1999 DODGE RAM brake light

"R" ABBREVIATION TABLE

"R" ABBREVIATION TABLE
ABBREVIATION DEFINITION RABS Rear Anti-Lock Brake System RAC Remote Accessory Control RAM Random Access Memory RAP Retained Accessory Power RECIRC Recirculation RED Red RH Right hand ROM Read Only Memory RPM Revolutions Per Minute RVB Rear Vacuum Break RWAL Rear Wheel Anti-Lock Brake RWD Rear Wheel Drive Recirc. Recirculate or Recirculation Reg. Regulator Rly. Relay

"S" ABBREVIATION TABLE

"S" ABBREVIATION TABLE
ABBREVIATION DEFINITION SAW Spark Angle Word _ SBC Single Bed Converter _ SBEC Single Board Engine Controller _ SC Super Charged _ SCC Spark Control Computer _ SCS Air Suction Control Solenoid _ SDM Supplemental Restraint System Diagnostic Module _ SDU SRS Diagnostic Unit _ SEN Sensor _ SES Service Engine Soon _ SFI Sequential (Port) Fuel Injection _ SIG RTN Signal Return circuit _ SIL Shift Indicator Light _ SIR Supplemental Inflatable Restraint _ SMEC Single Module Engine Controller _ SOHC Single Overhead Cam _ SOL or SoL Solenoid _ SPFI Sequential Port Fuel Injection _ SPK Spark Control _ SPOUT Spark Output Signal _ SRS Supplemental Restraint System (Air Bag) _ SS 3/4-4/3 Shift Solenoid circuit _ SSI Solid State Ignition _ STAR Self-Test Automatic Readout _ STI Self Test Input circuit _ STO Self-Test Output _ SUB-O2 Sub Oxygen Sensor _ Sen. Or Sens. Sensor _ Sol. Solenoid _ Sprchg. Supercharger _ Strg. Steering _ Susp. Suspension _ Sw. Switch _ Sys. System _

knob pointer) is flush with base of A/C-heater control panel.
5) Rotate temperature control knob to its full clockwise
stop. Release knob. Knob pointer should be aimed at end of Red stripe.
If knob is pointed at end of Red stripe, go to next step. If knob is
not pointed at end of Red stripe, go back to step 2) and repeat
adjustment procedure.
6) Rotate temperature control knob to its full
counterclockwise stop. Release knob. If knob springs back, self-
adjuster clip securing temperature control cable to blend-air door
lever is improperly installed. See TEMPERATURE CONTROL CABLE R & I. If
knob does not spring back, temperature control cable adjustment is
complete.
TESTING
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG SYSTEM SAFETY
article.
A/C-HEATER CONTROL PANEL TEST
1) Connect a vacuum gauge in line with Black A/C-heater
vacuum supply hose, located at tee near power brake booster (Dakota)
or in engine compartment (Durango and Ram Pickup). Position gauge so
it can be viewed from passenger compartment.
2) Start engine. While observing gauge, rotate mode control
knob to each mode position (one position at a time). Pause after each
selection. Test gauge should drop, then return to 8 in. Hg shortly
after each selection is made. If gauge reading is as specified, go to
next step. If gauge reading is not as specified, check for vacuum leak
in vacuum lines or A/C-heater control panel.
3) Move temperature control knob quickly to full hot and full
cold positions. A distinct sound of blend-air door hitting its stops
should be heard. No spring-back of knob should exist.
4) If temperature control knob operates as specified,
temperature control system is okay. On Dakota and Durango, if
temperature control knob does not operate as specified, check
condition, routing, installation, and adjustment of temperature
control cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT . Also check
blend air door for proper installation, obstructions, or faulty seals.
A/C SYSTEM PERFORMANCE
1) Park vehicle out of direct sunlight. Ensure ambient
temperature is at least 70F (21C). Connect tachometer and manifold
gauge set to vehicle. Turn A/C on. Turn mode control to panel and
recirculated air positions, temperature control lever to maximum
cooling, and blower to high.
2) Start engine and allow it to run at 1000 RPM, with A/C
compressor clutch engaged. Engine should be at operating temperature
with doors, windows, and hood closed. Insert thermometer into left
center air outlet.
3) Run engine and operate system for 5 minutes. The A/C
compressor clutch may cycle, depending on temperature. If A/C
compressor clutch cycles, stop engine and disconnect negative battery
cable. Remove clutch cycling pressure switch connector. Place a jumper
wire across terminals of clutch cycling pressure switch harness
connector.
4) Connect negative battery cable. Turn A/C on. Start and

