1999 DODGE RAM check transmission fluid

stretched, cut or pinched wiring. Ensure electrical connectors fit
tightly and are not corroded. Check PCM, sensors and switches for
physical damage. Check engine coolant level. Check transmission fluid
level and condition.
SELF-DIAGNOSTIC SYSTEM
* PLEASE READ THIS FIRST *
NOTE: Only transaxle-related trouble codes are listed. For engine-
related DTC definitions, see TROUBLE CODE DEFINITIONS article
in APPLICATIONS & IDENTIFICATION. For engine-related DTC
diagnosis, see appropriate SELF-DIAGNOSTICS article in ENGINE
PERFORMANCE. Engine performance DTCs must be repaired first,
as engine performance and related component signals will
affect transaxle operation and diagnosis.
DIAGNOSTIC PROCEDURE
When performing vehicle diagnosis:
* Ensure transmission fluid level is correct and fluid is
neither contaminated or aerated.
* Ensure shift cable is properly adjusted. See appropriate
AUTOMATIC TRANSMISSION SERVICING article in TRANSMISSION
SERVICING.
* Ensure battery is fully charged.
* Perform visual inspection, ensuring all electrical
connections at transmission, PCM, TP sensor and output shaft
speed sensor are clean and properly installed.
* Retrieve DTCs. See RETRIEVING DIAGNOSTIC TROUBLE CODES.
* Repair DTCs in order displayed.
* Always perform test verification test after any repair
procedure is completed unless specified otherwise. See
appropriate verification test under DIAGNOSTIC TESTS.
NOTE: Self-diagnostic tests are written specifically for Chrysler's
Diagnostic Readout Box (DRB) scan tool. A generic scan tool
may be used, but may not be capable of performing all
necessary test functions.
TEST EQUIPMENT HOOK-UP
Generic Scan Tool & DVOM
Self-diagnostic tests are written specifically for Chrysler's
Diagnostic Readout Box (DRB) scan tool. The DRB has a built-in DVOM
function. A generic scan tool may be used, but may not be capable of
performing all necessary test functions. If DRB test procedures
require resistance or voltage to be measured using scan tool in
ohmmeter or voltmeter mode, connect DVOM ground lead to DLC connector
terminal No. 4 and positive lead to terminal specified in test
procedure.
DRB Scan Tool
Refer to DRB scan tool instructions to read and clear DTCs,
and when performing other scan tool functions. DRB scan tool is
grounded through DLC connector terminal No. 4. Only one volt/ohmmeter
test lead is required to measure voltage or resistance. See Fig. 2.
RETRIEVING DIAGNOSTIC TROUBLE CODES
NOTE: Manufacturer recommends using Chrysler's Diagnostic Readout

2) If any DTCs listed are present, perform appropriate
test(s). See TORQUE CONVERTOR CLUTCH (TCC) TESTS table. If no DTCs a\
re
present, go to next step.
TORQUE CONVERTOR CLUTCH (TCC) TESTS









