1999 DODGE RAM brake light

10.4 volts. FTC P1595 will set if vacuum and vent solenoids do not
respond when actuated by PCM.
Possible Causes:
* Ground circuit open.
* S/C brake switch output circuit open.
* S/C power supply circuit open or shorted.
* S/C servo defective.
* S/C vacuum solenoid control circuit open or shorted.
* S/C vent solenoid control circuit open or shorted.
* Brake switch defective or out of adjustment.
* Defective PCM.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
1) Turn ignition on. Turn Speed Control (S/C) on. Using scan\
tool, actuate S/C vent solenoid. If speed control servo clicks, go to
next step. If S/C servo does not click, go to step 7).
2) Using scan tool, actuate S/C vacuum solenoid. If S/C servo
clicks, go to next step. If S/C servo does not click, go to step 6).
3) Turn ignition on. Using scan tool, actuate S/C vacuum
solenoid. Wiggle wiring harness between S/C servo and brake switch to
PCM while scan tool is still actuating speed control vacuum solenoid.
If wiggling did not cause an interruption of S/C servo actuation, go
to next step. If wiggling caused an interruption of S/C servo
actuation, repair wiring harness as necessary. Perform TEST VER-4A
under VERIFICATION TESTS.
4) Turn ignition off. Inspect S/C wiring and connectors.
Clean or repair as necessary. Perform TEST VER-4A under VERIFICATION
TESTS. If wiring and connectors are okay, go to next step.
5) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, test is complete. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
6) Using scan tool, actuate S/C vent solenoid. Wiggle wiring
harness between S/C servo and brake switch to PCM while scan tool is
still actuating speed control vacuum solenoid. If wiggling did not
cause interruption of S/C servo actuation, go to next step. If
wiggling caused interruption of S/C servo actuation, repair wiring
harness as necessary. Perform TEST VER-4A under VERIFICATION TESTS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
7) Turn ignition off. Disconnect S/C servo 4-pin connector.
Inspect all related wiring and connectors and repair as necessary.
Turn ignition on. Turn S/C switch on. Using a 12-volt test light,
probe brake switch output circuit at S/C servo connector terminal No.
3 (Dark Blue/Red wire). If test light is illuminated and bright, go to\
next step. If test light is dim or not illuminated, go to step 13).
8) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
9) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance between ground and
S/C vacuum solenoid control circuit at S/C servo connector terminal

No. 1 (Tan/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
10) Using an ohmmeter, check resistance between ground and
S/C vent solenoid control circuit at S/C servo connector terminal No.
2 (Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, go to next step.
11) Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between S/C servo connector terminal No. 1
and PCM connector C3, terminal No. 4 (Tan/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
12) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between S/C servo connector terminal No. 2 and PCM
connector C3, terminal No. 5 (Light Green/Red wire). If resistance is
5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace S/C
servo. Perform TEST VER-4A under VERIFICATION TESTS.
13) Using an ohmmeter, check resistance between ground and
brake switch output circuit at S/C servo connector terminal No. 3
(Dark Blue/Red wire). If resistance is less than 5 ohms, repair short
to ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance
is 5 ohms or more, go to next step.
14) Reconnect PCM. Disconnect brake switch connector. Turn
ignition on. Turn S/C on. Using a 12-volt test light, probe S/C power
supply circuit at brake switch connector terminal No. 3 (Yellow/Red
wire). If test light is illuminated and bright, go to next step. If
test light is not illuminated or dim, go to step 17).
15) Turn ignition off. Using an ohmmeter, check resistance of
S/C brake switch output circuit between S/C servo connector terminal
No. 3 and brake switch connector terminal No. 4 (Dark Blue/Red wire).
If resistance is 5 ohms or more, repair open circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
16) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, replace
brake switch. Perform TEST VER-4A under VERIFICATION TESTS.
17) Turn ignition off. Disconnect PCM. Inspect connectors.
Clean or repair as necessary. Using an ohmmeter, measure resistance of
S/C power supply circuit between PCM connector C3, terminal No. 11 and
brake switch connector terminal No. 3 (Yellow/Red wire). If resistance\
is 5 ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace PCM.
Perform TEST VER-4A under VERIFICATION TESTS.
FTC P1596: SPEED CONTROL SWITCH ALWAYS HIGH
FTC P1596 will set if an open circuit is detected in Speed
Control (S/C) switch circuit when ignition is on.
Possible Causes:
* Defective clockspring.
* S/C switch ground circuit open.
* Defective ON/OFF switch.
* Defective PCM.
* S/C switch signal circuit open or shorted to voltage.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR

