end to negative
battery cable. Turn test switch knob to OFF position (current through
meter). Install negative battery cable to the female end of test
switch.
2) Turn test switch knob to ON position (current through
switch). Road test vehicle with vehicle accessories on (radio, air
conditioner, etc.). After road test, turn ignition switch to LOCKED
position and remove key. Connect ammeter terminals to test switch