\









\









\









\









\









\









\







DTC DTC Message
P0122 (1) ................. THROTTLE POSITION SENSOR VOLTAGE TOO LOW
P0123 ( 1) ................ THROTTLE POSITION SENSOR VOLTAGE TOO HIGH
P1696 ( 1) .......................... PCM FAILURE EEPROM WRITE DENIED
P0743 ........ TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS
( 2) ........................................................ MISFIRE
P0320 ( 1) ......................... NO CRANK REFERENCE SIGNAL AT PCM
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.
( 2) - Perform appropriate misfire DTC test. See appropriate
SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Start engine. Using scan tool, perform TCC SYSTEM TEST. If
vehicle does not stall, go to step 9). If vehicle stalls, go to next
step.
5) Using scan tool, perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If vehicle stalls, go to next step. If vehicle
does not stall, go to step 7).
6) Turn ignition off. Replace TCC solenoid. Using scan tool,
perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
vehicle stalls, problem in internal. Check for blocked passage. If
vehicle does not stall, testing is complete.
7) Turn ignition off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
8) Inspect all related wiring and connectors. Repair as
necessary. If wiring and connectors are okay, see INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
9) Turn ignition off. Connect a pressure gauge to
transmission cooler OUT port. Start engine. Using scan tool, perform
TCC SYSTEM TEST. If pressure increases when TCC is actuated, go to
next step. If pressure does not increase, repair leaks or blockage in
hydraulic circuit, or repair valve body as necessary.
10) Turn engine off. Remove oil pump and inspect reaction
shaft, input shaft and input seal. Repair transmission as necessary.
See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, there are no other potential causes remaining.
TCC is assumed to be defective. Replace torque converter.
DTC P0743: TORQUE CONV CLUTCH SOLENOID/TRANS RELAY CKT
NOTE: To test transmission temperature sensor, engine and
transmission temperature must be less than 85F (29C).
Circuit Description
Circuit is monitored continuously while key is on. Code sets
if voltage detected on Torque Converter Clutch (TCC) at the Powertrain\
Control Module (PCM) does not match desired voltage.
Possible Causes

replace PCM and see INACTIVE DTC CONDITION under SELF-DIAGNOSTIC
SYSTEM. Testing is complete.
DTC P0783: 3-4 SHIFT SOL, NO RPM DROP @ 3-4 SHIFT
Circuit Description
Circuit is monitored continuously while key is on and engine
running. Code sets if expected RPM drop does not occur within 4
seconds of requested gear change by PCM. Test must fail 3 times to set
code.
Possible Causes
* Transmission mechanically defective.
* TPS codes set.
* Transmission 3-4 solenoid wiring harness defective.
* Transmission fluid burnt or oil pan has excessive debris.
Diagnostic Procedures
1) Using scan tool, read DTCs. On all bodies except AB and WJ
bodies, go to next step. On AB and WJ bodies, if DTC SPECIFIC GOOD
TRIPS counter is not displayed or displayed count is not "0", go to
step 6). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", indicating DTC still exists, go to next step.
2) If any DTCs listed are present, perform appropriate
test(s). See 3-4 SHIFT SOLENOID TESTS table. If no DTCs are present,
go to next step.
3-4 SHIFT SOLENOID TESTS









\









\









\









\









\









\









\







DTC Message Test
NO CAM SIGNAL AT PCM ..................................... ( 1) P0340
P/N SWITCH STUCK IN PARK OR IN GEAR .......................... P1899
Any Throttle Position Sensor (TPS) DTC ......................... ( 1)
TORQUE CONVERTOR CLUTCH SOLENOID/TRANS RELAY CIRCUITS ........ P0743
TRANS 12-VOLT SUPPLY RELAY CNTRL CIRCUIT ..................... P1765
TRANS 3-4 SHIFT SOLENOID/TRANS RELAY CIRCUITS ................ P0753
( 1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.









\









\









\









\









\









\









\







3) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
4) Connect a 0-300 psi (0-21 kg/cm
) pressure gauge to
transmission Overdrive (O/D) clutch pressure test port. Connect a
second 0-300 psi (0-21 kg/cm
) pressure gauge to transmission governor
pressure test port. See appropriate AUTOMATIC TRANSMISSION OVERHAUL
article. Ensure engine and transmission are at normal operating
temperature. With an assistant, test drive vehicle. Using scan tool,
select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear while
monitoring pressure gauge. Governor pressure should rise to greater
than 20 psi (1.4 kg/cm
) and O/D pressure should rise to greater than
40 psi (2.8 kg/cm). If pressures are as specified, go to next step.
If pressures are not as specified, go to step 8).
5) Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, go to next step.
6) Using scan tool, erase DTCs. Start engine. Road test
vehicle at 0-55 MPH with a constant 20 percent throttle. Repeat road
test 4 times. Note if DTC P0783 resets. If DTC P0783 resets, repair
wiring harness as necessary. If DTC P0783 does not reset, go to next

(1) - See appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE.