voltage. If voltage is less than one volt, go to next step. If voltage
is one volt or more, condition to set FTC is not present at this time.
Test is complete.
2) While observing scan tool, disconnect S/C ON/OFF switch.
If S/C switch voltage changes to 5 volts, replace S/C ON/OFF switch.
Perform TEST VER-4A under VERIFICATION TESTS. If voltage does not
change to 5 volts, go to next step.
3) While observing scan tool, disconnect S/C RESUME/ACCEL
switch. If S/C switch voltage changes to 5 volts, replace S/C
RESUME/ACCEL switch. Perform TEST VER-4A under VERIFICATION TESTS. If
voltage does not change to 5 volts, go to next step.
4) Turn ignition off. Ensure both S/C switches are still
disconnected. Using an ohmmeter, check resistance between S/C switch
connector terminals (S/C switch signal circuit and S/C switch ground
circuit). If resistance is less than 5 ohms, repair short circuit.
Perform TEST VER- 4A under VERIFICATION TESTS. If resistance is 5 ohms
or more, go to next step.
5) Disconnect clockspring 4-pin connector. Clockspring 4-pin
connector is located behind steering wheel. Inspect connector. Clean
or repair as necessary. Using an ohmmeter, check resistance between
ground and S/C switch signal circuit at clockspring connector (Dark
Green/Red wire on all models except Ram Van and Ram Wagon; wire color
is not available for Ram Van and Ram Wagon). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
6) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance between ground and S/C
switch signal circuit at either S/C switch connector (Dark Green/Red
wire on all models except Ram Van and Ram Wagon; wire color is not
available for Ram Van and Ram Wagon). If resistance is less than 5
ohms, repair short to ground. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is 5 ohms or more, replace PCM. Perform TEST VER-
4A under VERIFICATION TESTS.
FTC P1683: SPEED CONTROL POWER RELAY CIRCUIT
FTC P1683 will set if Speed Control (S/C) power supply
circuit is open or shorted when S/C is turned on.
Possible Causes:
* Brake switch out of adjustment.
* S/C brake switch output circuit open or shorted.
* Defective S/C servo.
* Defective brake switch.
* S/C vacuum or vent solenoid control circuits open or
shorted.
* Defective PCM.
* Ground circuit open.
* S/C power supply circuit open.
NOTE: For component locations, see COMPONENT LOCATIONS. For
connector terminal identification, see CONNECTOR
IDENTIFICATION. For wiring diagram, see WIRING DIAGRAMS.
NOTE: Ensure brake pedal is not depressed during the following
steps.
1) Turn ignition off. Disconnect S/C servo connector. Inspect
connector. Clean or repair as necessary. Turn ignition on. Using scan
tool, actuate S/C relay. Using a 12-volt test light, probe S/C brake
switch output circuit at S/C servo connector terminal No. 3 (Dark
Blue/Red wire). If test light is illuminated and bright, go to next

step. If test light is dim or not illuminated, go to step 7).
2) Turn ignition off. Using an ohmmeter, check resistance of
ground circuit at S/C servo connector terminal No. 4 (Black wire). If
resistance is 5 ohms or more, repair open ground circuit. Perform TEST
VER-4A under VERIFICATION TESTS. If resistance is less than 5 ohms, go
to next step.
3) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, measure resistance of S/C vacuum
solenoid control circuit between PCM connector C3, terminal No. 4 and
S/C servo connector terminal No. 1 (Tan/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
4) Using an ohmmeter, check resistance between ground and S/C
vacuum solenoid control circuit at S/C servo connector terminal No. 1
(Tan/Red wire). If resistance is less than 5 ohms, repair short to
ground. Perform TEST VER-4A under VERIFICATION TESTS. If resistance is
5 ohms or more, go to next step.
5) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between PCM connector C3, terminal No. 5 and S/C servo
connector terminal No. 2 (Light Green/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, go to next
step.
6) Using an ohmmeter, check resistance between ground and S/C
vent solenoid control circuit at S/C servo connector terminal No. 2
(Light Green/Red wire). If resistance is less than 5 ohms, repair
short to ground. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is 5 ohms or more, replace S/C servo. Perform TEST VER-4A
under VERIFICATION TESTS.
7) Turn ignition off. Disconnect brake switch connector.
Inspect connectors. Clean or repair as necessary. Turn ignition on.
Using scan tool, actuate S/C solenoid. Using a 12-volt test light,
probe S/C power supply circuit at brake switch connector terminal No.
4 (Yellow/Red wire). If test light is illuminated and bright, go to
next step. If test light is not illuminated or dim, go to step 10).
8) Check brake switch adjustment. See BRAKE SWITCH under
REMOVAL & INSTALLATION. Adjust as necessary. Perform TEST VER- 4A
under VERIFICATION TESTS. If brake switch adjustment is okay, go to
next step.
9) Using an ohmmeter, check resistance of brake switch output
circuit between brake switch connector terminal No. 3 and S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is more
than 5 ohms, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or less, replace brake
switch. Perform TEST VER-4A under VERIFICATION TESTS.
10) Turn ignition off. Using an ohmmeter, check resistance
between ground and S/C brake switch output circuit at S/C servo
connector terminal No. 3 (Dark Blue/Red wire). If resistance is less
than 5 ohms, repair short to ground. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is 5 ohms or more, go to next step.
11) Disconnect PCM. Inspect connectors. Clean or repair as
necessary. Using an ohmmeter, check resistance of S/C power supply
circuit between PCM connector C3, terminal No. 11 and brake switch
connector terminal No. 4 (Yellow/Red wire). If resistance is 5 ohms or\
more, repair open circuit. Perform TEST VER-4A under VERIFICATION
TESTS. If resistance is less than 5 ohms, replace PCM. Perform TEST
VER-4A under VERIFICATION TESTS.
FTC P1899: PARK/NEUTRAL POSITION (PNP) SWITCH STUCK IN PARK
OR IN GEAR (A/T MODELS)
Possible Causes:

