1996 TOYOTA TERCEL Service Repair Manual

- DIAGNOSTICSENGINE
DI-1 1
1996 TERCEL (RM440U)
Proceed to matrix chart of problem symp-
toms on page DI-19.
7. ENGINE OPERATING CONDITION
NOTICE:
The values given below for ºNormal Conditionº are representative values, so a vehicle may still be
normal even if its value from those listed here. So do not decide whether a part is faulty or not solely
according to the ºNormal Conditionº here.
CARB mandated signals:
TOYOTA hand-held tester displayMeasurement ItemNormal Condition*
FUEL SYS #1
Fuel System Bank 1
OPEN: Air-fuel ratio feedback stopped
CLOSED: Air-fuel ratio feedback operating
Idling after warming up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 19.7 - 47.4 %
Racing without load (2,500rpm): 18.8 - 46.4 %
COOLANT TEMP.Engine Coolant Temp. Sensor ValueAfter warming up: 80 - 95°C (176 - 203°F)
SHORT FT #1Short-term Fuel Trim Bank 10 ± 20%
LONG FT #1Long-term Fuel Trim Bank 10 ± 20%
ENGINE SPDEngine SpeedIdling: 700 - 800 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance:
Ignition Timing of Cylinder No. 1Idling: BTDC 7 - 14°
INTAKE AIRIntake Air Temp. Sensor ValueEquivalent to Ambient Temp.
MAPAbsolute Pressure Inside Intake Manifold
Idling: 20 - 48 kPa
Racing without load (2,500 rpm):
19 - 47 kPa
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a percentage:
0 V "0%, 5 V "100%Throttle Fully Closed: 6 - 16 %
Throttle Fully Open: 64 - 98 %
O2S B1, S1Voltage Output of Heated Oxygen Sensor
Bank 1, Sensor 1Idling: 0.1 - 0.9 V
O2FT B1, S1Oxygen Sensor Fuel Trim Bank 1, Sensor 1
(Same as SHORT FT #1)0 ± 20 %
O2S B1, S2Voltage Output of Oxygen Sensor
Bank 1, Sensor 2Driving at 50 km/h (31 mph): 0.1 - 0.9 V
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

DI-12
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
TOYOTA Enhanced Signals:
TOYOTA hand-held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.66 - 3.9 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 25.5 - 43 %
STARTER SIGStarter SignalCranking: ON
CTP SIGClosed Throttle Position SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N position: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1, CYL#2, CYL#3, CYL#4Abnormal revolution variation for each cylinder0%
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 - 2,000 rpm
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 - 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from lean to rich.
Idling after warmed up: 0 - 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from rich to lean.
Idling after warmed up: 0 - 1,000 msec.
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

DI4LF-02
- DIAGNOSTICSENGINE
DI-13
1996 TERCEL (RM440U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below, for details of each code, turn to the page referred to under the ''See page '' for the respec-
tive ''DTC No.'' in the DTC chart.
SAE Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P0105
(DI-20)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
MalfunctionOpen or short in manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM

P0106
(DI-23)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
Range/Performance Problem
Manifold absolute pressure sensor
P0110
(DI-24)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM

P0115
(DI-28)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI-32)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI-33)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI-37)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
Range/Performance Problem
Throttle position sensor
P0125
(DI-38)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in oxygen sensor circuit
Oxygen sensor
P0130
(DI-41)Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
P0133
(DI-44)Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Oxygen sensor
P0136
(DI-45)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI-47) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM

*: 


MIL lights up

DI-14
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)DTC No.
(See Page)
Detection ItemTrouble AreaMIL*Memory
P0171
(DI-49)System too Lean
(Fuel Trim)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0172
(DI-49)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0300
(DI-52)Random/Multiple Cylinder
Misfire DetectedIgnition system
Injector
FlliP0301
P0302
P0303
P0304
(DI-52)Misfire Detected
- Cylinder 1
- Cylinder 2
- Cylinder 3
- Cylinder 4Fuel line pressure
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0325
(DI-57)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM

P0335
(DI-60)Crankshaft Position Sensor
Circuit ºAº Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM

P0340
(DI-63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM

P0420
(DI-73)Catalyst System Efficiency
Below ThresholdThree-way catalytic converter
Open or short in (heated) oxygen sensor circuit
(Heated) oxygen sensor

P0500
(DI-76)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Speedometer cable
ECM

P0505
(DI-78)Idle Control System
Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short in AC1 switch circuit
Air intake (hose loose)

*: 


MIL lights up

- DIAGNOSTICSENGINE
DI-15
1996 TERCEL (RM440U)
Manufacturer Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P1300
(DI-84)Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM

P1335
(DI-89)Crankshaft Position Sensor
Circuit Malfunction
(during engine running)Open or short in crankshaft position sensor circuit
Crankshaft position sensor
ECM
-
P1600
(DI-92)ECM BATT MalfunctionOpen in back up power source circuit
ECM
P1780
(DI-94)Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
Park/neutral position switch
ECM

*:-


MIL does not light up



MIL lights up

DI4LG-02
A15676
DI-16
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
PARTS LOCATION