\









\









\









\









\









\









\







3) Ensure fuel tank is at least 1/4 full. If fuel level is
too low, correct fuel level and retest. If fuel level is okay, go to
next step.
4) Ensure transfer case is not in low range. Shift transfer
case out of low range. If transfer case is not in low range, go to
next step.
5) Ensure PTO is not engaged. Disengage PTO. If PTO is not
engaged, go to next step.
6) Ensure transmission fluid temperature is above 32
F (0C).
Warm transmission to normal operating temperature. If transmission
fluid temperature is above 32
F (0C), go to next step.
7) Turn ignition on. Using scan tool, build a custom display
with engine RPM, output shaft SPD, TCC solenoid, O/D solenoid and
throttle position. Set overdrive to off position. Road test vehicle
and reach a steady speed of 55 MPH with a minimum throttle opening
voltage of 1.15 volts for 20 seconds. Note shift patterns while
vehicle is attaining speed. If engine RPM is within 60 RPM of output
shaft speed RPM, go to next step. If engine RPM is not within 60 RPM
of output shaft speed RPM, go to step 15).
8) If output shaft speed RPM is greater than engine RPM, go
to next step. If output shaft speed RPM is equal to or less than
engine RPM, go to step 15).
9) Road test vehicle and reach a steady speed of 55 MPH and
engage overdrive. If engine RPM is 69 percent of output shaft speed,
go to step 15). If engine RPM is not 69 percent of output shaft speed,
go to next step.
10) Connect a 0-300 psi (0-21 kg/cm
) pressure gauge to
transmission Overdrive (O/D) clutch pressure test port. Connect a
second 0-300 psi (0-21 kg/cm
) pressure gauge to transmission governor
pressure test port. See appropriate AUTOMATIC TRANSMISSION OVERHAUL
article. Ensure engine and transmission are at normal operating
temperature. With an assistant, test drive vehicle. Using scan tool,
select GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear while
monitoring pressure gauge. Governor pressure should rise to greater
than 20 psi (1.4 kg/cm
) and O/D pressure should rise to greater than
40 psi (2.8 kg/cm). If pressures are as specified, go to next step.
If pressures are not as specified, go to step 13).
11) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
12) Drain transmission fluid and remove oil pan. If
transmission fluid is burnt or has excessive debris, repair as
necessary. If transmission fluid is okay, go to step 23).
13) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
14) Leave gauges connected. Replace 3-4 shift solenoid. Start
engine and allow engine and transmission to reach normal operating
temperature. Using scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear while monitoring pressure gauges. Governor
pressure should rise to greater than 20 psi (1.4 kg/cm
) and O/D
pressure should rise to greater than 40 psi (2.8 kg/cm). If pressures
are as specified, testing is complete. If pressures are not as
specified, see appropriate AUTOMATIC TRANSMISSION OVERHAUL article,
paying attention to seals and clutches related to O/D clutch.
15) Check transmission fluid for proper level and for any
debris. Fill or repair transmission as necessary. If fluid level and
condition are okay, go to next step.
16) Start engine. Using scan tool, perform TCC SYSTEM TEST.