assembly towards right side of vehicle and remove rear A/C-heater
assembly.
5) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS .
Removal (Ram Pickup - Front)
1) Disconnect negative battery cable. Drain cooling system.
In engine compartment, remove coolant hoses from heater core tubes.
Remove coolant overflow bottle.
2) Discharge A/C system, using approved refrigerant
recovery/recycling equipment. Disconnect refrigerant lines from
evaporator and plug or cover all openings in A/C system. Remove
instrument panel. See INSTRUMENT PANEL. Remove Powertrain Control
Module (PCM) and position aside. DO NOT disconnect 60-pin connector
from PCM.
3) Remove attaching nuts from studs on engine compartment
side of dash panel. Remove defrost duct. Disconnect electrical
connectors. Remove attaching nuts from studs in passenger compartment
side of dash panel. Remove A/C-heater assembly from vehicle. See
Fig. 5 .
4) Place A/C-heater assembly upside-down on work bench.
Remove screw securing floor duct to bottom of A/C-heater assembly and
slide floor duct off of center heat duct adapter. Unsnap center heat
duct adapter from bottom of A/C-heater assembly housing. Remove screw
hidden behind adapter. Remove remaining screws and separate A/C-heater
assembly.
Installation
Ensure mode door pivot pins are properly inserted in holes.
To complete installation, reverse removal procedure.
A/C-HEATER CONTROL PANEL R & I
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. On models equipped with
A/T, unlock ignition switch. Set parking brake and place gear selector
lever in "L" position. If equipped, set tilt steering column in lowest
position.
2) On all models, carefully pry bezel away from instrument
panel to disengage clips. Unplug connectors from cigarette lighter and
auxiliary power outlet. Disconnect fog light switch (if equipped).
Remove A/C-heater control panel screws.
3) Pull control panel outward enough to disconnect wiring
connector, vacuum harness, and temperature control cable. Remove A/C-
heater control panel. To install, reverse removal procedure. Adjust
temperature control cable. See TEMPERATURE CONTROL CABLE ADJUSTMENT .
Removal & Installation (Ram Pickup)
1) Disconnect negative battery cable. Reach under driver's
side of instrument panel, near transmission tunnel and unplug A/C-
heater control panel to A/C-heater assembly vacuum harness connector.
Disconnect vacuum harness from center air duct.
2) On models equipped with A/T, unlock ignition switch. Set
parking brake and place gear selector lever in "L" position. If
equipped, set tilt steering column in lowest position.
3) On all models, remove screw securing cluster bezel to
instrument panel. See Fig. 6. Carefully pry bezel away from instrument
panel to disengage clips. Unplug connectors from cigarette lighter and
auxiliary power outlet.
4) Remove 4 screws attaching A/C-heater control panel. Pull
control panel outward enough to disconnect wiring connector, vacuum
harness and temperature control cable. Remove A/C-heater control

