1996 TOYOTA TERCEL lights

B02389
B02390
HEAT METHOD: When the problem seems to occur when the suspect area is heated. 2
NOTICE:3 WATER SPRINKLING METHOD:
(1)
(2)
4 OTHER: When a malfunction seems to occur when electrical load is excessive.When the malfunction seems to occur on a rainy day or in a
high-humidity condition. Heat the component that is the likely cause of the malfunction
with a hair dryer or similar object. Check to see if the malfunction
occurs.
Sprinkle water onto the vehicle and check to see if the malfunc-
tion occurs.
Turn on all electrical loads including the heater blower, head
lights, rear window defogger, etc. and check to see if the mal-
function occurs.ON HINT:
If a vehicle is subject to water leakage, the leaked water may
contaminate the ECU. When testing a vehicle with a water leak-
age problem, special caution must be taken.
Malfunc-
tion
Do not heat to more than 60°C (140°F). (Temperature
is limited not to damage the components.)
Do not apply heat directly to parts in the ECU. (1)
(2)
Never sprinkle water directly into the engine compart-
ment, but indirectly change the temperature and hu-
midity by applying water spray onto the radiator front
surface.
Never apply water directly onto the electronic compo-
nents. NOTICE:
- INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN-21
1996 TERCEL (RM440U)

MA002-30
MA-2
- MAINTENANCEINSIDE VEHICLE
40 Author
: Date
:
1996 TERCEL (RM440U)
INSIDE VEHICLE
GENERAL MAINTENANCE
The owners are responsible for these maintenance and inspection items.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every service item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.

Failure to do even one item can cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified freeplay. Be alert for changes in steering condition, such as hard steering,
excessive freeplay or strange noises.
11. SEATS
(a) Check that all front seat controls such as seat adjusters, seatback reliner, etc. operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the locks hold securely in any latched position.
(d) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latched position.
(e) For fold-down rear seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.

FI0534
DI4LE-02
P19552
TOYOTA Hand-Held Tester
DLC3
- DIAGNOSTICSENGINE
DI-3
1996 TERCEL (RM440U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Description

When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you need to connect OBD II scan tool comply-
ing with SAE 1978 or TOYOTA hand-held tester to
the vehicle and read off various data output from the
vehicle's ECM.

OBD II regulations require that the vehicle's on-
board computer lights up the Malfunction Indicator
Light (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in a drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Code (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI-13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTC remain recorded in the ECM memory.

To check the DTC, connect the OBD II scan tool or
TOYOTA hand-held tester to Data Link Connector
3 (DLC3) on the vehicle. The OBD II scan tool or
TOYOTA hand-held tester also enables you to
erase the DTC and check freezed frame data and
various forms of engine data (For operating instruc-
tions, see the OBD II scan tool's instruction book.).

DTC include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI-13).

FI3605
Flashing
ON
OFF
0.13 Seconds
DI-6
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand-held tester) to check the DTC, use
the normal mode. For code on the DTC chart subject to º2
trip detection logicº, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTC are recorded in
the ECM.
3. Check Mode:
INSPECT DIAGNOSIS
HINT:
TOYOTA hand-held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC.
(1) Initial conditions.

Battery positive voltage 11V or more.

Throttle valve fully closed.

Transmission in ºPº or ºNº position.

Air conditioning switched OFF.
(2) Turn the ignition switch OFF.
(3) Prepare the TOYOTA hand-held tester.
(4) Connect the TOYOTA hand-held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and switch the TOYOTA
hand-held tester ON.
(6) Switch the TOYOTA hand-held tester normal mode
to check mode. (Check that the MIL flashes.)
(7) Switch the engine. (The MIL goes out after the en-
gine start.)
(8) Simulate the conditions of the malfunction de-
scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc.
(9) After simulating the malfunction conditions, use the
TOYOTA hand-held tester diagnosis selector to
check the DTC and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. Turning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTC, etc. are erased.
(10) After checking the DTC, inspect the applicable cir-
cuit.