next step. If scan tool does not display brake pedal PRESSED and
RELEASED, go to NTC-1: BRAKE SWITCH SENSE.
4) Turn S/C on. On A/T models, move gear selector to Drive.
If scan tool displays park neutral switch D/R, go to next step. If
scan tool does not display park neutral switch D/R, go to FTC P1899:
PARK/NEUTRAL POSITION SWITCH STUCK IN PARK OR IN GEAR under DIAGNOSTIC
TESTS.
5) On all models, using scan tool, actuate S/C vent solenoid.
Using a 12-volt test light, backprobe S/C brake switch output circuit
at S/C servo connector terminal No. 3 (Dark Blue/Red wire). If test
light is illuminated and bright, go to next step. If test light is dim
or is not illuminated, go to NTC-1: BRAKE SWITCH SENSE.
6) Start engine and let idle for one minute. Turn engine off.
Turn ignition on (engine off). Using scan tool, actuate S/C servo
solenoids. If throttle opens and closes, go to NTC-2: CHECKING FOR
SPEED CONTROL DENIED MESSAGE. If throttle does not open and close,
inspect throttle cable and linkage. Check vacuum supply. See VACUUM
SUPPLY under COMPONENT TESTS. Repair as necessary. Perform TEST VER-4A
under VERIFICATION TESTS.
7) While observing scan tool, press CANCEL switch several
times. If scan tool displays PRESSED and RELEASED, go to next step. If
scan tool does not display PRESSED and RELEASED, replace CANCEL
switch. Perform TEST VER-4A under VERIFICATION TESTS.
8) Turn ignition off. Disconnect S/C servo connector. Using
an ohmmeter, check resistance of ground circuit at S/C servo connector
terminal No. 4 (Black wire). If resistance is 5 ohms or more, repair
open ground circuit. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is less than 5 ohms, go to next step.
9) Reconnect S/C servo connector. Turn ignition and S/C on.
While observing scan tool, press SET switch several times. If scan
tool displays PRESSED and RELEASED, go to next step. If scan tool does
not display PRESSED and RELEASED, replace SET switch. Perform TEST
VER-4A under VERIFICATION TESTS.
10) Turn ignition off. Disconnect S/C servo connector.
Inspect terminals. If any terminal is damaged, pushed out or miswired,
repair as necessary. Perform TEST VER-4A under VERIFICATION TESTS. If
terminals are okay, go to next step.
11) Disconnect S/C servo connector. Disconnect PCM
connectors. Inspect connectors. Clean or repair as necessary. Using an
ohmmeter, check resistance of S/C vacuum solenoid control circuit
between PCM connector C3, terminal No. 4 and S/C servo connector
terminal No. 1 (Tan/Red wire). If resistance is 5 ohms or more, repair\
open circuit. Perform TEST VER-4A under VERIFICATION TESTS. If
resistance is less than 5 ohms, go to next step.
12) Turn S/C on. While observing scan tool, press COAST
switch several times. If scan tool displays PRESSED and RELEASED, go
to next step. If scan tool does not display PRESSED and RELEASED,
replace COAST switch. Perform TEST VER-4A under VERIFICATION TESTS.
13) Using an ohmmeter, check resistance of S/C vent solenoid
control circuit between PCM connector C3, terminal No. 5 and S/C servo
connector terminal No. 2 (Light Green/Red wire). If resistance is 5
ohms or more, repair open circuit. Perform TEST VER-4A under
VERIFICATION TESTS. If resistance is less than 5 ohms, replace S/C
servo. Perform TEST VER-4A under VERIFICATION TESTS.
NTC-1: BRAKE SWITCH SENSE
Possible Causes:
* Ground circuit open.
* Defective brake switch.
* Brake switch sense circuit open or shorted.
* Defective PCM.