from housing. To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system.
Removal & Installation (Durango - Rear Evaporator Core)
1) Disconnect negative battery cable. Discharge A/C system,
using approved refrigerant recovery/recycling equipment. Remove
headliner from passenger compartment of vehicle. Remove sun visors and
sun visor arm supports.
2) Remove coat hooks, overhead assist handle and dome light.
If equipped, remove overhead console. Remove air outlet bezel from
rear A/C-heater assembly. Remove rear blower motor switch. Remove
upper liftgate opening trim. Disengage "A", "B", "C", and "D" pillar
trim as necessary to prevent trim panel interference.
3) Move second and third row seats to cargo position. Move
front seats to full recline position. Remove headliner fasteners.
Carefully bow headliner and remove through lift gate opening.
4) Disconnect "B" pillar drain hoses from "Y" fittings.
Disconnect "B" pillar refrigerant lines and plug or cover all openings
in A/C system. Remove lower A/C-heater assembly cover. Remove screws
securing refrigerant tube and retaining strap to right side of upper
housing cover. Remove evaporator core. To install, reverse removal
procedure. Install new "O" rings to A/C fittings. Evacuate and charge
A/C system.
Removal & Installation (Ram Pickup - Front)
1) Remove and disassemble A/C-heater housing. See
A/C-HEATER ASSEMBLY . Separate halves of A/C-heater housing and remove
top half. Remove evaporator or heater core from housing.
2) To install, reverse removal procedure. Install new "O"
rings to A/C fittings. Evacuate and charge A/C system. Fill cooling
system. On 5.9L diesel engine, engine is equipped with a one-way check
valve. DO NOT run engine while filling cooling system. Fill engine
with engine turned off.
INSTRUMENT PANEL
Removal & Installation (Dakota & Durango)
1) Disconnect negative battery cable. Disable air bag system.
See AIR BAG SYSTEM SAFETY article. Place front wheels in straight-
ahead position. Remove sill trim from both doorways. Remove kick panel
covers from both sides of vehicle. Remove mounting screws for hood
release handle.
2) Remove steering column trim panel and support bracket.
Remove tilt steering column lever (if equipped). Remove upper and
lower shrouds from steering column. Unplug driver's side air bag
module. Loosen multifunction switch wiring harness connector screw and
disconnect from switch. Screw will remain in connector.
3) Disconnect PRNDL cable. Disconnect shift cable from
steering column. Remove steering coupler lock pin. Remove toe plate
retaining screws. Remove steering column mounting bolts and remove
steering column from vehicle.
4) Remove screw from bulkhead wiring harness connector and
disconnect. Disconnect 2 body wiring harness connectors located next
to bulkhead connector. Disconnect 3 wiring harness connectors, from
junction block, located nearest to dash panel. Disconnect brake light
switch connector. Disconnect Rear Wheel Anti-Lock (RWAL) brake module
(if equipped), located near steering column support brackets.
5) Disconnect plastic retainer clip from parking brake
linkage rod, located at back of parking brake release handle. Remove
rod end from parking brake handle. Remove instrument panel center
support bracket. Unplug vacuum harness connector located at left end
of A/C-heater housing. Disconnect Air Bag Control Module (ACM)
connector.