If engine stalls, go to next step. If engine does not stall, go to
step 19).
17) Using scan tool, select GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If engine stalls, go to next step. If engine
does not stall, go to step 23).
18) Replace TCC solenoid. Perform GOV and 3-4 SHIFT VALVE
SYSTEM TEST. Select 4th gear. If engine stalls, repair internal
problem. Check for internally blocked passages. See appropriate
AUTOMATIC TRANSMISSION OVERHAUL article. If engine does not stall,
test is complete.
19) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and go to next step. If all parts are okay, replace torque
converter.
20) Start engine. Perform GOV and 3-4 SHIFT VALVE SYSTEM
TEST. Select 4th gear. If engine stalls, go to next step. If engine
does not stall, go to step 23).
21) Turn ignition off. Replace TCC solenoid. Start engine.
Perform GOV and 3-4 SHIFT VALVE SYSTEM TEST. Select 4th gear. If
engine stalls, repair internal problem. Check for internally blocked
passages. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
engine does not stall, go to next step.
22) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and replace torque converter. If all parts are okay, test is
complete.
23) Turn ignition off. Remove oil pump. Inspect reaction
shaft, input shaft and input seal. If any parts are damaged, repair as
necessary and replace torque converter. If all parts are okay, go to
next step.
24) Record freeze frame data to determine conditions when
code was set. Using wiring diagram as a guide, inspect wiring and
connectors. Repair wiring harness as necessary. If wiring and
connectors are okay, go to next step.
25) Using scan tool, erase DTCs. Start engine. Attempt to
duplicate data and reset code. Road test vehicle maintaining a
constant throttle opening voltage of 1.15 volts, reach a speed of 60
MPH. Repeat road test 4 times. Note if DTC P1740 resets. If DTC P1740
resets, there are no other possible causes remaining. Problem is
considered to be an intermittent problem in wiring harness connector
or wire. See INACTIVE DTC CONDITION under SELF-DIAGNOSTIC SYSTEM.
Repair wiring harness as necessary. If DTC P1740 does not reset,
testing is complete.
DTC P1756: GOV PRESS NOT EQUAL TO TARGET @ 15-20 PSI
Circuit Description
Circuit is monitored continuously while key is on and engine
running, not in Park or Neutral position or with Malfunction Indicator
Light (MIL) illuminated. Code sets if governor pressure sensor output
is not 15-30 psi (1.0-2.1 kg/cm
) when requested pressure is 20-25 psi
(1.4-1.7 kg/cm) for 2.2 seconds. Test must fail 5 times to set code.
Possible Causes
* Other transmission codes are set.
* Solenoid pack connector 5 volt supply circuit open.
* Governor pressure sensor defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Governor pressure out of range.
* Transmission leaking internally.
Diagnostic Procedures

as necessary. If connector and terminals are okay, turn ignition on.
Measure voltage between ground and 5-volt supply circuit at
transmission solenoid harness connector. If voltage is 4.5 volts or
less, repair open 5-volt supply circuit. If voltage is greater than 4.
5 volts, replace governor pressure sensor.
13) Turn engine off. Install transmission control relay.
Drain transmission fluid and remove oil pan. Inspect pan for burnt oil
and debris. Repair transmission as necessary. See appropriate
AUTOMATIC TRANSMISSION OVERHAUL article. If transmission is okay, go
to next step.
14) Replace governor pressure solenoid. Replace transmission
oil pan and refill fluid. Start engine. Remove transmission control
relay. Depress brake pedal and place gear selector in "D" position.
Read gauge pressure. If pressure is 40-55 psi (2.8-3.9 kg/cm
),
testing is complete. If pressure is not as specified, replace valve
body.
15) Conditions required to set DTC P1756 are not present at
this time. Using scan tool, clear DTCs. Start engine and check for
DTCs. Wiggle wiring harness between governor pressure sensor and PCM.
Note if DTC P1756 resets. If DTC P1756 resets, repair wiring harness
as necessary. If DTC P1756 does not reset, see INACTIVE DTC CONDITION
under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P1757: GOV PRES ABOVE 3 PSI IN GEAR WITH 0 MPH
Circuit Description
Circuit is monitored continuously while key is on and engine
running, not in Park or Neutral position or with Malfunction Indicator
Light (MIL) illuminated. Code sets if governor pressure sensor is
greater than 3 psi (.2 kg/cm
) when requested pressure is zero with
governor pressure solenoid duty cycle at 95 percent for 2.65 seconds.
Test must fail twice to set code.
Possible Causes
* Other transmission codes are set.
* Solenoid pack connector 5-volt supply circuit open.
* Governor pressure sensor defective.
* Wiring harness and/or connectors defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Valve body defective.
Diagnostic Procedures
1) Using scan tool, read DTCs. On AN and DN bodies, go to
next step. On all except AN and DN bodies, if DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step 8).
If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed count is
"0", go to next step.
2) Repair any other transmission related DTCs before
proceeding. If no other transmission related DTCs exist, go to next
step.
3) Start engine. Allow engine to reach normal operating
temperature. Set parking brake, depress brake pedal and place gear
selector in "D" position. Using scan tool, read governor pressure
sensor value. If value is greater than 3 psi (.2 kg/cm
), go to next
step. If value is 3 psi (.2 kg/cm) or less, go to step 8).
4) Turn ignition off. Install a pressure gauge at governor
pressure test port. See TESTING in appropriate AUTOMATIC TRANSMISSION
OVERHAUL article. Start engine. With gear selector in "D" position,
read gauge pressure. If pressure is less than 3 psi (.2 kg/cm
), go to
step 7). If pressure is 3 psi (.2 kg/cm) or greater, go to next step.
5) Turn engine off. Drain transmission fluid and remove oil
pan. Inspect oil pan for burnt oil and debris. Repair transmission as