DI4LH-02
P19551
ECM TerminalsE7 E6
1 2 3 4 5 6 7 8 9 10 11 12 13
23 24 25 26 1920 21 22 18 1415 16 171 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
- DIAGNOSTICSENGINE
DI-17
1996 TERCEL (RM440U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E6-2) - E1 (E7-24)W-R - BRAlways9 - 14
+B (E6-9) - E1 (E7-24)B-R - BRIG switch ON9 - 14
VC (E7-18) - E2 (E7-16)LG-R - BRIG switch ON4.5 - 5.5
VTA (E7 19) E2 (E7 16)YG BR
IG switch ON
Throttle valve fully closed0.3 - 1.0
VTA (E7-19) - E2 (E7-16)Y-G - BRIG switch ON
Throttle valve fully open3.2 - 4.9
PIM (E7 4) E2 (E7 16)PBRIG switch ON3.3 - 3.9PIM (E7-4) - E2 (E7-16)P - BRApply vacuum 26.7 kPa (200 mmHg, 7.9 in.Hg)2.5 - 3.1
THA (E7-15) - E2 (E7-16)L-B - BRIdling, Intake air temp. 20°C (68° F)0.5 - 3.4
THW (E7-3) - E2 (E7-16)G-B - BRIdling, Engine coolant temp. 80°C (176°F) 0.2 - 1.0
STA (E7-11) - E1 (E7-24)B-W - BRCranking6.0 or more
IG switch ON9 - 14
#10 (E7-12) - E01 (E7-13)G - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#20 (E7-11) - E01 (E7-13)Y - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#30 (E7-25) - E01 (E7-13)R - BRIdlingPulse generation
(See page DI-52)
IG switch ON9 - 14
#40 (E7-24) - E01 (E7-13)L - BRIdlingPulse generation
(See page DI-52)
IGT1 (E7-6) - E1 (E7-24)LG - BRIdlingPulse generation
(See page DI-84)
IGT2 (E7-5) - E1 (E7-24)L-Y - BRIdlingPulse generation
(See page DI-84)
IG switch ON, Disconnect igniter connector4.5 - 5.5
IGF (E7-7) - E1 (E7-24)LG-B - BRIdlingPulse generation
(See page DI-84)
G2(E7-20) - NE- (E7-9)R - WIdlingPulse generation
(See page DI-60)
NE(E7-21) - NE- (E7-9)B - WIdlingPulse generation
(See page DI-60)
FC (E6-4) - E1 (E7-24)G-B - BRIG switch ON9 - 14

DI-18
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)Symbols (Terminals No.)
Wiring ColorConditionSTD Voltage (V)
RSC (E7-1) - E1 (E7-24)L-R - BRIG switch ON
Disconnect ºE7º of ECM connector9 - 14
RSO (E7-14) - E1(E7-24)L - BRIG switch ON
Disconnect ºE7º of ECM connector9 - 14
OX1 (E7-10) - E1 (E7-24)B - BRMaintain engine speed at 2,500 rpm for 2 minutes. after
warming upPulse generation
OX2 (E7-23) - E1 (E7-24)W - BRMaintain engine speed at 2,500 rpm for 2 minutes. after
warming upPulse generation
HT1 (E6 6) E03 (E7 26)WL BRIdlingBelow 3.0HT1 (E6-6) - E03 (E7-26)W-L - BRIG switch ON9 - 14
HT2 (E6 5) E03 (E7 26)WR BRIdlingBelow 3.0HT2 (E6-5) - E03 (E7-26)W-R - BRIG switch ON9 - 14
KNK (E7-8) - E1 (E7-24)B - BRIdlingPulse generation
(See page DI-57)
NSW (E7 2) E1 (E7 24)(M/T)
IG switch ON
Other shift position in ºPº or ºNº position9 - 14
NSW (E7-2) - E1 (E7-24)(M/T)IG switch ON
Shift position in ºPº or ºNº position0 - 3.0
NSW (E7 2) E1 (E7 24)(A/T)
IG switch ON
Other shift position in ºPº or ºNº position9 - 14
NSW (E7-2) - E1 (E7-24)(A/T)IG switch ON
Shift position in ºPº or Nº position0 - 3.0
SPD (E6-13) - E1 (E7-24)Y - BRIG switch ON
Rotate driving wheel slowlyPulse generation
(See page DI-76)
TE1 (E6-8) - E1 (E7-24)G - BRIG switch ON9 - 14
W (E6 10) E1 (E7 24)GR L BRIdling9 - 14W (E6-10) - E1 (E7-24)GR-L - BRIG switch ONBelow 3.0
AC1 (E6 12) E1 (E7 24)LG B BRIdling, A/C switch ONBelow 2.0AC1 (E6-12) - E1 (E7-24)LG-B - BRIdling, A/C switch OFF9 - 14
ACT (E6 14) E1 (E7 24)LBRIdling, A/C switch ON9 - 14ACT (E6-14) - E1 (E7-24)L - BRIdling, A/C switch OFFBelow 2.0
ODSW (E6 3) E1 (E7 24)RW BRIG switch ON, O/D main switch pushed out9 - 14ODSW (E6-3) - E1 (E7-24)R-W - BRIG switch ON, O/D main switch pushed in0 - 3.0
ODT (E6 11) E1 (E7 24)RBRIG switch ON, O/D main switch pushed out9 - 14ODT (E6-11) - E1 (E7-24)R - BRIG switch ON, O/D main switch pushed in0 - 3.0