6) Remove glove box. Reach through glove box opening and
disconnect antenna coaxial cable connector. Disconnect blower motor
connector located above glove box opening, near support brace for A/C-
heater housing. Disconnect radio ground strap. Loosen instrument panel
roll down bracket bolts about 2 turns, located at lower corners on
both sides of instrument panel. Remove 5 screws across top of dash
panel at base of windshield, removing center screw last.
7) Roll down instrument panel and install a temporary support
hook that is about 18" (457 mm) in length. Install hook from center
hole in instrument panel to center hole of dash panel. Pull lower
instrument panel outward until both roll down bracket bolts are in
slotted roll down position. Instrument panel should now be supported
and away from firewall.
8) Disconnect 2 door harness connectors, located on a bracket
near right end of instrument panel. Disconnect blower motor resistor.
Disconnect temperature control cable from A/C-heater housing and
remove from housing. See Fig. 5. Disconnect demister duct flexible
hose from A/C-heater housing.
9) Ensure instrument panel is free and clear for removal.
With the aid of an assistant, remove temporary support hook. Lift
instrument panel off of roll down bracket bolts and remove from
vehicle.
10) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.
Removal & Installation (Ram Pickup)
1) Disable air bag system. See AIR BAG SYSTEM SAFETY article.
Disconnect negative battery cable. Drain cooling system. Remove left
and right kick panel trim. Remove 5 screws and knee bolster/steering
column cover. Remove hood release and parking brake release handle
screws from lower instrument panel support. Remove 6 screws and
instrument panel support. Disconnect air bag connector at lower left
corner of instrument panel.
2) Pull PRNDL cable and twist to remove from position arm.
Push tab on bottom of cable retainer upward, then squeeze sides to
remove retainer from column. Remove tilt lever (tilt column only).
Remove both upper and lower shrouds from column. Remove lower fixed
column shroud. Loosen multifunction switch connector screw. Screw will
remain in connector.
3) Remove remaining steering column electrical connectors.
Remove air bag wiring harness from steering column wiring trough.
Remove wiring trough from steering column. Remove 3 toe plate nuts and
washers.
4) Remove 2 nuts and washers attaching steering column
bracket to instrument panel steering column support bracket. Allow
column to lower and rest on seat. Remove 2 screws from bottom of Air
Bag Control Module (ACM) cover. Remove 4 screws holding ACM to
transmission tunnel.
5) Disconnect wiring at ACM. Disconnect instrument panel left
side wiring connectors. Remove screw holding brake release to bottom
of instrument panel. Disconnect instrument panel right side wiring
connectors, which includes 2 connectors attached to A/C-heater
assembly housing, courtesy light connector, antenna cable and 2 body
connectors. Disconnect vacuum harness from A/C-heater system.
6) Remove 5 screws holding instrument panel to dash. Loosen
lower instrument panel pivot bolts. Roll instrument panel downward.
Remove instrument panel from vehicle.
7) To install, reverse removal procedure. Ensure all wiring
and hoses are clear and not pinched. Tighten bolts and nuts to
specification. See TORQUE SPECIFICATIONS . Enable air bag system. See
AIR BAG SYSTEM SAFETY article.

as necessary. If connector and terminals are okay, turn ignition on.
Measure voltage between ground and 5-volt supply circuit at
transmission solenoid harness connector. If voltage is 4.5 volts or
less, repair open 5-volt supply circuit. If voltage is greater than 4.
5 volts, replace governor pressure sensor.
13) Turn engine off. Install transmission control relay.
Drain transmission fluid and remove oil pan. Inspect pan for burnt oil
and debris. Repair transmission as necessary. See appropriate
AUTOMATIC TRANSMISSION OVERHAUL article. If transmission is okay, go
to next step.
14) Replace governor pressure solenoid. Replace transmission
oil pan and refill fluid. Start engine. Remove transmission control
relay. Depress brake pedal and place gear selector in "D" position.
Read gauge pressure. If pressure is 40-55 psi (2.8-3.9 kg/cm
),
testing is complete. If pressure is not as specified, replace valve
body.
15) Conditions required to set DTC P1756 are not present at
this time. Using scan tool, clear DTCs. Start engine and check for
DTCs. Wiggle wiring harness between governor pressure sensor and PCM.
Note if DTC P1756 resets. If DTC P1756 resets, repair wiring harness
as necessary. If DTC P1756 does not reset, see INACTIVE DTC CONDITION
under SELF-DIAGNOSTIC SYSTEM. Testing is complete.
DTC P1757: GOV PRES ABOVE 3 PSI IN GEAR WITH 0 MPH
Circuit Description
Circuit is monitored continuously while key is on and engine
running, not in Park or Neutral position or with Malfunction Indicator
Light (MIL) illuminated. Code sets if governor pressure sensor is
greater than 3 psi (.2 kg/cm
) when requested pressure is zero with
governor pressure solenoid duty cycle at 95 percent for 2.65 seconds.
Test must fail twice to set code.
Possible Causes
* Other transmission codes are set.
* Solenoid pack connector 5-volt supply circuit open.
* Governor pressure sensor defective.
* Wiring harness and/or connectors defective.
* Transmission fluid burnt or oil pan has excessive debris.
* Valve body defective.
Diagnostic Procedures
1) Using scan tool, read DTCs. On AN and DN bodies, go to
next step. On all except AN and DN bodies, if DTC SPECIFIC GOOD TRIPS
counter is not displayed or displayed count is not "0", go to step 8).
If DTC SPECIFIC GOOD TRIPS counter is displayed and displayed count is
"0", go to next step.
2) Repair any other transmission related DTCs before
proceeding. If no other transmission related DTCs exist, go to next
step.
3) Start engine. Allow engine to reach normal operating
temperature. Set parking brake, depress brake pedal and place gear
selector in "D" position. Using scan tool, read governor pressure
sensor value. If value is greater than 3 psi (.2 kg/cm
), go to next
step. If value is 3 psi (.2 kg/cm) or less, go to step 8).
4) Turn ignition off. Install a pressure gauge at governor
pressure test port. See TESTING in appropriate AUTOMATIC TRANSMISSION
OVERHAUL article. Start engine. With gear selector in "D" position,
read gauge pressure. If pressure is less than 3 psi (.2 kg/cm
), go to
step 7). If pressure is 3 psi (.2 kg/cm) or greater, go to next step.
5) Turn engine off. Drain transmission fluid and remove oil
pan. Inspect oil pan for burnt oil and debris. Repair transmission as