necessary. See appropriate AUTOMATIC TRANSMISSION OVERHAUL article. If
transmission is okay, go to next step.
6) Replace governor pressure solenoid. Replace transmission
oil pan and refill fluid. Start engine. Read gauge pressure. If
pressure is less than 3 psi (.2 kg/cm
), testing is complete. If
pressure is 3 psi (.2 kg/cm) or greater, replace valve body.
7) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair
as necessary. If connector and terminals are okay, turn ignition on.
Measure voltage between ground and 5-volt supply circuit at
transmission solenoid harness connector. If voltage is 4.5 volts or
less, repair open 5-volt supply circuit. If voltage is greater than 4.
5 volts, replace governor pressure sensor.
8) Using scan tool, read and record FREEZE FRAME data. Ensure
CAUSED BY DTC hex code matches DTC message on screen. Using wiring
diagram as a guide, inspect wiring and connectors. Repair wiring
harness as necessary. If wiring and connectors are okay, go to next
step.
9) Using scan tool, clear DTCs. Drive vehicle at 0-20 MPH and
come to complete for 20 seconds. Repeat road test 5 times. Using scan
tool, monitor governor actual pressure and target pressure. If
pressures greater than 3 psi (.2 kg/cm
) at zero MPH appears, repair
wiring harness as necessary. If pressures greater than 3 psi (.2
kg/cm
) at zero MPH do not appear, testing is complete.
DTC P1762: GOV PRESS SEN OFFSET VOLTS TOO LOW OR HIGH
Circuit Description
Circuit is monitored continuously while key is on and engine
running. Code sets if governor pressure is out of range for 1.3
seconds. Test must fail 3 times to set code.
Possible Causes
* Solenoid pack connector 5 volt supply circuit open.
* Governor pressure sensor ground circuit open.
* Governor pressure sensor wiring harness and/or connectors
defective.
* Transmission fluid burnt or oil pan has excessive debris.
Diagnostic Procedures
1) Using scan tool, read DTCs. On AN and DN bodies, go to
next step. On all except AN and DN bodies, if DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step 9).
If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed count is
"0", go to next step.
2) Start engine and allow it to reach normal temperature.
Check transmission fluid level and condition. Correct transmission
fluid level or condition as necessary. If transmission fluid level and
condition are okay, go to next step.
3) Turn ignition off and back on. Do not start. Using scan
tool, check Park/Neutral Position (PNP) switch operation. Repair PNP
switch as necessary. If PNP switch operation is okay, go to next step.
4) Start engine. Place gear selector in Neutral. Using scan
tool, read GOV PRESSURE voltage. If voltage is not .30-.76 volt, go to
step 6). If voltage is as specified, go to next step.
5) While monitoring GOV PRESSURE sensor voltage, wiggle
connectors and wiring harness between governor pressure sensor and
PCM. If voltage changes while wiggling connectors and harness, repair
connector or harness as necessary. If voltage does not change,
conditions required to set DTC P1762 are not present at this time. DTC
P1762 sets if governor pressure sensor input is less than or greater
than a predetermined PNP switch calibration for 1.3 seconds under