Fully depress brake pedal and rotate brake switch
counterclockwise approximately 30 degrees. Remove brake switch from
bracket. Depress lock tabs holding brake switch mounting bracket and
separate harness connector from brake switch.
Installation
1) Before installing brake switch, reset adjustable plunger
by pulling on plunger head until plunger reaches end of travel.
Connect harness connector to brake switch. Depress brake pedal and
insert brake switch into keyed hole in mounting bracket. Rotate brake
switch clockwise into locked position.
2) Gently pull back on brake pedal until pedal will go no
further. This causes the brake switch plunger to ratchet backward to
the correct position. No further adjustment is required.
SPEED CONTROL SERVO
Removal (Except Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Disconnect electrical
connector and vacuum hose from servo. Using finger pressure only, push
servo cable connector from throttle body bellcrank pin. DO NOT pull
cable connector perpendicular to bellcrank.
2) Remove 2 servo cable mounting nuts. Pull servo cable
sleeve away from mounting bracket to expose cable retaining clip.
Remove retaining clip. Remove servo.
Removal (Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Remove engine cover.
Remove air cleaner assembly. Using finger pressure only, push servo
cable connector from throttle body bellcrank pin. DO NOT pull cable
connector perpendicular to bellcrank.
2) Remove right headlight assembly. Disconnect vacuum hose
and electrical connector at servo. Remove 2 servo mounting bracket
bolts. Remove 2 servo cable mounting nuts. Pull servo cable sleeve
away from mounting bracket to expose cable retaining clip. Remove
retaining clip. Remove servo.
Installation (All Models)
With throttle in full open position, align hole in speed
control cable sleeve with hole in servo pin. Install retaining clip.
To complete installation, reverse removal procedure. Tighten mounting
bolts/nuts to 75 INCH lbs. (8.5 N.m).
SPEED CONTROL SWITCHES
Removal & Installation
Turn ignition off. Disconnect negative battery cable. Wait 2
minutes for air bag system to discharge reserve voltage. Remove 2
screws holding air bag assembly to steering column. Separate air bag
assembly from steering column and disconnect air bag, horn and speed
control switch connectors. Remove screws securing speed control switch
to air bag assembly. Separate speed control switch from air bag
assembly. To install, reverse removal procedure.
WIRING DIAGRAMS

horizontally, and clamp straightedge to yoke in a horizontal plane.
Repeat procedure with drive pinion flange. Ensure flange/yokes are
horizontal by checking angle of straightedge using a machinist spirit
level.
4) Measure distance "X" at each side. See Fig. 9. If
measurements are not within 1/16" (1.6 mm) of each other, transmission\
flange is horizontally misaligned.
5) Measure distance "Y" (edge of straightedge to axle shaft
center line) at each side. If measurements are not within 1/8" (3.2
mm) of each other, axle housing is misaligned. Measure distance "W" at
each side. If measurements are not within 1/16" (1.6 mm) of each
other, pinion flange is horizontally misaligned.
ADJUSTING HORIZONTAL ALIGNMENT
NOTE: Excessive difference in measurements may indicate frame
damage. DO NOT attempt to use following correction procedure
if more than slight horizontal misalignment exists.
Minor adjustment of drive shaft horizontal alignment may be
made by loosening axle housing "U" bolts and moving either side of
axle housing forward or backward. If frame is not bent, slight axle
movement should make "W" measurements equal. See Fig. 9.
REMOVAL & INSTALLATION
CENTER BEARING SUPPORT ASSEMBLY
Removal
1) With transmission in neutral and parking brake off, raise
vehicle. Scribe alignment marks on all flange/yokes and slip joints to
be disassembled or disconnected. Remove drive shaft from pinion
flange/yoke.
2) Slide rear drive shaft slip joint from front drive shaft
splines. See Fig. 10. Support drive shaft(s) while removing center
bearing support bracket mounting bolts. Pull to remove front drive
shaft slip joint from transmission extension housing shaft.
Fig. 10: Identifying Center Bearing Support Assembly Components
Courtesy of Chrysler Corp.
CAUTION: DO NOT clamp drive shaft tube or slip joint tube in a vise.
Clamp only forged portion of each yoke in vise. To avoid

Stoplight Switch On brake pedal bracket.








\









\









\









\









\









\









\







MISCELLANEOUS









\









\









\









\









\









\









\







Component Component Location








\









\









\









\









\









\









\







Blower Motor Resistor Block Behind right side of dash, on
A/C-heater housing.
Data Link Connector (DLC) Left bottom of dash.
Fuel Heater (Diesel) In top of fuel filter housing.
Ignition Coil 4-Pack & 6-Pack Right side of engine.