DI4LF-02
- DIAGNOSTICSENGINE
DI-13
1996 TERCEL (RM440U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below, for details of each code, turn to the page referred to under the ''See page '' for the respec-
tive ''DTC No.'' in the DTC chart.
SAE Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P0105
(DI-20)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
MalfunctionOpen or short in manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM

P0106
(DI-23)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
Range/Performance Problem
Manifold absolute pressure sensor
P0110
(DI-24)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM

P0115
(DI-28)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI-32)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI-33)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI-37)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
Range/Performance Problem
Throttle position sensor
P0125
(DI-38)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in oxygen sensor circuit
Oxygen sensor
P0130
(DI-41)Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
P0133
(DI-44)Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Oxygen sensor
P0136
(DI-45)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI-47) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM

*: 


MIL lights up

DI-14
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)DTC No.
(See Page)
Detection ItemTrouble AreaMIL*Memory
P0171
(DI-49)System too Lean
(Fuel Trim)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0172
(DI-49)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0300
(DI-52)Random/Multiple Cylinder
Misfire DetectedIgnition system
Injector
FlliP0301
P0302
P0303
P0304
(DI-52)Misfire Detected
- Cylinder 1
- Cylinder 2
- Cylinder 3
- Cylinder 4Fuel line pressure
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0325
(DI-57)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM

P0335
(DI-60)Crankshaft Position Sensor
Circuit ºAº Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM

P0340
(DI-63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM

P0420
(DI-73)Catalyst System Efficiency
Below ThresholdThree-way catalytic converter
Open or short in (heated) oxygen sensor circuit
(Heated) oxygen sensor

P0500
(DI-76)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Speedometer cable
ECM

P0505
(DI-78)Idle Control System
Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short in AC1 switch circuit
Air intake (hose loose)

*: 


MIL lights up

- DIAGNOSTICSENGINE
DI-15
1996 TERCEL (RM440U)
Manufacturer Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P1300
(DI-84)Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM

P1335
(DI-89)Crankshaft Position Sensor
Circuit Malfunction
(during engine running)Open or short in crankshaft position sensor circuit
Crankshaft position sensor
ECM
-
P1600
(DI-92)ECM BATT MalfunctionOpen in back up power source circuit
ECM
P1780
(DI-94)Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
Park/neutral position switch
ECM

*:-


MIL does not light up



MIL lights up

- DIAGNOSTICSENGINE
DI-49
1996 TERCEL (RM440U)
DTC P0171 System too Lean (Fuel Trim)
DTC P0172 System too Rich (Fuel Trim)
CIRCUIT DESCRIPTION
ºFuelº trim refers to the feedback compensation value compared against the basic injection time. Fuel trim
includes short-term fuel trim and long-term fuel trim.
ºShort-term fuel trimº is the short-term fuel compensation used to maintain the air-fuel ratio at its ideal
theoretical value. The signal from the oxygen sensor indicates whether the air-fuel ratio is RICH or LEAN
compared to the ideal theoretical value, triggering a reduction in fuel volume if the air-fuel ratio is rich, and
an increase in fuel volume if it is lean.
ºLong-term fuel trimº is overall fuel compensation carried out long-term to compensate for continual devi-
ation of the short-term fuel trim form the central value due to individual engine differences, wear over time
and changes in the usage environment.
If both the short-term fuel trim and long-term fuel trim are LEAN or RICH beyond a certain value, it is de-
tected as a malfunction and the MIL lights up.
DTC No.DTC Detection ConditionTrouble Area
P0171
When the air-fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the RICH side
(2 trip detection logic)

Air intake (hose loose)

Fuel line pressure

Injector blockage

Heated oxygen sensor malfunction

Manifold absolute pressure sensor

Engine coolant temp. sensor
P0172
When the air-fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the LEAN side.
(2 trip detection logic)

Fuel line pressure

Injector blockage, leak

Heated oxygen sensor malfunction

Manifold absolute pressure sensor

Engine coolant temp. sensor
HINT:

When DTC P0171 is recorded, the actual air-fuel ratio is on the LEAN side. When DTC P0172 is re-
corded, the actual air-fuel ratio is on the RICH side.

If the total of the short-term fuel trim value and long-term fuel trim value is within + 25 %, the system
is functioning normally.

If the vehicle runs out of fuel, the air-fuel ratio is LEAN and DTC P0171 is recorded. The MIL then
comes on.
DI052-09