10) If governor pressure voltage is than .12-.80 volt, go to
next step. If governor pressure voltage is .80 volt or greater, go to
test DTC P1763B: GOVERNOR PRESSURE SENSOR VOLTS TOO HIGH (AN & DN
BODIES).
11) Wiggle wiring harness between PCM and governor pressure
sensor while monitoring governor pressure voltage on scan tool. If
voltage changes while wiggling wiring harness, repair wiring harness
as necessary. If voltage does not change, conditions required to set
DTC P1764 are not present at this time. DTC P1764 sets if governor
pressure sensor input is less than .1 volt for 8.5 seconds. Possible
causes are: PCM internally shorted or open, incorrectly wired, dirty
or corroded connectors or open or shorted wiring. See INACTIVE DTC
CONDITION under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
Diagnostic Procedures (BR Body)
1) Using scan tool, read DTCs. If DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step
23). If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed
count is "0", go to next step.
2) Turn ignition off. Disconnect transmission solenoid
harness connector. Inspect connector and terminals for damage. Repair
as necessary. If connector and terminals are okay, turn ignition on.
Measure voltage between ground and 5-volt supply circuit at
transmission solenoid harness connector. If voltage is 4.5-5.5 volts,
go to next step. If voltage is not as specified, repair open 5-volt
supply circuit.
3) Reconnect transmission solenoid harness connector. Using
scan tool, read governor pressure sensor voltage. If voltage is
greater than 4.65 volts, go to step 9). If voltage is less than .12
volt, go to next step. If voltage is not .12-.80 volt, go to step 23).
If voltage is .80-4.65 volts, go to step 16).
4) Check and record freeze frame data to determine conditions
which set code. Turn ignition off. Disconnect PCM harness connectors.
Disconnect transmission solenoid harness connector. Inspect connector
and terminals for damage. Repair as necessary. If connector and
terminals are okay, measure resistance between sensor ground circuit
at Black PCM harness connector C1 and governor pressure sensor signal
circuit at White PCM harness connector C2. If resistance is less than
5 ohms, repair governor pressure sensor signal circuit for short to
ground circuit. If resistance is 5 ohms or greater, go to next step.
5) Measure resistance between ground and governor pressure
sensor signal circuit at White PCM harness connector C2. If resistance
is less than 5 ohms, repair governor pressure sensor signal circuit
for short to ground. If resistance is 5 ohms or greater, go to next
step.
6) Drain transmission fluid and remove oil pan. Disconnect
pressure/temperature sensor harness connector. Inspect connector and
terminals for damage. Repair as necessary. If connector and terminals
are okay, reconnect transmission solenoid harness connector. Measure
resistance between ground circuit and governor pressure sensor signal
circuit at governor pressure sensor harness connector. If resistance
is less than 5 ohms, repair or replace transmission solenoid and
harness assembly. If resistance is 5 ohms or greater, go to next step.
7) Measure resistance between ground and governor pressure
sensor signal circuit at governor pressure sensor harness connector.
If resistance is less than 5 ohms, repair or replace transmission
solenoid and harness assembly. If resistance is 5 ohms or greater, go
to next step.
8) Reconnect all harness connectors except
pressure/temperature sensor harness connector. Turn ignition on. Using
scan tool, read governor pressure sensor voltage. If voltage is 4.8
volts or less, replace PCM. If voltage is greater than 4.8 volts,
replace pressure/temperature sensor.