circuit.
ONE GAUGE NOT OPERATING PROPERLY
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Push and hold RESET button while cycling ignition key; ON-
OFF-ON. Instrument cluster self-test will start. If inoperative gauge
reached proper calibration point, go to next step. If inoperative
gauge did not reach proper calibration point, replace instrument
cluster.
2) Stop instrument cluster self-test. If problem is with
speedometer, go to next step. If problem is with oil pressure gauge,
go to step 5). If problem is with temperature gauge, go to step 14).
If problem is with fuel level gauge, go to appropriate SELF-
DIAGNOSTICS article in ENGINE PERFORMANCE section and review
powertrain symptoms. If problem is with volt gauge, go to step 16). If
problem is with tachometer, go to step 18).
3) Using scan tool, select BODY, SYSTEMS TESTS then PCM
MONITOR. If scan tool displays PCM ACTIVE ON BUS, go to next step. If
scan tool does not display PCM ACTIVE ON BUS, go to appropriate
VEHICLE COMMUNICATIONS article.
4) Raise and support all wheels. Start engine and place gear
selector in drive. Using scan tool, select MIC, MONITORS then CCD BUS
ENGINE INFO. Read VSS. If vehicle speed on scan tool matches
speedometer, see appropriate ANTI-LOCK BRAKE article. If vehicle speed
on scan tool does not match speedometer, replace instrument cluster
circuit board.
5) Turn ignition on. If CHECK GAUGES light illuminated, go to
next step. If CHECK GAUGES light did not illuminate, go to step 11).
6) Turn ignition off. Inspect oil level. If oil level is
within specification, go to next step. If oil level is not within
specification, adjust oil level and retest.
7) Turn ignition on. Disconnect engine Oil Pressure Switch
(OPS) connector. OPS is located near bottom of distributor. If CHECK
GAUGES light went out, go to next step. If CHECK GAUGES light did not
go out, go to step 10).
8) Remove OPS. Connect mechanical oil pressure gauge to OPS
port. Start engine. If engine oil pressure at idle is 4 psi or more,
go to next step. If engine oil pressure at idle is less than 4 psi,
repair mechanical engine problem.
9) Run engine to reach normal operating temperature. If
engine oil pressure at idle is 4 psi or more, replace OPS. If engine
oil pressure at idle is less than 4 psi, repair mechanical engine
problem.
10) Turn ignition off. Disconnect PCM White connector C2. PCM
is located in engine compartment on right inner fender. Using an
external ohmmeter, measure resistance between ground and PCM Black
connector terminal No. 23 (Gray/Orange wire). If resistance is less
than 5 ohms, repair short to ground in Gray/Orange wire. If resistance
is 5 ohms or more, replace PCM.
11) Disconnect engine Oil Pressure Switch (OPS) connector.
OPS is located near bottom of distributor. Using an external ohmmeter,
measure resistance between ground and OPS connector Black/Light Blue
wire. If resistance is less than 5 ohms, go to next step. If
resistance is 5 ohms or more, repair open Black/Light Blue wire.
Black/Light Blue wire is a common sensor ground. If no other engine
sensors are failed, repair ground between sensor and splice. If


* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *

1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS